similar to: Unable to register channel

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Hello! I discovered, that I'm unable to load ther kernel module under 2.4.28. Before that I had 2.4.26 and tryed to upgrade the kernel to 2.4.28. After restart (reboot - soft restart) I can't load the module. When I go back to 2.4.26 and try to load the module, I'm getting the same problem. Only turning off/on helps. What can I do? It's very annoying because the box is in hosting

Hmm, I don't have /etc/modprobe.conf, and wctdm is giving me problems. Which device is it talking about? [root@asterix /]# modprobe wctdm /lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hi, Is there any difference between decoding of CBR or VBR streams in realtime in terms of CPU usage/cost? Are sample rates other than 44100Hz supported by Vorbis officially ? If it is supported, is it efficient to use them or is Vorbis specifically (or at the moment) optimized for 44100Hz ? Thanks in advance. --- Mete BALCI Senior Game Programmer Momentum DMT Istanbul, TURKEY

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

I have a E110P which I can't seem to make function and i think it has something to do with interrupts, but I've never had to deal with them before and was wondering if someone could offer some guidance. a modprope zaptel loads fine. when i then do modprobe wcte11xp i get the following: /lib/modules/2.4.21-27.0.1.EL/misc/wcte11xp.o: init_module: No such device Hint: insmod errors can be

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Hi I'm trying to get a Digium TE110P card working but as soon as I load the module with modprobe wcte11xp the sound stops working for incoming calls (SIP and IAX). I haven't even started to configure the card. Running ztcfg and restarting asterisk doesn't help. After unloading with rmmod wcte11xp the sound comes back for new calls I'm using asterisk 1.2.4, libpri 1.2.2 and

Hi: I'm using a te110p E1 card in Spain. There is way to change the dchan channel number? Here in Spain there is a voice company that works with dchannel in channel number 31. I must to set channels from 1 to 30 and dchan to 31 but when asterisk loads the chan_zap.c it says that channel 16 is reserve for dchan. Can you help me? Cheers. -- Jos? Luis Garc?a Ext. Pineda 2002001 Ext.

This is a system for our lab. I have no problem getting rid of X100P clones. But I am just curious why can they work. Even the drivers are not loading correctly. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kerry Garrison Sent: Tuesday, May 02, 2006 10:51 AM To: 'Asterisk Users Mailing List -

Can anyone describe the asterisk implementation of this any better than the sample config files do? from zapata.conf ; Trunk groups are used for NFAS or GR-303 connections. ; ; Group: Defines a trunk group. ; group => <trunkgroup>,<dchannel>[,<backup1>...] ; ; trunkgroup is the numerical trunk group to create ; dchannel is the zap channel which will

Hi, I have problem using Asterisk.I have isdn-pri and openvox d110p card in my computer.They are connected with RJ-45 (1,2,4,5 pins to the card and all pins to the isdn done by telco workers). I got green led on isdn which is sign that isdn is working and that is connected to openvox, right ? I compiled newest versions of libpri zaptel and asterisk and had no problems during that. When I started

I am having problems loading the zaphfc from bristuff and wcte11xp drivers at the same time. If I load zaphfc then all works fine. If I then load wcte11xp, the card using the zaphfc doesn't pick up calls anymore. I am using bristuff 0.2.0-RC5. Anyone else seen this problem, know of a fix, or can tell me what I am doing wrong? Thanks My zaptel.conf: # hfc-s pci a span definition # most of

I'm not receving anything from the list, is this a Gmail problem? or just my account?

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

Today we have been having some problems with the dchannel of out T1's. I was wondering if there is a way for asterisk to send out an email or page whenan error occurs. Not I know errors happen quite offen for many reasons, but I would like an email sent when there is a TI problem, or specefic other problems. I am using the safe_asterisk to run asterisk and it sends an email when asterisk

Hi guys, Currently I just purchased the TE205P for the installation of my ISDN30 setup. I compiled, setup the card correctly I think. When I do the ztcfg -vvv it shows all 31 channels clear, with 30 bchannels using for voice ranging from 1-15, 17-31, and 16 is the dchannel. However, when I do a cat /proc/zaptel/1 I see only 24 channels configured, and then, when I do a cat /proc/zaptel/2 I see