similar to: Trunk failover

Hi, how can I convert .wav files to .WAV: # file greet.* greet.wav: RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz greet.WAV: RIFF (little-endian) data, WAVE audio, GSM 6.10, mono 8000 Hz using 'sox'? Thanks -- Domenico Viggiani

Hi, I'm planning to install a new Asterisk server with a Digium TE410P card. Can I use Red Hat Advanced Server 4 (latest update)? Is this a good choice? Is recompiling Asterisk simple with kernel 2.6? Thanks -- Domenico Viggiani

Hi, I'm trying to edit an AMP-derived dialplan: the macro "dial" uses the AGI script "dialparties.agi" to find the extension to call. I'd like to drop this script: does anyone can explain me what is its main job? Thanks -- Domenico Viggiani

Hi, I'm trying my new Snom 360 phone (6.2 firmware) and I'm seeing that it doesn't register with the Asterisk 1.2.9.1 server after a reboot. I need to click "Re-register" in the web interface. I set: - Support broken Registrar: On - RTP Encryption: Off Any help? -- Domenico Viggiani

Hi, during gradual migration to Asterisk, I put Asterisk in front of a legacy Alcatel PBX: PRI PSTN <--> Asterisk <--> E1 cable <--> Alcatel PBX After successful deployment of VoIP phones, it's time to drop Alcatel PBX! I'd like to keep some of analog lines to support modem, fax and some older stuff. What's the best choice? A channel bank or a TDM2400P card? Can I

Hi, is there a RHEL4 RPM for the Festival text-to-speech system? Thanks -- Domenico Viggiani

Hi, calling a partner on the other side of a SIP trunk, call gets disconnected immediately after answer. This is the content of log file: Jun 14 16:25:14 DEBUG[14380] channel.c: Didn't get a frame from channel: SIP/cerved-out-6eba Jun 14 16:25:14 DEBUG[14380] channel.c: Bridge stops bridging channels SIP/232-2e41 and SIP/cerved-out-6eba Jun 14 16:25:14 DEBUG[14380] channel.c: Hanging up

Can someone explain me this message: "chan_iax2.c: Ooh, voice format changed to ..." Where can I find a list of numeric codes used to identify voice format? Then, sometime I get an infinite loop of messages like these: DEBUG[15015] chan_iax2.c: Ooh, voice format changed to 1 WARNING[15015] channel.c: Unable to find a codec translation path from g723 to alaw DEBUG[15015]

Hi, I'm actually using a slightly old version of AAH with Asterisk 1.2.1, because at first install it was perfect for my moderate knowledge of Asterisk. It is working well but I gradually introduced many changes to dialplan during normal use and now I'm feeling like in a straitjacket! Moreover I'd like to have the chance to upgrade Asterisk regularly. I have not the experience to

Hi, I have a IAX2 trunk between two sites (connected with an high bandwidth link) but sometime/often I get: chan_iax2.c: Auto-congesting call due to slow response and call is dropped (and routed on a PSTN link). In iax.conf, I have: [iax-out] username=iax-in type=peer trunk=yes secret=xxxxxxxxxxx qualify=yes host=xxx.yyy.zzz.32 auth=md5 Any idea? Perpaphs is due to

Hi, I have a lot of GXP-2000 phones not registering with Asterisk server. After two days of attempts, it seems that problem is due to the fact that phones and server are not on the sme network. Do you know if this is known issue? -- Domenico Viggiani

Hi, during tests, I configured different SIP accounts on the same phone. Now I see this 'sip show peers output': Name/username Host Dyn Nat ACL Port Status 259/259 10.97.1.19 D 5060 OK (8 ms) 232/232 10.97.1.19 D 5060 OK (7 ms) where both extensions are registered and have the same IP. But now I have only one extension

Hi, using Sangoma drivers: - doing 'lsmod', I see: zaptel ... wanpipe,wctdm24xxp,wctdm,wcfxo,wcte11xp,wct1xxp,wct4xxp,tor2 I'd like to avoid loading all these modules. What have I to do? - do I need to have 'zaptel' startup script under /etc/init.d ? Thanks -- Domenico Viggiani

Hi, I have '*1' in my features.conf file and I'm facing with a serious problem: - A and B are engaged in a call - C and D are engaged in a different call and decide to record their conversation hitting *1 - at the end, A and B are able to see C/D call recording using ARI with their user/pwd!!! Where is the problem? Asterisk or ARI? Thanks in advance -- Domenico Viggiani

Hi, I just migrated my Asterisk installation from 1.2.1 to another server with 1.2.8. Among a lot of things, I copied the whole content of /var/spool/asterisk/voicemail/default directory. All is OK but now I'm not able to see MWI indication for new messages on all my Grandstream GXP2000 phones (before migration, it worked). Peraphs do I missed something? Thanks -- Domenico Viggiani

I already posted this message but I had no answer. Sincerely, I think it is a bug and I'd like to hear developers on this. Platform: - HP-UX 11.00 - HP C/ANSI C Compiler (B.11.01.06) Copying a (large) directory structure from a NT share, interactive command: # smbclient //machine/share password >prompt >recurse >mget * fails to copy 76th, 115th, 154th file of

I'm posting this message in charge of Denis MARS (France), because he is not a subscriber of teh list and I worked with him about the same problem. Domenico Viggiani ---------------------------------------------------------------- Hello, I worked on this problem since three weeks and now i really give up. Clearly i can't go further without your help. I hesitate to send you this bug

Hi, I'm unable to pickup a call (*8) directed to a SIP phone from a IAX2 phone. Is it normal? I don't see ant pickupgroup/callgroup setting in iax.conf... -- Domenico Viggiani

I'm trying to get an IAX trunk to failover to a local trunk it the trunk is down. This is what I've been working on: [macro-forward1]; exten => s,1,Dial(IAX2/192.168.1.1/${ARG1},20) exten => s,2,Goto(call-${DIALSTATUS},1) exten => s-CONGESTION,1,Dial(LOCAL/${ARG2},20) exten => s-CHANUNAVAIL,1,Dial(LOCAL/${ARG2},20 ;end macro-forward1 exten =>

Hi, I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (only one until now!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR