similar to: Quintum D3000

Well the subject line probably says it all. I have a Quintum D3000 which I'm supposed to be getting connected up to our Asterisk system. No matter what I try, neither username or authuser config works. I've also tried md5auth and it still refuses to register. Any one have a config they could share with me? Any help would be much appreciated. Neil

Hi all, I am planning to use VoIP gateways to connect remote offices to Asterisk. Not having much experience with these and Asterisk I would appreciate any info/experience that you might share with me as to their interoperability with Asterisk. I am interested with in rather bigger gateways (order of E1's) from: AudioCodes - Mediant Mediatrix - 1531 Quintum tenor Multupath D3000 Has anyone

Hi, I'm having problems to register Quintum Tenor DX 3020 on a Asterisk box with SIP. Asterisk always returns "Username/Password mismatch". I've tried all configurations that was on the Quintum's manual, but no success. I've tested the same username and password with a Linksys (PAP2-NA) with the same asterisk box, and it worked fine. Where is the problem ?

Hello *'s, I have question regarding Quintum Tenor AXT800 VOIP gateway can anyone integrate it with asterisk if anyone what is the scenerio i have scenerio which is quite simple but i am confused about it whether it is possible or not : I integrate it with asterisk for interanet no PSTN at all just only IPphones and analog phones connected on FXS port.Is it's neccassary to cannect with

Hi, just wondering if there is anyone that can help me configure my quintum box to operate with asterisk. i have tried and made numerous attemtps configuring the tenor to work with asterisk@home but have been unlucky. anyone out there has a cheat sheet to configure this device. thanks.. for some reason i cannot get it to work. your help is appreciated.

Let's try this again. I have a Quintum AX Tenor gateway sending calls to Asterisk from BT analogue lines connected to FXO. The agents hear an echo on their side but incoming callers hear the conversation fine. I can't seem to find the problem. Anyone seen this issue before? <p style="margin: 0; padding: 0; border-collapse: collapse; font-family: Tahoma, Arial, Sans-Serif;

Hello all, I post this issue thinking too that could help other people on an asterisk deployment over distributed offices considering both quality, prices, devices and so. Well, i am working on a deployment of a telephony system based in asterisk. My company have a central office with seven remote offices connected all through a VPN. To reduce and evaluate costs i consider solutions like:

Hello, I try configuring Quintum DX gateway as link to PSTN for *. Now, I can dial number which is connect to Quintum, and call is diverted to *. I don't know what I should set, if I want call from SIP_phone registred in Asterisk to PSTN via Quitnum. I set in sip.conf account for Quintum [sip_proxy-out] type=peer outboundproxy=QUINTUM_IP , and changed extensions.conf. When

Hello *'s, I have question regarding Quintum Tenor AXT800 VOIP gateway can anyone integrate it with asterisk if anyone what is the scenerio? i have a scenerio which is quite simple but i am confused about it whether it is possible or not : I integrate it with asterisk for intranet no PSTN at all just only IPphones connected through ehternet port and analog phones connected on FXS port.Is

Hi all, Can someone share with me his experience in making asterisk-oh323 talk to quintum gateway without gatekeeper. My set up is QUINTUM GATEWAY ------IP----M ASTERISK (OH323) Both are gateways.. but I don't know what authentication I will set up in oh323.conf and how to set it up I will be glad if anyone can help Goksie

Hi all, Im trying to build an small home system. I have 2 pots lines, and i need to make 8 extensions and be able to use my old analog phones. What would you recommend to use as the 8 FXS switch? I saw some equipment from quintum, they have a Tenor AS that offer 4 FXS ports. But i don't know if it is the best solution. Does anyone have a better solution to build this system? If an analog

Hello, I got Quintum A800 with the P5-2-1 firmware. I configure my asterisk trunk as followed: [SIP_BD1] type=peer qualify=yes host=192.168.0.254 disallow=all context=from-pstn allow=h723 and inside the quantum I change the config sip useragent to 5060. Up to this part if I run sip show peers, I got: asterisk1*CLI> sip show peers Name/username????????????? Host??????????? Dyn Nat ACL

Good day all Is it possable to set asterisk up as a cdr server for other voip units We got a quintum dx here and its got a option to log to a cdr server on port 9002 Thanks Altus

Hi All I'm trying with no luck to connected the Quintum D series Gateway with the new SIP release to asterisk. Have anyone done this? If yes then how should I configure the sip.conf to accept the registration? maybe a sample config? Thanks /Krystian

hi, maybe someone out there already has some experience and can help me. I have just ordered an E100P card from Digium, I already have a basic asterisk setup up & running. My application is the following : I want to accept incoming calls from the PSTN to Asterisk, and without asking anything of the client just pass them immediately to a call gateway in USA, actually we are planning to use

Hi, I don't seem to be able to get music on hold to play normally. The sound gets often interrupted with a few seconds of silence then starts playing again. I'm using mpg123-0.59r and tried mp3 files with different sample rates with no luck. If that matters, endpoints are SIP ata186, SIP Cisco 7960 and H.323 (over chan_h323) Quintum Tenor. Sometimes it may play fine for a few minutes

Hi All, Is it possible to use Quintum AFT800 on Asterisk 1.4.29 as Trunk for Analog (like Digium Analog Card) ? And if it's possible, could any one please give me the reference how to configure it on Asterisk 1.4.29. Thanks Regards, Zoel Hairi -------------- next part -------------- An HTML attachment was scrubbed... URL:

My fellows, We have Asterisk@home installed and we want to interconnect it with our existing quintum gateways.. any idea how to config that? Your time is very much appreciated.. Cheers, Jessie -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050220/2518797c/attachment.htm

Hi. I'm trying to configurate Quintum AX to work with Asterisk SIP egister/Proxy server and my problem is that only the first user account get logged in and only that user is able to make call correctly. It seems to be a problem with authorization - I have noticed no "Proxy-Authorization" information in SIP INVITE, ACK, CANCEL messages. I have also noticed that when I remove

I just upgrade quintum A800 with new SIP firmware ---------- Product Name: Tenor Analog A800 Multipath Switch - 8 ports (Rev. B) Gatekeeper Status: Mini GK Calls Allowed: 8 Feature Bit Status: -PS/+RB/-ER Languages allowed: 1 Serial Number: A002-00308F Ethernet Address: 00-30-E1-00-30-8F IP Address: 10.101.0.10 Subnet Mask: 255.255.255.0 Default Gateway: 10.101.0.1 System Software Version: