similar to: Can Asterisk work in a proxy setting- a challenge

Hi, is it possible to use Asteriks for translating SIP to H323 and vice versa? I am looking to implement the following Setup SIP UAC <-> SIP-Server <-> SIP/H323 Proxy <-> H323 Server <-> H323 UAC Basicly i want SIP fones to talk to H323 fones and and SIP Fones to access PSTN Gateway(s) in a H323 network. Anyone got something similiar running? Any ideas? best regards,

I need to receive a FAX call from a SIP device into my Asterisk box, then send that FAX call to an H323 gateway and bridge the call, so Asterisk will be acting as a Converter. SIP device is a Grandstream HT496 so i can configure FAX Pass-through, but the H323 gateway only supports T.38 BTW, i am able to make voice calls from SIP device to H323 gateway, the problem is with FAX How can i do this?

Hi All, I am new to Asterisk and VOIP. I managed to get it working with sip(X- Pro) and skinny(Cisco 7940,7960). I have a call manager to which all the phones are connected. I would like some assistance integrating CCM with Asterisk. I was trying to understand the H323.conf file, but got nothing in it. Any steps, any config, any help would be highly appreciated. Thanks & Regards, Gurdeep

hello every body, i have big problem to configure h323 trunk between cisco router and asterisk 11.13.1 which uses ooh323 module. any body knows if ooh323 module can work with cisco routers or not???? (in gateway mode, it is ok and register in cisco gatekeeper but i can not configure trunk h323) any comments or hints are really appreciated. SAM -------------- next part -------------- An HTML

Dear friends, I have compiled and installed h.323 in my asterisk. And I have a service from a H.323 VoIP provider who give me user, password and gatekeeper IP address. All configured. But when I start my asterisk i receive the following error and h.323 calls can not be making and/or receiving. [chan_h323.so]=> (The NuFone Network's Open H.323 Channel Driver) == Parsing

Hello, Could somebody tell me is it possible to use asterisk without RTP proxying in SIP<->H323 calls? I mean exactly what canreinvite=yes option do in SIP<->SIP calls. I don't need a transcoding, only a signaling conversion, and this is possible with some softswitches, so i wondering what about asterisk. Same question about H323<->H323 calls I'm using NuFone

Hello All, Finally I realised that the Asterisk demo setup didn't include support for h323. (Maybe it should have been obvious) so I went to work out how to get the h323 channel running. I had openh323 and pwlib installed as I'd been playing with vocal so it didn't take long to do cd asterisk/channels/h323; make; make install; make samples, copy the pwlib and h323 libraries to

hello Dmitry thank you for your reply. Ok, you are right. i want to configure trunk h323 between asterisk 11.13.1 and 2800 cisco router. this is my scenario: PBX(100)--->cisco--->asterisk11.13.1---->PBX(200) when i call from 100 to 200, everything is ok but when i call from 200 to 100, phone rings but after i answer it, i have no voice and call terminates after 5 seconds. this is

Hi all, What is the correct way to give one non-root user the ability to use DTrace with providers running in a process by another user? Through the Web Stack project and some work by Ludovic Champenois and Nasser Nouri, we have done a bit of work to bring together parts of chime, the Web Stack Apache, Ruby and PHP providers, and stuff reused from the DTrace toolkit. It''s in

Hey guys, When a call comes in via the PSTN to our Call Manager 3.2 and is forwarded (via unity and H323), the caller id is set to our Unity Voicemail instead of the caller id from the PSTN. We're using the oh323 channel in this case. Has anyone experienced this issue before? Any solutions? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all, I''ve been Googling this one for a while now, and haven''t found a satisfactory answer. It has been posted here before by someone else, but it seems to have got forgotten, so here goes - perhaps someone can think up a way around the problem? In ApplicationController, I have the following method: class ApplicationController < ActionController::Base <snip>

On 04/13/2011 02:58 AM, Shridhar, Vasant wrote: > I am doing this right now with no problem. I am not using speex for this at the moment though. Group delay is the biggest problem. I implemented a version where the input and output sample rates are known up front. The routine than interpolates between the jitter. This should solve the problem. The crystals used to clock the input and

Aloha, I have a Cisco Gateway the is functioning as my SIP Gateway to the PSTN. I have an Asterisk box, RC2 with a for port FXS card providing dialtone for a Norstar Key System. I have it working so when you press a line key on the Norstar you get dial tone from the Asterisk box. The user has to dial '9' then they can dial there number which is sent to the Cisco GW via SIP and the call

Our outsourced IT department has decided to use white listing on the firewalls for outbound ftp. I was given a list of sites our lab had accessed via ftp and eventually tracked them down to Linux machines running yum. They are all CentOS 5 or 6 with a smattering of 7. It is impractical to list all the possibilities since they change on a regular basis. Also any 3rd party repos we need are

hi guys, i am getting today my dev kit with fxo and fxs boards. i intend to do the following : 1) be able to route an incoming call from the pstn fxo port to an ip (answering with netmeeting or anyother sip softphone) 2) be able to call from netmeeting to my pstn fxo port to place calls. questions : how can i do this ? what are the commands for this simple setup ? how can i place calls

hi .. i've just installed and licensed an instance of the G729 codec. I am trying to connect through asterisk to Go2Call server .. According to their info it involves dialling extension 729 on voip01.go2call.com, to get the IVR. my extensions.conf shows : exten => s,2,Dial(OH323/h323:729@216.52.153.206) which I think is correct, I have G729 enabled in the OH323.conf file and it seems to

Hello All, I am trying to setup a SIP to H323 system using SER, Asterisk And GnuGK. Following is the configuration: CISCO ATA (NAT) -> SER -> ASTERISK -> GNUGK My Cisco ATA is registered with SER and When I dial a number, SER forwards the call to Asterisk, and Asterisk forwards the call to the GateKeper. This is ok, call reaches the gatekeeper, however the gatekeeper drops the call

I'm trying to use a Howlink CL-100 ip phone with * It's h323 phone with very limited protocol support. But it's enough that I can use it to dial netmeeting client and artisoft pbx just fine. When I try to dial my * with it using either chan_h323 or oh323, it seems to fail on negotiating H245. Maybe this phone doesn't support it? I've used all different versions of

Hi All, I have set up a box that will be used as follows: SIP Phone ----> Asterisk ----> Cisco H323 VoIP Server 192.168.1.5 192.168.1.50 192.168.1.80 Asterisk is running the latest CVS and oh323 driver. The SIP phone is a Grandstream Budgetone 100. I have everything setup and running with G.711 ALAW and ULAW and i'm able to make calls through

Hello... I'm having problems with H323/G729 setup. Below is the output of h.323 debug when making a call. I use a SIP phone connected to an * box in the same LAN. The * connects to a h323/g729 PSTN terminator through internet. Calls rings and are answered in the other side, but I get no sound at all nor the other side does (complete silence in both sides). I thought this would just happen