Displaying 20 results from an estimated 10000 matches similar to: "Tellabs and a PRI"
2006 Jan 21
2
Tellabs 2572 EC Photos here.
Hello Dan,
Have a look at this link:
http://www.adcomcorp.com/asterisk/tellabs
I got those pictures up there, may be of help. In essence, 1 pair is
either a tx pair or an rx pair.
If I recall, Orange and Green should be one side, and blue brown should
be the other side.
I tried to upload them to the wiki (even 40% size) but they didn't show
up for some reason...
Files are large on the
2006 Feb 15
2
Software E.C. Along with Tellabs
Since putting my Tellabs EC into place around 2 weeks ago, the echo
problem has almost been eliminated. Reports of some very faint echo,
but everybody is happy.
My question is, if I were to also turn on the Asterisk Software EC,
would this remove any residual echo that may make it past the Tellabs
Hardware EC.
Thanks,
Doug
2006 Jan 12
2
Adit 600 and echo
I'm having issues with echo.
My setup is Polycom IP501 phones connected to an Adit 600 via T100P. 13
Lines going to the Adit.
All echo so far is on the local side (Employees hears own voice, but
only on some calls).
Watching the channel with ztmonitor, I notice that TXGAIN is pegged out
most of the time. RXGAIN is anywhere between 45 and 60%.
Is it safe to assume that playing around
2006 Jan 20
1
Hardwiring a Tellabs echo canceller - help req
Hi All, Greg has been a huge help getting me going with this tellabs echo
can, but I'm still having some problems getting it to work... I suspect I
wired it up incorrectly, so I thought I'd see if anyone can point me in the
right direction. Digium tech support pointed me to this doc for a standard
T1 cable:
http://www.arcelect.com/RJ48C_and_RJ48S_8_position_jack_.htm
which looks like it
2006 Jan 09
1
Tellabs echo can, can someone wire mine up for $?
Hello All,
I have a tellabs 2572 EC, and I was wondering if anyone with experience
can wire this up for me...
I have the proper tools and info, but not the time. It's easier to send
it out and get it done. I know kb1_kanobe originally started the wiki
thread, and rather than risking the card, would it be possible for me to
send it out to him, have him do it, and send it back?
Not to say I
2004 May 20
1
Tellabs 2572 Configuration Advice?
Can anyone share any advice / documentation on how to configure a Tellabs
2572 T1 echo canceller? I connected one between a T100P and an Adtran
TA750 FXO/FXS channelbank, but when echo cancellation is active I get
a LOT of snap-crackle-pop (and other problems) on the line.
The 2572 has a bunch of configuration options and they're impossible to
guess without documentation, which I cannot find
2004 Jul 22
1
Echo Canceller Wiring (Tellabs.. HOWTO..?)
Hello,
I have been researching Echo Can's for a while now, and wanted to post
this out to the list to solicit feedback (and if my assumptions are
correct, hopefully help others out)...
If anyone out there knows anything about wiring up an Echo Can, and my
outline below is incorrect, please let the me/list know..
I have posted the Documents I received from Tellabs at:
2006 Feb 06
7
BAD/GOOD Echo Cancel
>
> hi,
>
> How good or bad is the EC in Asterisk?
>
> Can anyone prove that it works at all and what it's limitations are?
>
> I ask cause I have some problems with this myself which variate from
> call to call, and I see from others that Echo Cancel is a quite common
> topic.
>
> Jan
>
>
I have installed systems that had absolutely no echo
2006 Feb 11
1
TE411P Really Bad Echo ORION
The Orion echo canceller is just ok. The Tellabs units work just as well if you don't mind 10 mins of soldering.
I have the orion running with an adit 600 and a TE110P. Echo cancel is fairly good, but I have loads of problems with DTMF digits.
-Darren
________________________________
From: asterisk-users-bounces@lists.digium.com
2005 Jun 24
4
Tellabs Echo Canceller
I am getting ready to experiment with the Tellabs 2752 echo canceller. I have a 255D shelf (and power supply), but am struggling a little on connecting the echo canceller to a PRI.
The shelf has 4 25-pair amphenol connectors. The two on the line side are marked "Receive In" and "Send Out". The 2 connectors on the drop side are marked "Send In" and "Receive
2006 Jan 12
2
SIP phones unbeatable echo
Hey all again, I'm wrestling with echo problems on our sip extensions. I've
set these items in zapata.conf but tweaking these values doesn't seem to
make much difference
echocancel=yes
echocancelwhenbridged=yes
echotraining=2500
rxgain=8.0
txgain=1.0
are there other settings that can help me tame this beast? Been searching
but not turning up anything that'll work here.
Thanks
2006 Feb 06
4
two tellabs 2572 echo board in a 253c mounting assembly?
Anyone gotten two of the 2572 echo canceller cards to work in a 253c mounting assembly? I can get one to work, but when I install two, one always fails. I've tried all my cards solo in the enclosure, on each side, and they all work properly when only 1 is installed, however, when I install two, one of them will come up, but the other always fails. Anyone know what might be causing this?
2009 Sep 02
2
DISA() fails to recognize dtmf where WaitExten() succeeds (DAHDI-PRI)
Is there any known reason that the DISA() routine should behave
differently than WaitExten() as far as recognizing DTMF tones? If
not, I suspect there's a bug here.
Try it yourself--two DID's on our PRI, numbers below let you test each routine:
It is my observation that some setups/phones DO and some DO NOT
express this variance.
--I could not show any variance on a sprint mobile phone
2012 May 04
1
Absolute cumulative curve with ecdf/stepfun?
Hi,
I have two variables ranging both from 0 to 1 (n=500 each).
Now I am interested in plotting them both in one plot (using ggplot2).
So far I used ecdf() (from an example I found with google) to get
values for the cumulatice distribution function which gives a relative
curve. I also want to do the same plot but using absolute cumulative
values instead of relative. Can that be done with ecdf or
2007 May 06
3
Channel Bank
Can someone recommend a good quality 24 or greater port channel bank?
Steve
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070506/e5896021/attachment.htm
2005 May 18
0
Tellabs Consultant Wanted
We are trying to install a Tellabs echo canceler on our T-1/PRI and
having no luck. We can't get the lines out of AIS/RED/BLUE alarm when
we put in the echocan.
We are looking for a consultant (near New Orleans) to assist us in
installing this device.
Contact John DeMajo <jdemajo@stirlingprop.com> at +1-504-858-7689
--Eric
--
Always do right. This will gratify some people and
2005 Mar 07
6
Tweaking AGGRESSIVE_SUPPRESSOR
Using TDM400's here and I have tried everything to cure the echo. I
have used the Milliwatt test from the telco and from asterisk to tune
RX/TX gain via a patched ztmonitor. What happens is I experience
midcall echo. I turned on aggressive_suppressor and it seems to do
great. The problem happens with misc. noise around the office will
cause it to mute the other end of a phone call while
2009 Sep 23
1
set choose.files directory?
Hi,
I've been trying to set the directory for choose.files as follows:
[R2.9.0 running on XP]
setwd("C:/Documents and Settings/2/Data")
getwd()
infile2 = choose.files(filters = Filters[c("txt","All"),], caption =
"Choose ECD datafile")
#<...do a bunch of stuff...>
It appears the working directory isn't updated until after choose.files()
2006 Nov 14
4
In the beginning-The first question.
List,
Im a Cisco certified Network guy with little telecom experience (BRI/PRI
at the time) so please forgive my terminology. I am showing interest
after the Network World SHSU October 4 article. We have 3 offices
(Hub-Spoke T1 Frame relay to the remote offices(Data & voice on separate
T)). Each office currently does their own thing for telecom. Our
Main(HUB) office currently has 14 channels
2006 Feb 07
2
Re: two tellabs 2572 echo board in a 253c mounting
30 says it's view only in the docs & I can't seem to change it, any other options?
> Option 30 allows to set Module Shelf Address/ID.