similar to: Need help configuring TE100P and 3 X100P clone with MD3200 chipset

This is a system for our lab. I have no problem getting rid of X100P clones. But I am just curious why can they work. Even the drivers are not loading correctly. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kerry Garrison Sent: Tuesday, May 02, 2006 10:51 AM To: 'Asterisk Users Mailing List -

Hmm, I don't have /etc/modprobe.conf, and wctdm is giving me problems. Which device is it talking about? [root@asterix /]# modprobe wctdm /lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Hello, i've googled and can't find a definite answer, so here goes: I have purchased the Digium TE100P, and am setting up the connection, however the telco i'm supposed to work with does not support PRI/ISDN E1 connections. They only support E1/R2 lines. Is there a way i can make the TE100P work with this? I've not seen any zaptel.conf that supports this. Any workarounds?

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Hi, I have a Gateway running in "TE" (terminal equipment mode as "slave" that I need to connect to my asterisk server using a TE100P card. Can anybody give a quick run up of how to run the TE100P's in Network Termination mode to have this working sucessfully? Cheers! Regards, Sahil Gupta VoiceValley

Hi, I have a problem I will describe. I have PAP2 connected to the internet to an asterisk box with 2 TDM cards, one TE100P E1 with PRI and one TDM400P with 2 FXS an one FXO. When I call to the TDM400 cards from the PAP2 eveything is OK, sound quality is perfect. When I call to terminate the call in PSTN through E100P I hear clicks which aparently are RTP packet looses. This clicks are only heard

It seems the information out there on this topic was confusing enough to cause me to waste a lot of time, and that this topic is rehashed periodically. So now it's my turn.... I had a modem with an Intel 537EP chip on it and thought it might work with the zaptel drivers. Initially, it seemed the only issue would be the PCI device & vendor codes. Then, I ran into the problem that

Hello, my first post to the list. I have started to install and play with Asterisk. I was following some basic instructions to 'jump-start' my system. I have a TDM400P with one port and a X100P. I am running the latest CVS versions (from today). Following the steps I found for basic jump-start I did the following: Modprobe zaptel Modprobe wcfxo Modprobe wcfxs Edited

Hi All, I have the problem setting up TDM22B card. Steps what I have followed are: [1] compiled zaptel-1.0.9.2 & installed the same. [2] modprobe wcfxo /lib/modules/2.4.20-8/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hi, using Sangoma drivers: - doing 'lsmod', I see: zaptel ... wanpipe,wctdm24xxp,wctdm,wcfxo,wcte11xp,wct1xxp,wct4xxp,tor2 I'd like to avoid loading all these modules. What have I to do? - do I need to have 'zaptel' startup script under /etc/init.d ? Thanks -- Domenico Viggiani

Hi people, I'm having some problem when I reboot my machine. Every time that I reboot the system, the zaptel changes the order loading of the cards. I have 3 cards (wcte11xp, wctdm and wcfxo). So, my configs in the zaptel.conf will be always wrong, because I change the config for a order loading, and when I reboot its change! I tryed to see the config in /etc/udev/ but I think its right,

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

Hi List, I am having some trouble with installing the latest version of ztdummy on a CentOS Kernel 2.6 system. I have installed a few Asterisk systems on Slackware Kernel 2.4.x without any issues, unfortunately there is no choice about this distro, or kernel as it has been preinstalled by someone else. And so I am in the dark with an unfamiliar distro and kernel. I am fairly sure the

I originally built my Asterisk server without installing the Zaptel package as it was going to be a purely SIP based system. However when I went to setup conferencing using meetme I found out that app_meetme is dependant on the ztdummy for timing. I have now installed the zaptel package and I believe the ztdummy module is loading ok [root@astro asterisk-1.4.0-beta2]# lsmod Module

Hi all, What hell hapen here? asterisk:/etc/asterisk# /etc/init.d/dahdi startLoading DAHDI hardware modules:FATAL: Error inserting dahdi (/lib/modules/2.6.26-2-686/dahdi/dahdi.ko): Device or resource busy wct4xxp: done wcte12xp: done wct1xxp: done wcte11xp: done wctdm24xxp: done wcfxo: done wctdm: done wcb4xxp: error wctc4xxp: done xpp_usb: doneError: missing /dev/dahdi! When

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel