similar to: sangoma unicall m2rfc

Guys. Ive been testing how to receive faxes using TDM400P cards and so far, after playing with gains, echocancell and echotraining on zapata.conf.. Ive ha dno luck, faxes come in as garbage or broken or with blank lines. Anybody has successfully done this? Any tips.. Also I have some ideas: 1. Is it really possible to get fxes on a fax machine using ATAs like the sipura 2002? Even using ulaw

Hi Guys! I have a problems with some sipuras 841 and asterisk 1.0.9. Im using 841 with asterisk 1.0.9 with a digium card (single e1 span) with steve's unicall. Everything compiled fine and in fact I can make and receive calls but I have a problem with bad sound when the sipuras call the outside E1's lines. I can listen to the caller without problems but they heard me with a choppy

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Guys. I have a te100p with unicall and an E1 and Im having problem with DTMF tones but the weird thing is, I only have problems sending the tones to certain phone numbers, anybody seen this behavior? Asterisk shows on the console the dtmf tone been pressed but seems the other side is not getting them, and this just happens with certain phone numbers, not all.. Any clues(tips?

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hi all, Anyone have an idea which version of spandsp, libunicall, libmfcr2, libsupertone, app_rxfax/app_txfax and chan_unicall I should use for the latest asterisk 1.2? Would that be the ones listed below? http://www.soft-switch.org/downloads/spandsp/spandsp-0.0.4pre4.tgz http://www.soft-switch.org/downloads/snapshots/spandsp/test-apps-asterisk-1.2/

Hi all, I have Asterisk 1.2.10, zaptel 1.2.7, spandsp-0.0.3pre22 compiled, and a Sangoma A101, and when I make a call I get this: Jan 8 13:04:06 DEBUG[12252]: chan_unicall.c:2000 unicall_exception: Exception on 19, channel 1 Jan 8 13:04:06 WARNING[12252]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 1101 [1/ 40/Seize /Idle ] Jan 8 13:04:06 WARNING[12252]:

I am having a problem trying to get a Sangoma A101 to work with Unicall. I have installed the sangoma drivers and everything seems to be well but when I try to run ztcfg I get the following error: CAS signalling on span 1 conflicts with HDLC with FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101

Hi everyone! I'm having some issue trying to place calls with asterisk connected to an E1 R2 from Telmex Argentina. The other E1 port is connected to a Meridian which also uses R2 protocol. Calls sometimes fail with different error messages such as: Unicall protocol error 32773, 32772, 32769. Some other calls fail saying: Far end disconnected(cause=Destination out of

I am having a strange problem with an asterisk servier using R2 Unicall in Mexico. Most calls go through fine but some of them give me an error like this: -- Executing Dial("SIP/86-db41", "Unicall/g2/014448343600") in new stack -- Called g2/014448343600 Feb 9 21:44:39 WARNING[23069]: chan_unicall.c:2644 handle_uc_event: Unicall/2 event Dialing Feb 9 21:44:45

Hi all, I have begun the release of my MFC/R2 protocol software. At http://www.opencall.org/installing-mfcr2.html there are instructions for installing what I have released so far. This is the MFC/R2 protocol software, and a test program. The software to interface Asterisk to the MFC/R2 code will be released shortly. It used to work, but it hasn't been touched for a while, and Asterisk

Hi all I have MFCR2 successfully installed but seems to get warnings a s seen below when I start asterisk. Am running on Redhat 9. Asterisk Ready. *CLI> Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 far_unblocking_expired Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 local_unblocking_expired Dec 20 08:40:38

Hello, i'm using asterisk 1.4.9 in fedora 7, i was compiled its with this package: libpri-1.4.2 asterisk-1.4.9 spandsp-0.0.4 unicall-0.0.5pre1 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 zaptel-1.4.4 i'm using a E1 pci card with R2 but they not work, when I start the asterisk its generate this log: [May 12 08:53:24] WARNING[30814] channel.c: No channel type

Hi, I'm running Asterisk 1.4.2 on a Debian GNU/Linux and a Digium TE210P card. I have one E1 with MFCR2 Signaling. I compiled asterisk + libunicall, and I can make calls over E1, but can't receive. Here the CLI when I make a call: -- Executing [006191642208@ps5:1] Dial("SIP/23-081cbc40", "Unicall/g1/91642208|50") in new stack -- Called g1/91642208 [May 14

Hi every one . There are any out there that have a unicall deploy working without problem ? Can give me some tips or referenece about his config ? Regards

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Im glad to let you know that finally I invested some time to make work Unicall in Asterisk 1.4, I must say not much testing could be done since I have no hardware available ( cards, servers ), however a friend was able to test it with a couple of calls with success, I need you to test this and report some feedback. The sources are available in: http://moy.ivsol.net/unicall/soft-switch/r1b1/

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but