similar to: PRIs from two different telco

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Evening, My latest asterisk box is having a difficult problem. It is configured with one TE210P and TDM400P with four FXO modules. I'm running FC6. The TE210P only has a single PRI. When the system boots, it is completely random what order the zaptel modules will get loaded in. Sometimes zttool shows the FXO as the last span, sometimes as the first. When it does load as the first, which

I am experimenting with an asterisk setup in my office. The last bit I have to test is working with analog lines. I have TE411p digium card, with an ISDN line plugged into the first, a channel bank plugged into the second port, and the last two ports empty. I have the following setup in my zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,d4,ami fxsks=25 And in zapata.conf, I

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

Hello, I'm having issues connecting throu PRI with the following error "Requested transfer capability: 0x00 - SPEECH" Below are the logs: == Using SIP RTP CoS mark 5 -- Executing [97052660 at voipphones:1] Set("SIP/4856-00000003", "CALLERID(num)=xxxxxxxxx") in new stack -- Executing [97052660 at voipphones:2] Dial("SIP/4856-00000003",

I'm trying to get a Qwest PRI configured and working with my lab Asterisk server. They said that the switchtype is 5ess and the signaling is pri_cpe. My entries into zaptel.conf are: span=1,0,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us channels=1-23 And my entries in zapata.conf are: language=en context=telco-incoming switchtype=5ess signalling=pri_cpe

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

Hi, I running into the following problem on my Asterisk setup: --snip-- [Sep 3 01:40:59] NOTICE[9170] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 3 [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: Asked to delete sched id -1??? [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler [Sep

Hi, I'm getting the following error from an asterisk 1.6.0.9 installation: [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: Asked to delete sched id -1??? [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: No more room in scheduler This repeats a few times, then asterisk crashes. I can't seem to locate any info on this error at all. I'm using

I just implemented a system using a TE411P hardware echo cancellation card. Per Digium, I setup zaptel.conf, and zapata.conf the same way as I always have. To my surprise calls out to the PSTN had a terrible echo. 1 - 2 second delay, and quite clear. The echo was so bad that I had to remove the hardware echo cancellation module from the card. We are only using the 1st span of this card right

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

Hello. New to the list. We're in the process of deploying Asterisk. Actually, we're going live tomorrow, and I just found out that my Zaptel cards have been mis-configured. I'll preface this by saying that I have looked in the wiki, read through the samples, and attempted to call Digium (they're closed.) So I'm praying that someone on the list can help me out! I have two