similar to: Auto dialer

Not able to get the auto dialer part of asterisk to work with the zap channel. It works great with the sip channel. Here is the call file and the CLI output Call File Channel: ZAP/G1/6144994925 MaxRetries: 3 RetryTime: 40 WaitTime: 2 Context: amaxx Extension: 36652 Priority: 1 CLI Output Connected to Asterisk SVN-branch-1.4-r57207 currently running on VoIP-PBX (pid

A friend asked me for help to auto-dial and play a prerecorded message for a political campaign. I've briefly googled auto dialer scripts but haven't seen one that really stands out. Are there any free or cheap auto dial solutions that you nice folks recommend? Thanks in advance. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, We would like to share our webinar about Auto-Dialer Business Model (Telemarketing). It is educational video which we made for our clients and now we are sharing it with you. http://www.kolmisoft.com/how-to-start-a-VoIP-business/webinars/ Enjoy. NOTE: This is not attempt to sell you anything. No product or service is sold/marketed in the video. Regards, Kolmisoft Team

Hi all- I have asterisk running on 2 systems, with four E1 spans each. Each system is connected to a (big) NT DMS-100 switch. For load testing an IVR system running on one of the asterisk systems, I'd like to use the other system to generate a lot of outbound calls under program control - on most or all of its channels simultaneously. All of the asterisk dialplan and agi programming

Dears; I am facing a problem in disconnecting the calls, it is related to the rtptimeout (disconnecting if there is no RTP packets from both sides). My Asterisk Box is behind NAT but there is a static real IP address at the ADSL router. We call from the Mobile to the PSTN analogue numbers which are connected to Asterisk Analogue card (the telephone lines are analoge), and then we dial the

Hello, I'm a newbie to the asterisk system. I'm trying to configure a dialplan so that when I use my IAXy it will prompt me with an IVR and then send me off to different things like dial and voicemail from that. I've tried various combinations but I can't seem to get it to work properly. Here is an example: [default] exten => s,1,Answer exten => s,2,Ringing It gives me

Hi All, I need help with integrating AVAYA 8300, the avaya can do outbound calls but cannot do inbound calls, im sending calls from sip to avaya using E1 ISDN line. My config was based on aspect dialer it's working with aspect but not with avaya. My config and error is below. zaptel.conf span=1,1,1,ccs,hdb3 bchan=1-15,17-31 dchan=16 zapata.conf group=0 context=avaya switchtype=euroisdn

I originally wanted to answer with something ... tzarit and kevit Readed probably before you invent rapid biz. I am asking to share any info /experience not your high spirit. Thanks for less trivial answer, G >On Wed, Oct 05, 2005 at 12:44:27PM -0700, Thameem Ansari wrote: >> I am using the inter asterisk trunking and the article in >> voip-info.org<http://voip-info.org>will

I'm running Asterisk CVS-v1-0-12/20/04. I'm using PHP with Manager API Here is the code: #################################################################### # Make call #################################################################### $socket = fsockopen($ask_db,"5038", $errno, $errstr, $timeout); if (!$socket) { echo "$errstr ($errno)<br /\n"; } else {

Has anyone ever tried to roll out a *66 auto-callback-redial feature on asterisk? I'm sure that implementing this for outbound Zap calls would be a nightmare, but what about something easier, like internal extensions? On my old Panasonic key system, it used to be such that, if the called extensions were busy, you could press 6 while hearing the busy signal, it would beep twice and hangup.

Hi all, I need help in disconnect supervision. Im running on AAH ver.2.5 at home with TDM400P with 1 FXO and 1 FXS (TDM11B). I have implemented DISA on AAH for origination (PSTN to VOIP bridging). I'm facing problems with disconnection supervision. My calls are not getting disconnected at times and it causes a lot of loss as the provider is charging me. After some serious study i have found

Hi all, I need help in disconnect supervision. Im running on AAH ver.2.5 at home with TDM400P with 1 FXO and 1 FXS (TDM11B). I have implemented DISA on AAH for origination (PSTN to VOIP bridging). I'm facing problems with disconnection supervision. My calls are not getting disconnected at times and it causes a lot of loss as the provider is charging me. After some serious study i have found

hi, do you have someone example of http://blogs.asterisk.org/2016/08/24/asterisk-14-ari-create-bridge-dial/ in node.js asterisk-ari ? thanks Marek

Hi, When have a incoming call from E1 to a extension FXS, and this extension is busy, the incoming call recive ring tone, and it is wrong. What can I do? Thanks in advance Pedro Here is the trace: asterisk-1*CLI> < Protocol Discriminator: Q.931 (8) len=41 < Call Ref: len= 2 (reference 66/0x42) (Originator) < Message type: SETUP (5) < Sending Complete (len= 4) < Bearer

Hello, I am facing hangup delay problem using FXO (X100P) card with the following scenario: PSTN Phone--------->BTTB PSTN Gateway------->Asterisk BOX-FXO-------->SIP Endpoint When anyone make call to my Asterisk-BOX FXO, they gets IVR to press their desired SIP extension number. If calling party disconnect the his/her call before pick up the call by the called party, then called

Rob at draughon.org writes > I recently obtained a Western Electric multi-line phone and am >seeking help with getting this beast working with *. > > The interesting stuff in my * implementation consists of a T100P >card, a TDM400P card, and an Adtran TA750 channel bank with three quad-port >FXS modules and a quad-port FXO. The TA750 is wired to a 24-port Cat 5 patch >panel

> On Jan 2, 2024, at 23:17, thelma at sys-concept.com wrote: > > On 1/2/24 15:13, asterisk at phreaknet.org wrote: >>> On 1/2/2024 4:03 PM, thelma at sys-concept.com wrote: >>> I'm using asterisk-16.30.1 >>> >>> When I try to call another asterisk server over IAX I get a busy signal, >>> >>> chan_iax2.c:4739 __auto_congest:

I upgraded from 1.0.9 to 1.2.1 My IVR which worked perfectly on 1.0.9, now hangup with no reason (at least I could not find a cause) When this hangup happen, I can read: == Auto fallthrough, channel 'IAX/user-20' status is 'BUSY' This happening also with ZAP channels I'm really disappointed with 1.2.1, what is benefit from upgrade if I must spend couple days to get my system

This is a global message to all to announce our callcenter / dialer / predictive dialer / vicidial program is now open. Codecs: G711, GSM, G729, G723 Protocols: SIP Duration Rate : 30/6 (6/6 with monthly minutes over 100,000) Channels : 100 to start with , more on demand. We are predictive dialer friendly , your account will not be shut off. Contact us to do a test run. Mike

Hello all, I am trying to use native h323 built from asterisk 1.2.7. I configured the h323 to receive incoming calls...the problem is i can receive the call to my asterisk and it rings another extension but no audio. I don't see any good documentation about gatekeepers, fast start, etc with h323. I would like to get some help from you guys to fix this issue. If any of you have configured