similar to: Help on chan_misdn and MSN's

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

Hi list, I have a server running a simple hfs isdn card running with chan_misdn. the problem is, I can't get asterisk to pick up the phone, outgoing calls work fine. when running asterisk with -vvvvvvvvvvvc I get the following "log" when I try to dial the isdn server. P[ 1] * Starting Ast ctx:kpn-in dad:0594643637 oad:0878722291 with 's' extension P[ 1] MGMT: SSTATUS:

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Hello everyone. I've got a HFC ISDN card that I'm using with chan_misdn and it basically behaves like crap. Echo is waaay worst then echo I get TDM400 card, sound is "choppy" (there other side is allays complaining about sound interruptions) and to top it all it detects fake DTMF's all the time. Is this a chan_misdn problem or is it a card problem? I really need to get

Hi, I have switched a while back from chan_capi to chan_misdn. When the number is dialed and the phone is then picked up everything works just fine. Some users however FIRST pick up the phone and then start to dial... I did not get this to work with misdn. When two digits have been dialed, asterisk sees the extension as complete and does not wait for further digits. I am using an midsn NT

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

Hello I have just set up Asterisk Asterisk 1.4.21.2 on a CentOS 5.2 machine. I am using the OpenVox B200P ISDN card. My problem is that even though chan_misdn module seems to be loaded correctly with Asterisk (I can see it using 'module show' command) the misdn commands are not available to me in the CLI so I cannot tell if my box is correctly interfacing with the ISDN card Any ideas

Hi all! I'm getting an error when I try to start asterisk with chan_misdn. I patched my kernel (2.6.12.4), and compiled the whole stuff (kernel, mISDNuser, asterisk, chan_misdn). I got mISDN from http://isdn.jolly.de/download/v3.0/ I'm using a CVS Snapshot of asterisk, which was checked out about 5 hours ago. This is the error: [chan_misdn.so]Aug 15 14:13:29 WARNING[4929]:

Could someone please comment on the current state of chan_capi, chan_misdn and chan_modem channel drivers in terms of functionality and stability. Specifically, which channel driver would be best for a passive PCI HFC or W6692 ISDN card. The chan_misdn wiki claims that chan_capi distinguishes between junghanns and non-junghans cards, and that chan_misdn is better suited for general misdn

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

Hi List, I?m having problems compiling chan_misdn: asterisk:/usr/src/chan_misdn-beta-0.0.3-rc4 # make install cc -ggdb -Wall -D_GNU_SOURCE -Wno-missing-prototypes -Wno-missing-declarations -fPIC -I/usr/src/asterisk/include -DAST_CONFIG_DIR=\"/etc/asterisk/\" -I/usr/src/mISDNuser/include -I/usr/src/linux-2.6/include -I/usr/src/mISDNuser/i4lnet/ -Wall -c -o chan_misdn.o chan_misdn.c

Hi all, I've been having problems with my A20002D lately - callers from the PSTN don't hear me when I answer, but I hear them. Disabling echo cancellation in zapata.conf brings the audio (and echo) back. This used to work fine, until two days ago. The only weird thing in the logs is this: May 12 07:42:53 steerpike wan_ecd: wp1ec: The H100 slave has lost its framing on the bus! May

I'm running a setup with chan_misdn on a austrian PTP-line. When somebody dials in without an extension, he gets a busy signal. I don't see the call at all in asterisk. I *have* set immediate=yes in misdn.conf. And I *do* have an s-extension in my dialplan for the context used by misdn. Calls that provide an extension work fine. Attached is my misdn.conf and a verbose 3, misdn set debug

What are the advantages in using mISDN over other solutions? If I knew why it was a good idea (like does it have better sound quality than alternatives?) then I would put the time in to test it, and also improve the Wiki. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Thomas H?ger Sent: Friday, January 21,

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

Has anyone got chan_misdn working with passive BRI cards yet? I've tried both hfc (hfcpci.ko) and w6692 (w6692pci.ko) cards, but when I start asterisk I get the following when chan_misdn is loaded: [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found == Registered channel type 'mISDN' (This driver enables the

Hi, Has anyone had experience installing it? yum install asterisk-chan_misdn I'ts the latest Trixbox Distro version and same issues exists if add in the Trixbox repo. FAILS as per below: I have a ISDN single port PCI BRI card installed and detected. __________________ Loaded plugins: fastestmirror, kmod Loading mirror speeds from cached hostfile * addons: www.ftp.saix.net * base:

Hello I want to setup an Asterisk in several offices with 4 BRI ISDN. I am looking for recommendations on hardware. Criteria would be ease of setup, reliability and cost. The Eicon 4 BRI cards seem fairly pricey. Shame Digium don't do a ISDN BRI card. Angus -------------- next part -------------- An HTML attachment was scrubbed... URL: