similar to: clearing "stuck" channels without a restart

This is not an Asterisk specific question but doesn't anyone know if you can automatically prepend a 9 on the call lists so clients can return dial without having to repunch in the number? If you go to directories now it just shows the number without a 9 (obviously). Maybe on the Asterisk side?? Bill -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have a situation that has repeated itself a few times. Someone calls into Asterisk and is connected with a voice extension. At some point during the call, the log shows "chan_zap.c: DTMF digit: f on Zap/2-1". At this point, the call is redirected to receive a fax and the Asterisk voice extension is hung up. The users report that there were no noticable tones heard just before the

I have read that 1.4 has shared line appearances, which I assume will work with Polycom phones. Has anyone configured this and verified it working? I was going to start playing around with it but wanted to see if anyone else has tackled it yet. Bill -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am testing out hylafax and iaxmodem. Submitting jobs to the hylafax server and having it then dial using iaxmodem is working fine. Hylafax server is talking to my Asterisk box that has a Sangoma A101 in it via iaxmodem via an IAX channel using ulaw. A call coming into a certain test DID comes into the Sangoma A101 then it goes to another box via IAX ulaw that uses the rxfax app to

2 Asterisk servers 1.2.12.1 Connected via IAX2, same switch, GigE, no packet loss, etc 1 with a Sangoma A101 for a PRI to the PSTN Ulaw QoS enabled NAT for the registered ATA boxes, no nat between the * servers Faxing inbound: Call from PRI hits the first Asterisk server Then talks to the 2nd via IAX2 NVFaxDetect receives the fax, converts to PDF and emails it out Works great!

I've been playing with Asterisk for a few weeks and it's working great. I have a question about getting multi-line receptionist phones working. I was thinking about getting one of these expansion ports: http://www.cisco.com/en/US/products/hw/phones/ps379/products_data_sheet0 9186a008008883d.html What are people using for receptionist phones that show all the extensions in

Hi all, I install the last version of Asterisk and I tried to send faxes, but nothing works. Here is my configuration: Analog Fax <----> IP <----> Asterisk <----> IP <----> Patton M-ATA <----> Analog Fax 2 I tried Analog Fax 2 -> Analog Fax but nothing works!! In the Patton configuration I put G711 and no silence suppression. In asterisk I have

Background, Client - realtek rtl8111c tftpd version is 5.0 options on use -l -v Client: PXE-EX32 TFTP Open Timeout Server: Jun 12 10:48:38 damar in.tftpd[30132]: RRQ from 192.168.1.107 filename gpxelinux.0 Jun 12 10:48:48 damar in.tftpd[30133]: RRQ from 192.168.1.107 filename gpxelinux.0 Jun 12 10:49:24 damar in.tftpd[30134]: RRQ from 192.168.1.107 filename gpxelinux.0 Jun 12 10:50:36 damar

Using AMP, the configuration I have used to work fine with Broadvoice. Now it gets a busy signal every time. I've checked "sip show registry" and it says it's registered just fine. I've tried "sip debug" and it shows calls coming in, but they always get a busy signal & I can't tell why. Here's a SIP Debug output: Sip read: INVITE

Hi, I'm trying to track down why I'm getting calls dropped on an infrequent basis between two asterisk servers which are at the same physical location and connected to each other with UTP ethernet. Here is the connection diagram Asterisk Server 1 ===UTPENET== Switch ====UTPENET==== Asterisk Server 2 I see sporadic RX and TX frame retries when I enable iax2 debugging on either box.

Hello, I am trying to setup a Grandstream GXP2160 IP-phone with secure calling (SRTP). Secure signaling SSIP for registration is working great ! I follow this guide : https://wiki.asterisk.org/wiki/display/AST/Secure+Calling+Tutorial But when I try to make a call with SRTP, I get stuck. There is an initial INVITE which is anwered with a 401. There should follow a new INVITE with a nonce,

What settings are people using? I've seen the ones from dslreports but I'm in that lucky group of people that paid the 1 euro just to have it no longer work. Even after I setup a additional account over the weekend it still doesn't work. And, of course, etherreal only shows encrypted traffic so I can't snag any config settings from it. Any assistance? -----Original

I have some stuck channels that I think I'm going to have to bounce Asterisk to get rid of, but am curious to know what they are and how they've managed to accumulate. The show up with a channel identifier of '(None)' as in the output below, and do not show up in the soft hangup list, and so can't be cleared by that method. Here is the output from iax2 show channels:

Hello all I've discovered that SIP channels sometimes get stuck in *. I've read some posts from Fri 29 Aug 2003 which mentions this issue, but there doesn't seem to be any final answers I don't know if this is related to the 0001604 bug? Below is a list from one of the incidents: I know the (d) means that it is scheduled for destruction but the 10.1.1.45 channel hasn't

Hi, I've have followed through the help docs in trying to get an initial setup going with two phones and the asterisk server. Firstly, all I'm trying to do is get the two phones actually talking to one another VIA asterisk.. I've added this to sip.conf: [phone1] type=friend host=dynamic defaultip=192.168.1.106 ;username=blah ;secret=blah dtmfmode=rfc2833 ; Choices are inband,

Hi, I am using Trxibox 2.6 latest ISO install. Following is the output of : "sip show channels" [trixbox ~]# /usr/sbin/asterisk -rx "sip show channels" Peer User/ANR Call ID Seq (Tx/Rx) Format Hold Last Message 212.53.40.40 0218245 6cfb845d050 09011/00000 0x0 (nothing) No 192.168.1.116 (None) YTc4ZmM3NjV 00101/00006 0x0

I am using a2billing as calling card platform with asterisk 1.2.17. After running for several days, if I issue 'sip show channels' command, I got a lot of dead sip channels although 'show channels' command only show 5 channels. What cause these dead channels? How can I clean out these dead channels? Will they pose any problem to my * server if left alone? What does this (d) mean?

hi, I use IAX softphone with asterisk and I notice that a call between two IAX softphones end after 1 min. Then I can't hear anything but the call still in progress. I have this log in asterisk IAX debug: Rx-Frame Retry[No] -- OSeqno: 002 ISeqno: 002 Type: IAX Subclass: ACK Timestamp: 00016ms SCall: 21589 DCall: 00001 [192.168.1.22:4569] Tx-Frame Retry[000] --

Can someone recommend the best way to view current calls in progress on the Asterisk console? Neither the 'show channels' or 'sip show channels' commands are easy to read. hestia*CLI> show channels Channel Location State Application(Data) SIP/2944093-f9e2 (None) Up Bridged Call(SIP/2944079-e7f2) SIP/2944079-e7f2

Hello all, I am looking for a way to restrict users from logging in two separate phones with the same authorization name/password at the same time. Meaning, I only want users to be able to place a call from one phone in one location, but have the ability to move from computer to computer. Has anyone found any sort of solution for this type scenario? Thanks, Bryan Mahin Please visit us @