similar to: DUNDi Docs

It seems that I am having a heck of a time explaining my attempts at distributing ACD Queues to the list. Here's one little problem, that's only a piece of the puzzle. dundi.conf: 180q => global_dundi_q_pbx1,100,IAX,dundi1:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q => global_dundi_q_pbx2,200,IAX,dundi2:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q =>

I have three Asterisk boxes. Each has the following in dundi.conf: 180net => dundi_local,0,IAX,dundi:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q => dundi_q_pbx1,1,IAX,dundi:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q => dundi_q_pbx2,2,IAX,dundi:${SECRET}@${IPADDR}/${NUMBER},nopartial 180q => dundi_q_pbx3,3,IAX,dundi:${SECRET}@${IPADDR}/${NUMBER},nopartial My iax.conf on all three

I'vce got three Asterisk systems here that I'd like to be able to place calls between with IAX. As usual, I've spent several hours playing with it, really getting nowhere. Asterisk is so mentally draining. Each system, pbx1, pbx2, pbx3, should be able to connect to every other. Do I need separate user/peers or can I combine them into a single user=friend for each system? if I place a

I have a weird situation. A polycom phone is configured to use system pbx1 as the primary outgoing 'proxy', followed by systems pbx3 and pbx2. All three systems have identical sip.conf files. The phone is registered on pbx1. I shut down the Asterisk application on pbx1. I make a call. The phone sends an INVITE to pbx2. Pbx2 sends back a 407 Proxy Auth message to the phone. The phone sends

Does anyone have any information on how to use DUNDi precaching? Mark Spencer made a post 2 years ago where he hinted it may be possible to configure DUNDi such that you could centralise your DUNDi registration info by using precaching, instead of having each DUNDi peer meshed with every other one... http://lists.digium.com/pipermail/dundi/2004-October/000189.html However, it seems that no

What's wrong with the Asterisk CLI history? When I exit the CLI, and re-enter, the last command in the history always defaults to 'stop now'. This is very bad, and it's caused accidental shutdowns more than once. Connected to Asterisk 1.2.9.1 currently running on hera (pid = 17399) Verbosity is at least 3 hera*CLI> A No such command 'A' (type 'help' for help)

Hi all, I am running to the following problem, when using the below dialplan to receive fax, everything works perfect till this line exten => receive,n,ReceiveFAX(${FAXFILE}): and then the following line cannot be executed, it's like asterisk can't go back to dialplan and continue, the good news is when i check what is received in my fax folder i find that the file is a valid one (not

Anyone out there have a functional DUNDi configuration using SIP for the inter-Asterisk transport? I've gotten it to work with IAX2, but if I change it to SIP it does not pass the call over even though it knows where to send it. Thanks. The contents of this email message and any attachments are confidential and are intended solely for addressee. The information may also be legally

Well, I've been dicking around with DUNDi for about 4 hours now. I have two systems that I am trying to get to peer with each other. Queries are working one way, but not the other. The server, pbx1, that is refusing to deliver any queries and logs what's below to the console. Why??? I've checked all the config files more times than I can remember. The 'RFC' for DUNDi at

Has anyone got any neat solutions for Asterisk .conf file revision control? We have multiple Asterisk boxes here, that we'd like to maintain a _mostly_ common set of conf files on. They aren't all the same though. There's subtle differences. For example, in sip.conf, iax.conf etc, the bindaddr setting is different. Dundi.conf is very different between each system. At the moment I

Hi, I have been headbanging with asterisk and Jack for a while, decited to ask other linuxists for an advice. The problem is that Jack is compiled from source (0.118) in /usr/local/, but menuselect says "XXX" for it (cannot enable it). I need jack... Otherwise I will inotify Monitor WAVs, what is bad :`( After installing jack from sources: Add system-wide

Hi Guys, i spent some time to figure this out (since i love how dialplan is written) but i decided to ask for your help guys. i have two asterisk servers one is 1.2 the other is 1.4, from 1.4 (pbx1) to 1.2 (pbx2) i can leave a voice mail without any pb, but from pbx2 to pbx1 it just hang up. in pbx2 extensions.conf: i am using: exten => 8029,1,Dial(IAX2/pbx1/${EXTEN},20,tTWwr) in pbx1, i

Hi Guys, i am using two PBX's i can call from pbx1 a cellphone tied to pbx2 that way: 1) use a phone in PBX1 2) call extension in PBX2 3) extensions in PBX2 ring to a cellphone (as this specific ext is tied to a cellphone) my questions now is : am i gonna be able to dial from an IPphone registered within PBX1 to a cellphone by using the Trunk (Zap or dahdi) of PBX2? anybody know

Hi Im trying to install my TC400B trans coder card when I do: modprobe wctc4xxp tail -f /var/log/messages says: May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Encoder' with 92 transcoders (srcs=0000000c, dsts=00000101) May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Decoder' with 92 transcoders (srcs=00000101, dsts=0000000c) May 13 14:56:36 pbx2

Hi Guys, i am using the following config in pbx1: register => pbx1:endopass at 172.16.200.175 <pbx1%3Aendopass at 172.16.200.175> [pbx2] type=friend host=dynamic trunk=yes sercret=password context=[default] deny=0.0.0.0/0.0.0.0 permit=172.16.200.175/255.255.255.128 in pbx2: register => pbx2:endopass at 172.16.200.176 <pbx2%3Aendopass at 172.16.200.176> [pbx1] type=friend

thanks John yeah, your approach is much siple, i've tried it but i'm not able do detect DTMF tones. it seems that on calls that i receive DTMF tones are handled correctly, but on calls generated from Asterisk to the world when the called side sends some DTMF digits they are not detected: -- Executing [s at macro-myconnector:1] NoOp("SIP/pbx2-000004b2", "") in new

Hi All, i want to make an extension from pbx1 able to tlak to another extension from pbx2 or use pbx2's trunk to dial outside calls. so i edited in both servers accordinally the iax.conf: register => pbx1:pass at 172.16.200.175 <pbx1%3Apass at 172.16.200.175> [pbx2] type=friend host=dynamic trunk=yes sercret=pass context=[default] ; i used the biggest context to avoid confusion as

Marcelo Terres wrote: > I noticed another different behaviour. > > In older versions, when I call rasterisk, I receive some informations > about it. Fox example: > > [root at pbx2 ~]# rasterisk > Asterisk 11.22.0, Copyright (C) 1999 - 2013 Digium, Inc. and others. > Created by Mark Spencer<markster at digium.com> > Asterisk comes with ABSOLUTELY NO WARRANTY; type

Hi, I am trying to understand why some of my call transfers fail. My scenario is as follows: Legacy PBX1 ---PRI (EuroISDN) Zaptel--- Asterisk PBX2 Step1: PBX1 extension 101 calls PBX2 extension 102 Step2: PBX2 extension 102 answers the call and transfers it to PBX1 extension 103 Step3: PBX1 extension 103 answers the call and transfers it to PBX2 extension 104 Step3 fails and extension 103

Hi. It is propbably a really naive problem, but I really couldn't find answer how to connect two Astrisks via SIP. I managed to do it via IAX without any problem. But this is a test installation and I would like to connect them via SIP. So I have two computers: pbx1 - 10.1.3.207 pbx2 - 10.1.3.204 pbx1 handles extensions 1xx and pbx2 for extensions 2xx. I would like to call user from pbx2 to