similar to: How to secure access to PSTN line through Linksys gateway?

Hi all, i need sample xml configuration files for linksys pap2, linksys pap-2t, sipura 2100, sipura 2102, 1001, 3000 and 3102. All of these are linksys/sipura products. So if anyone has these sample files then plz share. -- Best Regards Rizwan Hisham Software Engineer Axvoice Inc. www.axvoice.com -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have a linksys SPA 3102 with a DECT phone connected into its Telephone port. It has been working, but something I've done (and I don't know what) means that now everytime asterisk tries to dial it, it says it is busy. I can make calls from it through asterisk I am at a complete loss to know what to try next to fix it. Any ideas? -- Alan Chandler http://www.chandlerfamily.org.uk

Hi All, In our small office calls to the PSTN are currently sent via Asterisk and a Linksys SPA3102 (1 x FXO and 1 x FXS): SIP Phone --> Asterisk --> Linksys SPA3102 --> PSTN If the PSTN is in use on SPA3102 I need a way to get the call to then route out over IAX termination. SIP Phone --> Asterisk--> Linksys SPA3102 --> PSTN (In Use)

Does anybody know if the process of upgrading firmware on "Linksys SPA3102-NA" in Linux is the same as on Sipura 3K as described on voip-info.org http://www.voip-info.org/wiki/view/Sipura -- #Joseph GPG KeyID: ED0E1FB7

Hi, I have a Linksys SPA 3102 using as ATA. The call routing is : Phone -> PSTN -> SPA 3102 -> SIP Proxy -> Asterisk The problem I am having is that when the phone hangs up, SPA 3102 can't detect it and relay the CANCEL message. Is this problem with my SPA 3102 config or it just works like that by default? Thanks in advance for your help. Regards, Mark -------------- next

I am looking for a gateway/ATA that can take conversations on the analogue line (PSTN) and send them to the Asterisk server on the private network. I was experimenting with the Atcom AG-188N but the "FXO"-port only supports lifeline, so it's not a real FXO-port that can send incoming calls to my private Asterisk-server. Could someone advice on a gateway that can take analogue calls

Hi there, I was wondering if anyone has successfully used Asterisk as a dedicated Analog PSTN gateway to take the place of, for example, a Mediatrix 1204 or an 8 port model? Basically, I am thinking of using a Linksys SPA9000 as the PBX and just need an Analog PSTN gateway for 4 to 8 FXO lines. It does not sound like the Mediatrix 1204 does a very good job and I figure I can build a much more

Ok, I've done some more research and I don't think I want an FXO box... What I'd like to do is use BroadVoice (with their BYOD plan) and then run Asterisk on my WRT54G router. I'd also like to use my regular home phones without having to use a special "SIP" phone... (eg. I like my Vtech normal cordless phones) What do I need to buy to get this working? It sounds like I

Hello I'm using a Linksys 3102 as VoIP gateway to connect a POTS line to a PBX. I also have an IP phone in a remote network across the Net. The PBX + gateway, and the phone are both behind a NAT router. I was wondering: 1. When a customer calls us through the POTS line and I pick up the call with the remote IP phone, do RTP packets go directly from the VoIP gateway to the IP phone, or

Dear The Expert, I am very new with this, I have installed AsteriskNow, X-Lite as my SoftPhone, I am using SPA-3102. I have 3 extensions, me at 250, 998 is my Linksys SPA-3102 and 999 for PSTN Line (see below) My problem is, I am unable to call 998, I thought this is registration problem, (because the Linksys screen info said Registration Failed) Could any body please help? Many thanks in

Hi, I'm putting together a fax solution for my company that utilizes T.38. I wanted to throw out my plan and get some feedback if anyone is doing something similar or sees a blatant problem with it. We're currently rolling out SPA-942 phones for the standard desk phone with vanilla Asterisk 1.4.15 (just upgraded it today) on the back end. Most calls for satellite offices are handled by

I'm looking for a reliable ATA FXO/FXS adapter. Linksys 3102 - a lot of echo problem + two of them died within a year (not reliable) Sangoma USBFXO - problem installing drive in Gentoo. I've tried two Chines units: AG-188N and YGW30B none are of them have real FXO port that will register with Asterisk. Any other recommendations; (I don't like internal cards). -- Joseph

I run a bunch of the Linksys ATA's.. I always use rfc2833 for DTMF. works very well and have never had a problem with it. ..o-------------------------------------------------------o. Brian Fertig NOC/Network Engineer Planet Telecom, Inc. Tampa, FL Office -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of

Hello I use the Linksys 3102 to connect Asterisk to a POTS line, and XLite on XP as an SIP client: http://img694.imageshack.us/img694/1421/3102asteriskxlitecid.png The problem is that by default, Asterisk doesn't rewrite the CID name + number in incoming calls, so that XLite displays whatever name I used in the 3102 and the extension the 3102 uses to register with Asterisk. How can I tell

I have two old Sipura 3000 original (green) boxes and they are running perfectly faxes going through, no echo. Firmware 2.0.13(GWg), hardware 2.0.1(1813) Does the number in the bracket means anything? In addition I have Linksys 3000 running the same firmware and same hardware (except the number in the bracket). I can not get to work correctly. The unit has a lot of echo, can not get rid of it,

Is anybody using Call Waiting works on Linksys 3102? Does it work? If I'm on the phone, I can hear a notification 'beep', but when I put first caller on hold the line is busy. Linksys registers to Asterisk. -- #Joseph

Voxilla news story: http://voxilla.com/voxstory84-nested-order0-threshold0.html Two new products * A Sipura 2000 in a linksys box: Linksys PAP2 Phone Adapter * A combination NAT router with 2 FXS ports: Linksys RT31P2 Broadband Router Jim James H. Thompson jht@lava.net

I have a samba server running samba 3. I am not actually sure that this is samba not working or a linux printing thing. I have a Linksys PPSX1 Pocket Print Server and I am unable to print to the network printer. There are directions on the Linksys site but I get so far and the directions tell me to type a command that is not found. Is anyone printing to a Linksys Pocket Print Server? I need

Greetings list, I need to set up a point to point SIP connection between two devices without either of them registering with a registrar/proxy/etc. at all. The devices I've tested so far all seem to insist on having a registration before they'll make or take calls. One of the devices needs to be an ATA with an FXO port (e.g. Sipura/Linksys SPA-3000/3102), the other device can be either

Sorry, I am resending this, I tried earlier, but I couldn't see it appear on the archives - apologogies if it appears double! -------------------------------------------------- My Sipura 3000 ATA died on me this morning. I had a Linksys SPA 3102 available which I would like to use as a replacement. Unfortunately, the SPA3102 is not able to register with the asterisk server - I am