similar to: Problems and questions with setting up a Feature Group D trunk to a Nortel DMS-10 switch

Hello list, I''ve been using linux and open source software for over 5 years now and I want to give something back to the community. I''m working on a PHP-based project (SPITS). The aim of this project is to easly create a shaping script, using a web interface, without needing to know tc and iptables command line options. As the project is now in beta stage, soon a CSS

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the

Hello All, I'm trying to connect Asterisk to an Executone phone system with an analog DID card and I'm hoping someone can help me figure out what I'm doing wrong. The Executone DID card provides battery to the telco, when the telco wishes to dial a DID it goes off-hook, waits for a wink from the Executone and then dials the last three digits on the number with pulse (as opposed

Hi All, We successfully installed MFC/R2, chan_unicall.so with asterisk ver 1.2.6. asterisk is loading properly and we can see US show channels working fine. We are using digium Te120P card. Now we are trying to setup E1 link with Nortel DMS 100, which is resides at one of telco provider in Sri Lanka. But we don't know what is the exact protocol varient to use. Is anyone help us out on this

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

We have 2 T1's coming from our phone switch to a digium TE220B. We have managed to get CPN and the extension outpulsed from the switch, but call setups are really slow. Our T1's are set up as E&M Wink, and they send us the last 5 digits dialed followed by the 10 digit calling party number (we couldn't get the switch to be happy with *CPN*+5* to use featd). We are using asterisk

Help. Why is it that I can call out from my GSBudgetone SIP phone but the audio is "one-way'? Why is it that when I call my asterisk phone number, I get a fast busy?

Ein eingebundener Text mit undefiniertem Zeichensatz wurde abgetrennt. Name: nicht verf?gbar URL: <https://stat.ethz.ch/pipermail/r-help/attachments/20111023/ae046d6a/attachment.pl>

We have an old Telrad 128KSU PBX to which I am trying to connect asterisk in the following manner: Current Setup: Telco-> T1->PBX Desired Setup: Telco-> T1-> Asterisk-> T1-> PBX. I am first trying to setup the Asterisk -> T1->PBX part without disturbing existing setup so I can get asterisk to forward calls to PBX and once that is done, I would try to move the telco

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Group When I dial a phone number that should go out to the telco my local phone rings. Does anyone have any hits ? Thanks Asterisk Ready. *CLI> -- Called g1/6144196143 Urgent handler Urgent handler -- Starting simple switch on 'Zap/2-1' Urgent handler Urgent handler -- Called 6149236651 Urgent handler -- SIP/6149236651-1d93 is ringing Urgent handler -- Zap/1-1

Does anyone know the default E&M Wink timings for Nortel DID ports? The default settings on Asterisk are: ; prewink: Pre-wink time (default 50ms) ; preflash: Pre-flash time (default 50ms) ; wink: Wink time (default 150ms) ; flash: Flash time (default 750ms) ; start: Start time (default 1500ms) ; rxwink: Receiver wink time (default 300ms) ;

... Well, this works in this simple case, but is too clumsy for a general formulation of this problem: given a "dictionary" consisting of two character vectors of unique "names" (or two columns in a data frame), x and y, how does one convert a factor z with levels in x into the corresponding equivalent with levels in y? There are likely a zillion ways to do this with various

Hi All, Sorry for the double post, but I'm in a real bind. I have several * servers connected to T1 PRI's from various service providers in multiple locations the US. All the * servers use the same hardware with the same OS and * version CVS-v1-0-11/09/04-12:27:27. When connected to 5ESS Switches, using the NI2 (national) PRI protocol, the CID name and number come across fine and

Hi Guys, I have several * servers connected to T1 PRI's from various service providers in multiple locations the US. All the * servers use the same hardware with the same OS and * version. When connected to 5ESS Switches, using the NI2 (national) PRI protocol, the CID name and number come across fine and populate into the * CDR fine. I connected to a DMS-500, NI2 (national) protocol and

Hello everyone! I have a little problem: HRH = trusted domain (Samba 3) Hendricks = trusting domain (NT4 sp6a) Trusts are setup between the NT4 and Samba3 + OpenLDAP domain and appear to be working properly. When logged into the HRH domain on a W2k workstation I can view,read, and write on available shares for HRH groups and users on our Windows file servers. Whenever I try to see available

> > Hello All, > > I have been struggling with this for a long, long time. I came here > looking for answers. So, I have a VM running Debian Lenny. I install > the apt package samba, which installs 3.2.5. I work in a large > university with an extensive Active Directory environment, both forest > and domain running in Win2k native mode. There is a NetApp filer >

I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |

Hi list, For a client I am setting up a system which will use T1 PRI from Primus, who offer only NI-1 and NI-2 protocols for D-Channels. Previousely I have only used switchtypes euroISDN and National. Although the documentation says Asterisk does support NI-1 ans NI-2, but wanted to get your opinion if you have used these protocols on an Asterisk box and if there were any things to consider. If