similar to: Problem with simple incoming calls

This was submitted to the Dev list last week, but there was no response, and perhaps it wasn't the right group. I am developing an application in which I need asterisk to pass on an incoming call to a separate IVR server. The problem is that asterisk appears to hang up while the IVR is playing back a sequence of recorded voice and systhesized voice prompts. My setup is: Analog line

It seems consistant after dialing dozens of times that the call that doesn't go through is the one the gets the log message "No echocancellation requested" (chan_zap.c) and the "Scheduleing timer" (channel.c) in the middle of receiving the DTMF tones. I'm now using the T400P card last week very simular problems the the T100P (although I think I was actually loosing

hi all, i have an asterisk install with a digium 4 port fxo card and cisco 7960 sip phones -- running on a compaq Pentium III (Coppermine) at 800Mhz 256KB cache and 1GB of ram. when a call comes in on zap/1-1 for example, the delay between when zap sees the line going to ring state, and when the desktop telephone rings can be as long as 7000 milliseconds (or about 3 or 4 rings on an ear piece).

So I reached the point where my PRI is accepting incoming calls, but I cannot dialout. I must be doing something stupid, but I can't figure it out. The Asterisk box is sitting between the Mitel and the phone company, and has PRI lines to each. Asterisk was built from CVS r1-0 Log for a call from mitel heading outbound: ------------------------- -- Accepting call from '' to

I must be doing something stupid, but I can't figure it out. I have three PRI lines connected to Asterisk, one from the phone company, and two more connected to PBXs. Asterisk uses the incoming DID information to decide which PBX to route the call to. Should be simple. Asterisk is clearly getting the caller id info from the phone company: -- Accepting call from '512345xxxx'

Well, my faxes passes through asterisk successfully, however I still have some problems about fax reception by rxfax. The softfax answers, and negotiates transmission, however then as some stage of communiation something is wrong. But I have nothing more but this log: Jun 2 00:10:21 DEBUG[16900]: chan_zap.c:4242 zt_read: DTMF digit: * on Zap/10-1 Jun 2 00:10:22 DEBUG[16900]: chan_zap.c:4242

I've got a new setup (different building) where Asterisk is sitting between the PBX and phone company on a E&M T1 line. Mitel PBX <-> Asterisk <-> Phone company Inbound works. Asterisk gets the in-band digits from the phone company and hands the call off to the Mitel just fine. Outbound is weird. Asterisk seems to expect that the mitel will send routing information

Hello I have an interesting situaltion and not sure if I am doing something wrong or it is a BUG. I Installed Rhino Channel on T1 line and connected Analog Phone on Rhino's Zap Channels. If i pickup analog phone and hangup without dialing any number , I am getting extra ring after hangup and if i dial any digit than there is no ring on Analog phone after hangup. Log's looks like this

Hi, I'm having problems using a TDM400P Card. I put my SIM card in a Nokia Premicell and connected it to a TDM400P card but when I make calls to the number, it hangs up automatically. The card also can't call out. Any ideas? I've searched the archives without much success. I appreciate all your help. Details: I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an

Trying to compile asterisk (again) from scratch. I seem to be still experiencing the effects fro Jan 25 where I get no sip to sip audio. I have tried upgrading to 1.2.3 which has made no change in the problem. I am starting over and now trying to compile/install /trunk zaptel libpri asterisk following the instructions to grab the source trees: # svn checkout

Hi all, I've been running Asterisk with a TDM400P for about 6months, no problems. 2 in/outgoing analog lines, one analog phone. Recently I was messing with the XTEN client, got to finagling with things, and not knowing what was wrong I upgraded from 1.0.7 to 1.0.9 (both asterisk + zaptel). I was testing various things, and found everything worked except outgoing calls. So I checked

Any ideas on this warning? If I call this number, sometimes I get this error and sometimes the call goes thru fine. Why would it work sometimes? -- Executing Goto("SIP/3044-8d49", "cytel-outgoing|915124512424|1") in new stack -- Goto (cytel-outgoing,915124512424,1) -- Executing SetCIDNum("SIP/3044-8d49", "2814494000") in new stack --

Hi, When startin * it tells me: ================================ [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf: Updated conferencing on 1, with 0 conference users -- Registered channel 1, PRI Signalling signalling Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf:

Dear All, I just setup the Asterisk with E100P which it's no problem in Dial In but I have problem when outdial. The connection method is like this : E1 PRI <-SIGNAL-1-> MaxLink (PBX) <-SIGNAL-2-> E100P <-> Asterisk <--> SIP \-----> Analog PHone Now when I tried to dial out by SIP X-Lite on Windows, it shows me Connect, Trying,

Hello, I have problem to make SIP calls, i have asterisk + PC InterP4 + Digium TDM400P here is the content of the sip.conf: [SIP_PROVIDER] type=peer fromuser=testcomclient username=testcomclient secret=testr host=IP_SIP_PROVIDER ;dtmfmode=rfc2833 context=interne canreinvite=no ;allerid=Beer disallow=all allow=ulaw allow=gsm allow=g723.1 ; Asterisk only

I am having some problems with g729 with SIP and ZAP channels. 1) I have two g729 licences. Very frequetnly (I don?t know what triggers the error) I get the following warnings and error when I try to place a call via SIP to my X100P. The only way to get out of this is through a restart of *. When the error ocurrs there are no other calls in place. Any ideas? Error Opening channel:2 not

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I recently updated (fresh checkout) to the newest zaptel and Asterisk. The one I was using before was a couple of months old. After updating, my zap channels don't work. They won't pick up incoming calls or dial out. When I try to dial out I get: -- Executing Dial("SIP/3064-564c", "Zap/g1/ww954.......") in new stack NOTICE[245776]: File app_dial.c, Line 698

Hi Everybody, I am trying to use SIP (Sipura 2000) to connect to Asterisk which then dials out a local number using the Digium E100P. We have purchased the G729 codec licenses from Digium and loaded them into Asterisk successfully. However, the call drops immediately after being answered with the debug error message saying something like: "channel.c:2646 ast_channel_bridge: Didn't get a

Guys, this error has been driving me nuts and I see no indication anywhere as to what it may mean. Anybody has any clues on this? -- User ended message by pressing # -- Playing 'auth-thankyou' (language 'en') -- Playing 'vm-review' (language 'en') -- Saving message as is -- Playing 'vm-msgsaved' (language 'en') Mar 4 21:02:06