similar to: SIP codec preference order ineffective

Hi i am trying to do the same thing: receive a call from a cisco callmanager and forward it to a SIP user. Asterisk is compiled with h323 support, and is configured as a gateway in the cisco callmanager. h323.conf: [general] port = 1720 bindaddr = 193.x.x.x ; this SHALL contain a single, valid IP address for this machine allow=all extension.conf: exten = 3298,1,Answer exten =

Hi list! My problem: I have three extensions in my Asterisk 1.8.30.0 and they have a voicemail. On two of these numbers the voicemail works without any problem, on the other it doesn't... I get this error: [Oct 17 17:01:29] WARNING[14700]: channel.c:5254 set_format: Unable to find a codec translation path from 0x100 (g729) to 0x2 (gsm) [Oct 17 17:01:29] WARNING[14700]: file.c:957

Hello. I have a codec problem to send calls from a SIP device to a H323 gateway. First I'll explain the scenario: - Asterisk 1.2.1 - The SIP phone can use any codec I want. - The H323 gateway can only use g729 (cause it's not under my administration) - SIP phone has g729 configured, so my asterisk doesn't need to "transcode" (I don't have licences for g729) - sip.conf

Hi All, I have this codec problem, I use "gsm" in my iax.conf file and in teliax settings also, but the error is still appearing as below. please help me. Kumara Starting simple switch on 'Zap/1-1' -- Executing Dial("Zap/1-1","IAX2/kumara@teliax/01194777070239|30|tr") in new stack -- Called kumara@teliax/01194777070239 -- Call accepted by

Hi Sir, We have integrated Skype with Asterisk (skype user id:- rexesbposolutions). Each call which is coming to skype account is getting transfered to Asterisk Queue. It has following two cases: case 1: When we call from normal skype account to skype account (rexesbposolutions), everything is working fine. case 2: This skype account (rexesbposolutions) has been assigned with a online virtual

Hi, I copied a setup from an older 1.8.5 installation to an 11.15 installation, and I'm having problems getting call files to work. Here is the extension setup I'm using: [outbound-swift] exten => _[a-zA-Z].,1,Answer exten => _[a-zA-Z].,n,Playback(AAA/check_ip_failure) ;exten => _[a-zA-Z].,1,Swift("${EXTEN}") exten => _[a-zA-Z].,n,Goto(1) [mis-phone] exten =>

set_format: Unable to find a codec translation path from ulaw to g729 Both endpoints are PAP2 set to G711 only I have 1.2.17 on Suse 10.1

Greetings! to all Now, with some hard time and help from many genurous people's in the list, I have come to this point with my TDM20B card & my teliax's IAX2 account. I hope someone may help me with this issue mentioned below. I have already selected my codec as gms in my iax.conf as well as in teliax's "my account page" but still i have the same error when I attempt

Hi i'm trying to connect to the PSTN in the following way sip ATA -> * -> gnugk -> Cisco AS5300 -> PSTN I'm using asterisk CVS-HEAD-06/01/05-14:33:15 running over RH EL3 Asterisk-Oh323 0.7.2 pre1 Open H323 v1.13.5 pwlib v1.6.6 and I'm having a lot of trouble, gnugk and * both have public ips and are not behind any type of firewall, the sip ATA is behind a firewall and

Hi all, I install the last version of Asterisk and I tried to send faxes, but nothing works. Here is my configuration: Analog Fax <----> IP <----> Asterisk <----> IP <----> Patton M-ATA <----> Analog Fax 2 I tried Analog Fax 2 -> Analog Fax but nothing works!! In the Patton configuration I put G711 and no silence suppression. In asterisk I have

Hi, I have just signed up with Voxee.com and have attached my Asterisk server to dial them via IAX2. Below is the start of the log which dials the number and promply hangs up when the call is answered, with the logs saying that the channel is not compatiable. I have traced this down to the g.729 codec which I don't have installed. Any ideas on how to force that the codec not be used?

I am trying to create a %100 g729 (with no transcoding) system (using a Soekris, of course). I am running AstLinux with the native sounds, g729 is the only codec allowed, %100 SIP (g729 only allow=) - I think I am covering all of my bases. I have only "format=g729" in voicemail.conf. On an incoming call to a mailbox, everything goes well until recording the message. When the

I am having a problem with one of my callers who is using either g729 or alaw.  I can do alaw but not g729 so asterisk should negotiate alaw right?  In fact from the sip debug it looks like it does, but then I get the dreaded "channel.c:5630 set_format: Unable to find a codec translation path: (g729) -> (alaw)" and the call hangs up.  Why? Last minute thought: Is it possible that

Hi folks, how could I play an announcement to the calling party as soon, as the called party picked up. I would like to deploy an asterisk in an environment, where a premium rate support-number is offered to customers which do not want to pay a monthly support contract. In Germany, you are commited by law to announce the cost per minute of a premium rate number at the beginning of the call. So,

I'm sitting here with my dunce cap on. My weak excuse is that I haven't ever played with g729 before. I have a Sipura 841. I have the phone config set to use g729. Its appropriate sip.conf entry, and the IAX stanza for my ITSP all set to disallow=all, allow=g729. But as soon as I dial, I get a complaint from the server: -- Call accepted by 66.225.202.72 (format g729) --

Hello, I am having a Mac 10.6.4 (Snow Leopard). I have compiled and built Asterisk 1.6.2.9 and Festival 2.0.95:beta on my machine. Asterisk is working fine with SIP channels without Festival. I have written following context in extension.conf: [connect-to-me] exten => s,1,Answer Exten => s,n,SayDigits(?1?) exten => s,n,Festival(hello john) exten => s,n,Hangup I use call files to

Hi list! I have 4 numbers on my Asterisk 1.8. 3 work perfectly, the 4.th not. I'm not sure, when it finish to work, since a month ago it runs without any problem... Well, if I will be called on this number I can't hear anything and in Asterisk I see these: [Jul 15 18:59:55] WARNING[8752]: channel.c:5060 ast_write: Codec mismatch on channel SIP/00493514977290-000001d1 setting write format

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,

Hi All, I have Asterisk 1.2.9.1 sending SIP calls to a Cisco 2620XM Router with a PRI card in it, handing off to a PBX and vise verse. Calls in and out are working fine except for DTMF from Asterisk to the 2600. DTMF from the 2600 to Asterisk is fine. Here are the Asterisk console warnings I get when I send DTMF from Asterisk to the 2600: == Forcing Marker bit, because SSRC has changed Jun

Hi all - I am using asterisk 13.27.0 with Linphone. I turned off all codes on linphone except the one I want to try. For example: opus and speex (so only one enabled at a time). Then did this same on asterisk for the linphone extension. disallow=all allow=speex (for example). Then I place my call and the call fails. if I enable something like gsm, ulaw, alaw the call works fine. Why does the