similar to: asterisk sip doesn't see other asterisk-sip

I would like to ask, if someone observe also problem with peer qualify problems, my asterisk log is full with UNREACHABLE/REACHABLE messages, even when two asterisks are in LAN environment, please take a look into this debug, I can't find any problem with packet loss, all qualify requests are replied and acknowledged, I will submit bug report, if you will also not find any problems here...

Hi all, I'm having a problem with some Asterisk servers interconnected with each other using IAX (I also tried with SIP without solving the problem) Sometimes, with apparently no reason, some peers become UNREACHABLE (I have qualify=yes in iax.conf) and REACHABLE again as soon as another qualify test is made. Our users are also complaining about audio loss during their calls, apparently

We have a problem with our iaxclients. Our asterisk runs on a public host with debian and many of our IAX2 clients are natted. The iax.conf looks like: [23456] accountcode=123 type=friend context=user auth=md5 secret=xxxx username=23456 callerid=Testuser 1 <23456> notransfer=yes host=dynamic The cli command IAX2 show peers shows all clients as unmonitored CLI> IAX2

Hi - I'm running CVS-HEAD from 2005-08-11 20:17:17 UTC, and I'm trying to set up some redundancy on IAX connections between locations. I have two IAX peers set up that work correctly by themselves: "ast551-out" and "ast551-out-backup": [ast551-out] type=peer secret=secret username=ast551 host=X.X.X.X qualify=1000 disallow=all allow=gsm allow=ulaw trunk=no

To answer my own message, I figured out a solution (untested) about 10 minutes after posting and leaving the office. Doh! Anyway, the solution (now tested) was to make the Asterisk server behind the NAT register with its peers. Despite reserving port 4569 in the firewall, that was not enough in this particular NAT firewall - it was only being reserved for one connection. Kind regards, Sebastian

The situation is one of my asterisk servers is behind a NAT firewall and one is not. Both servers have multiple IAX peers. The NAT firewall has port 4569 mapped through to the asterisk server behind. But, the natted server is almost permanently unreachable from this non-natted server, even though, the non-natted server is almost permanently _reachable_ from the natted server. Details are below

I'm going to try and lay out all the relevant information I have here in this one post. I can provide more info if necessary. ISSUE 1: Office A routinely looses connection to Office B. When typing IAX2 Show Peers, it will show as Unreachable. I issue IAX2 Reload and it will work again for 1-3 days (haven't narrowed the time down yet). My theory is that the DSL at Office2 is changing

Hi to everybody, My IAX is not working, When I type reload IAX it returns me: AsteriskSlave*CLI> iax2 reload == Parsing '/etc/asterisk/iax.conf': Found == Parsing '/etc/asterisk/users.conf': Found [Aug 26 10:05:04] NOTICE[18078]: chan_iax2.c:13546 set_config: Ignoring bindport on reload [Aug 26 10:05:04] NOTICE[18078]: chan_iax2.c:13610 set_config: Ignoring bindaddr on

I've got IAX2 setup between two servers with this config: I have two servers on a switch: asteriskm is 192.168.0.160 and asterisk1 is 192.168.0.161 asteriskm has a Sangoma T1 card in it. I want to route calls from asteriskm to asterisk1 which will run an AGI IVR for the call. Config is below, but my problem is that 90-95% of the time when I start asterisk on the two servers I get the

Hi, if I change Iaxphone settings to qualify=yes it says it's unreachable. Can iax2 clients be monitored with qualify option ? Is this problem related to iaxphone ? Anyone sucessfully using iax qualify feature ? Regards, Rob.

I donwloaded two IAX Clients (firefly and IAX phone) and they did register with *. It would make authenticated calls, but wouldn't actually register with the server. When I start the IAX Client the CLI show me the message: -- Registered '2004' (AUTHENTICATED) at 192.168.199.69:4569 After 5s: May 21 17:24:41 NOTICE[1133742896]: chan_iax2.c:5035 iax2_poke_noanswer: Peer

Dear, Kindly guide with the 2 issues mentioned below *#1* - *Host unreachable 0 last qualify 0 (only in 3G**)* I am trying to use SIP client over 3G. It registers and call can be initiated from the client but it can't receive call; cause *asterisk sever *marks it as unreachable immediately after registration. "[2014-10-08 14:32:47] NOTICE[1610]: chan_sip.c:29596 sip_poke_noanswer:

I have 4 asterisk servers which are "Friends" and each one has an account for termination. A total of 5 peers each. Currently, the setup is as follows ========iax.conf========= [FriendName] type=friend context=server_friend secret=donttell host=friend.dyndns.com qualify=750 ===================== In the past i would also use a register => and set host=dynamic, but the registration

I've turned on debug in a (IAXComm based) soft phone. I see the phone sending pings to *. I see * getting the pings. For some reason, with iax2 show debug, I never see any response on the console from *. However, the phone shows a response with INVAL. Seems like an odd response to a ping request. I believed it should get an ACK. Is that wrong? If I should get an ACK, what could I have messed

All, I have an issue with IAX that I can't comprehend. Approximately every eight minutes my servers go unreachable. They stay unreachable for exactly 10ms. I have two servers running IAX and it happens on both servers simultaneously. I have searched the archives and see similar issues, but not the exact same one. I am on the current CVS stable version of *. Also, during IAX calls,

I'm having a problem configuring asterisk to send incoming calls to Firefly. I can make outgoing calls from firefly through asterisk without any problems at all. The firefly client does this when it's on the same IP subnet without a firewall, or from a NAT'd environment. Can anyone tell me where I'm going wrong? Here is output from iax2 show peers: Name/Username Host

I just upgraded a very old Asterisk installation to the last 1.2.31 I can find in Asterisk.org site. Now for some reason my IAX clients cannot connect to the server. I can do a "iax2 show peer iaxmodem1" and I get this: * Name : iaxmodem1 Secret : <Set> Context : oficina Mailbox : Dynamic : Yes Callerid : "" <> Expire

Hi guys, I'm having a really strange problem, which I'm pretty sure has only appeared since my last upgrade (1.2.12.1) . It's about NAT and Qualify. I'm using Asterisk to register with some external SIP providers. However, they're always marked as UNREACHABLE, when they weren't before! A typical debug looks like this: hera*CLI> sip reload Reloading

Hello, I'm using asterisk for a quite long period, i integrated a lot of stuff to make it behave like any carrier class system, so users can: manage Call forward on busy manage Call forward on no answer manage unconditionnal call forward call back missed calls and a lot of such services that can be both configured by menus and dtmf or by web interfaces (PHP+SQL), in fact i recreated

Dear Royce; Did ur problem resolved? Because now I am facing same problem. It look like that it happens with IAX trunk only, but does not happen with IAX endpoints that registering (as trunk does not register, it sends the call directly). My initial analysis that one of the following can help to let the trunks talk: if there is an IAX endpoints registering to the machines, then trunk become