similar to: asterisk and norstar

Hi, I have a legacy Norstar system that I'm looking into integrating with my Asterisk setup. My first attempts have worked, which involves a Wildcard X100P FXO card in the * box connected to the Internal ATA (FXS port) on the Norstar system. Calling from SIP -> Norstar works fine, since the SIP caller initiated the call and generally will be sane enough to hangup the phone when

> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com]On Behalf Of Gary Reuter > Sent: Thursday, August 11, 2005 12:59 PM > To: asterisk-users@lists.digium.com > Subject: Re: [Asterisk-Users] PRI dropped calls w/ asterisk dropped > betweenpstn & norstar > > > I poured over my logs most of

To All; My current issues is a 5 second delay for call that is being transferred from the Norstar units to the Asterisk servers VIA a PRI. Is their anything that can be done to speed up the transfer on the Norstar. Below is my current phone config. < Norstar1 >----PRI----< Asterisk-1 >----IP-WAN----< Asterisk-2 >---PRI---< Norstar2> The Norstars are MICS 0x32 4.1

Does anyone know which signalling protocol works when connecting the output of a NT8B90AL Norstar ATA2 analog terminal adapter to an FXO card? (fxsks, fxsgs, fxsls?) I'm trying to add an Asterisk branch to my Norstar PBX as outlined at http://www.voip-info.org/wiki-Asterisk+Nortel. - Mike

Hi all, I've seen a couple of posts recently from people who are doing something with Asterisk and a T100P and a Nortel PBX. However it's not clear exactly what they are doing. Does anyone know if it's possible to use a T100P or T400P as a DSX-1 interface to connect to a T1/PRI CO module in a Nortel PBX? We have a Nortel Norstar Modular ICS PBX and I'd like to plug its CO

I'm attempting to use an asterisk box with a Digium TDM01B as voicemail for an existing Meridian/Norstar PBX with an ATA-2 adapter. We're having problems where hangup is not always (but sometimes) detected. It's not detected probably 70% of the time or more. (The users transfer callers to an extension--caller then has to navigate a menu to get to the appropriate user). After

I am currently working on an Asterisk test system, and will be presenting a demo to the Board of Directors tomorrow night. I want to make sure I have all of my ducks in a row. The Asterisk system will be used to replace a Norstar MICS. The location has two PRI's coming in, with a few hundred DIDs. I know how to make * use the DIDs incoming, and I know how Nortel uses the DIDs. Now for the

Hi, I dropped an asterisk server with a TE405P between a Norstar Meridian PBX and it's PRI PSTN connection. Everything seemed to work fine using a pass-thru-type dialplan configuration... except now we've realised that outbound calls to celphones get dropped upon connect, but not on every call (almost always the first try, but not the second). All other calls to non-celphones had no

I have a PRI link up and running between Asterisk and a Nortel Norstar MICS v4.1 . I'm having a problem getting the textual Caller Name across the link from Ast to Ns, however numeric Caller ID arrives and displays fine. From Ns to Ast both elements come through fine. I'm forcing dummy values for testing using: exten => s,1,SetCIDName(Test) exten => s,2,SetCallerID(1234561234)

I've noticed a problem with calls to Hangup when talking to my Norstars over channelised T-1 E&M trunk lines - it's been present since I started to fiddle with Asterisk last December and it's still present in 'Asterisk CVS-HEAD-08/13/04-10:37:13'. Specifically, when a call is connected to Asterisk from the Norstar DTI card to my T100p I get the following conditions

All good information, thanks. However this is private network between Asterisk and a Norstar MICS about six feet away. So I'm holding both ends of the link. :-) > -----Original Message----- > From: David Troy [mailto:dave@popvox.com] > Sent: September 16, 2004 4:57 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: [Asterisk-Users] No Caller Name

Unfortunatly no on both counts. The arrangement right now has: PSTN Trunks & Stations <-> Nortel Norstar#1 <-CT1-> Asterisk#1 <-IAX2-> Asterisk#2 <-CT1-> Nortel Nortstar#2 <-> Stations The Asterisk boxes provide Voicemail to their sites Norstars and intersite calls over IAX. Local Voicemail works flawlessly at each site but there have been reports of PSTN calls

I'm running asterisk 1.2.8. I would like PSTN inbound calls to do the following: 1-once PSTN callers enter their desired extension; they have to record their name 2-recording then announces that it is trying to locate the user 3-asterisk calls local extension and announces callers recorded name 4-local recipient user can choose to take the call, send it to voicemail or transfer it to

Hi, I'm trying to get my X100P to Dial the following sequence to gain access to speed dial numbers on my Norstar PBX that the X100 is connected to... [FLASH] [*] [0] [22] (where 22 is the speed dial number) But so far I've had no luck, with the following extension:- exten => 922,1,Flash(${DIALOUTANALOG}) exten => 922,2,Dial(${DIALOUTANALOG}/*022) exten => 922,3,Congestion

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48

I have Asterisk setup with two PRI's one going to my telco and the other going to a Norstar Meridian system. The Norstar Meridian is sending a BTN number that needs to be passed to the Telco. Is there a way to pass the BTN as a variable in the dial plan? Like CallerID(num)? What is the variable for BTN if so? Many Thanks. -- *** Forrest Beck IAXTEL: 17002871718 jonforrest.beck@gmail.com

Aloha, I have a Cisco Gateway the is functioning as my SIP Gateway to the PSTN. I have an Asterisk box, RC2 with a for port FXS card providing dialtone for a Norstar Key System. I have it working so when you press a line key on the Norstar you get dial tone from the Asterisk box. The user has to dial '9' then they can dial there number which is sent to the Cisco GW via SIP and the call

I am trying to integrate a Nortel Norstar system with an Asterisk service using a TDM04B card (4 fxo). So far everyting works from Asterisk to Nortel. The problem is when someone dials from the Nortel PBX to the Asterisk server. Asterisk answers the call and provides a dialtone (with DISA) but appartently the DTMF tones are not passed to asterisk and the call cannot proceed. This only

Sorry, I know it's OT, but does anyone know of a relatively inexpensive headset that is compatible with the Cisco 7960? I've tried the headset off Norstar phones, doesn't seem to work with or without the amp. ------------------------------------------------------------------------ | nate carlson | natecars@natecarlson.com | http://www.natecarlson.com | | depriving some poor

The last post I saw regarding this was June 2003 (before my time with *, I started in September): http://lists.digium.com/pipermail/asterisk-users/2003-June/013324.html Is there any support for Q.SIG in * at all? The Norstar MICS uses a MCDN (Meridian Customer Defined Network) key to enable the "SL1" protocol which from everything I've been reading is just Q.SIG. This protocol