similar to: INVAL Messages

Displaying 20 results from an estimated 1000 matches similar to: "INVAL Messages"

2006 Oct 18
0
IAX2 thru NAT problem
Hi people, i have problem with IAX2 between two asterisk PBX. When i try call some number i get "INVAL" packet, but when i try call same number via OpenVPN (is between this two asterisk) call is working fine.So i debug communications and here is my opinion ... Schema of connection: Asterisk1 -> ADSL router with NAT -> INTERNET -> Asterisk2 A)Calling directly via public
2009 Oct 02
1
IAX2 Call rejected, CallToken Support required
Hi All, I am using Asterisk 1.4.26.2 and I am getting the following problem making connections to this server. My other servers are Version 1.2.x which have no problems and this 1.4.26.2 server can call the other 1.2.x servers. The error is: chan_iax2.c:4251 handle_call_token: Call rejected, CallToken Support required. If unexpected, resolve by placing address 192.168.25.250 in the
2006 Oct 27
4
IAX2 show peers - description
Hi people, pls does anybody know what "(T)" and "(D)" letter means? server3*CLI> iax2 show peers Name/Username Host Mask Port Status SERVER1 xxx.xxx.xxx.xxx (D) 255.255.255.255 9785 (T) OK (29 ms) SERVER2 xxx.xxx.xxx.xxx (D) 255.255.255.255 4569 OK (95 ms) 2 iax2 peers [2 online, 0 offline, 0
2006 Nov 20
1
Call-limit
hello all, isit possible to do sth. so that if the sip-phone is in use and a call is incoming that the caller gets a busy signal? coz i wan to have the incoming party get a busy signal if i'm at phone. regards rene -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061120/6f438f28/attachment.htm
2007 Jan 12
4
Nat Question
Hello all, iam setting up an asterisk box behind NAT to get SIP calls from outside or internet. In that eschema i can setup SIP calls but, while from the outside nat people can hear me, Im unable to listen anything behind NAT. Out of firewalls settings( I checked this to port fowarding) what can i do to get this working fine?. Thanks G.
2010 Nov 18
2
IAX2 and INVAL packets
Is anybody here familiar with the meaning of INVAL packets for IAX2? Every few days I get a dropped outgoing call in the middle of the conversation (the outgoing call has been connected for few minutes) when an incoming call comes in. The log reads the following when this happens: [Nov 17 15:25:04] DEBUG[5138] chan_iax2.c: Immediately destroying 2963, having received INVAL [Nov 17 15:25:04]
2003 Aug 06
0
Intermittant IAX Call Failures
I was wondering if anyone had seen this problem before and/or could offer any insight into what the trouble might be: I have an Asterisk machine that it set up as a mutual friend with another one (in another state... about 150ms away). Calls between the two fail to get established approximately 50% of the time. When a call works, everything is fine. When one fails, however, I see a large
2003 Mar 31
2
iax problems
I'm having some trouble with placing some iax calls over an openvpn: Setup A is a 1.8GHz Celeron, T100P attached to a Zhone Zplex. Setup B is a 266MHz P2, T100P attached to a Zhone Zplex. Setup C is a 700MHz P3, T100P attached to an Adtran TA 750. Setup D is a 233MHz Pentium, with an X100P. Setups A and B are on the same physical network. IAX calls routed between them work fine. Setup D is
2010 Nov 25
0
IAX inbound failing
Hi, I'm testing an upgrade from 1.4.18 to 1.4.37 in a VM prior to putting it into production. Ive done this by installing 1.4.18 onto the VM, putting my config files in place and then installing 1.4.37 over the top (which is what I'd have to do on production). I've found a few issues in the config files, but nothing I couldn't handle until... I hit inbound IAX issues. My
2007 Jun 07
0
IAX-configuration
Hi all I have a network with nodes with different network-interfaces (e.g. node17 with interfaces A and B and node18). Asterisk listens to 17.A, 18's DUNDi knows 17 by knowing ip B. When I start a DUNDi request from 18 to 17 I get a response from A via B. So B knows that the number can be reached at 17.A which is correct. A ----------- B ----------
2006 May 25
2
jitterbuffer causes flaky IAX2 incoming connections?
I've been having problems with incoming IAX2 calls - some work, but a large fraction are answered with "dead air" or disconnects from my IAX provider. Disabling the jitterbuffer seems to eliminate the problem (so far)! Has anyone else seen this? I'm using 1.2.6, but I'm not sure what my provider is using. A snippet of the a failed incoming call IAX2 debug is attached
2017 Oct 11
3
TargetRegistry and MC object ownership.
Hi All, While trying to put together an MC-based assembler the other day, I again encountered MC's non-obvious memory ownership rules. The most egregious example of these is MCObjectStreamer's destructor: MCObjectStreamer::~MCObjectStreamer() { delete &Assembler->getBackend(); delete &Assembler->getEmitter(); delete &Assembler->getWriter(); delete Assembler;
2004 Dec 14
0
Codec "Uknown" with IAX connection
I am having some problems getting TelIax service to work with *. Outbound calls work just fine. When I try an inbound call the phone rings and there is no audio. Upon further investigation "iax2 show channels" indicates that the codec is "unknown" The provider confirmed that they are set for ulaw and so am I. Does anyone have an idea what could be causing the codecs to
2003 Nov 13
2
IAX trunk monitoring
I have an issue where * tries to route a call over IAX to another server even if the server is down. I have included the relevant entries from my iax.conf, extensions.conf, and some debug output. If someone could tell me what I have configured incorrectly, I would appreciate it. Thanks, Stephen -----------iax.conf on voip2---------- [voip1] type=friend username=voip1 host=x.x.x.x (ip
2005 Aug 07
1
Unable to connect to FWD
Hi, My asterisk server is behind firewall and i am trying to connect to FWD. i hv configured as mentioned in this link http://www.freeworlddialup.com/advanced/iax. i am able to register my server with FWD. But when i dial 393612, i always get 'No one is available to answer this time, try again later'. I hv portforwarded tcp 4569 and 5060 from my firewall to my asterisk server. Any idea
2005 Jan 24
2
PrivacyManager not Working
I have been having problems getting PrivacyManager to work correctly. Right now I am running the 1/21/05 CVS but I have been unable to get this to work on asterisk-stable either. You can see from the debug below that the inbound call is arriving via IAX2 and both the CALLING NUMBER and CALLING NAME are both set as "Unavailable". However, PrivacyManager executes and determines that
2018 Dec 12
2
[virtio-dev] Re: [PATCH v5 5/7] iommu: Add virtio-iommu driver
On Fri, Dec 07, 2018 at 06:52:31PM +0000, Jean-Philippe Brucker wrote: > Sorry for the delay, I wanted to do a little more performance analysis > before continuing. > > On 27/11/2018 18:10, Michael S. Tsirkin wrote: > > On Tue, Nov 27, 2018 at 05:55:20PM +0000, Jean-Philippe Brucker wrote: > >>>> + if (!virtio_has_feature(vdev, VIRTIO_F_VERSION_1) || >
2014 Sep 12
1
[virtio-dev] [PATCH 2/2] virtio-gpu/2d: add docs/specs/virtio-gpu.txt
>> Can the host refuse due to lack of resources? > > Yes. virtgpu_ctrl_hdr.type in the response will be set to > VIRTGPU_RESP_ERR_* then. Current implementation does that only on > malloc() failure, there is no accounting (yet) to limit the amout of > memory the guest is allowed to allocate. We do probably need to work out some sort of accounting system, it can probably
2014 Sep 12
1
[virtio-dev] [PATCH 2/2] virtio-gpu/2d: add docs/specs/virtio-gpu.txt
>> Can the host refuse due to lack of resources? > > Yes. virtgpu_ctrl_hdr.type in the response will be set to > VIRTGPU_RESP_ERR_* then. Current implementation does that only on > malloc() failure, there is no accounting (yet) to limit the amout of > memory the guest is allowed to allocate. We do probably need to work out some sort of accounting system, it can probably
2006 May 16
0
iax2 disconnect problem
Hi, I'm using asterisk 1.2.7.1 and somehow my iax trunking is getting these problem :S. Sometimes iax acts weird and start to drop calls randomly and give these at the log: May 16 13:44:22 DEBUG[5264] chan_iax2.c: Immediately destroying 6, having received INVAL May 16 13:44:22 DEBUG[5264] chan_iax2.c: Immediately destroying 6, having received INVAL May 16 13:44:22 DEBUG[5264]