similar to: Granstream GXP2000 Distinctive tones

Does anyone know how to set the distinctive ring on the Linksys SPA941? I want to be able to dial one extension and have the phone ring with a certain tone and then dial another and have the phone ring with a different tone. I have tried the following ------------------------------------------------------------------- exten => 802,1,SIPAddHeader(call_info=Classic-4) exten =>

Hi I have a grandstream gxp-2000 and trying it on an asterisk 1.6. When I call internally between extensions I can hear the other person in the gxp2000, but when I call externally from the gxp I can't hear the person on the other end, but he can hear me. How do you configure the grandstream 2000 to work on asterisk 1.6? Regards /ralf ________________________________________________ Ralf

All, I have AAH 1.0 installed using Digium TDM04B and Grandstream GXP2000 phones. All seems well other than the phones have to be reset up to 5 times per day. It is like they lose thier ip connection or maybe thier SIP connection. Has anyone else experienced this issue? I have the phones set for static IP addresses and that doesnt seem to help either. Any help would be greatly

Version - Asterisk SVN-trunk-r12793M (1.2.4) I have 4 Grandstream GXP 2000 phones configured. However at the moment, I have had to disable BLF, Hints, and Call Limiting due to an extremely annoying bug which seems to make the phones channels "lock" in busy after a call has been hungup. If I do a show hints after say extension 200 has hung up I get the following -= Registered

Asterisk 1.0.7 Has anyone got the hint function working, and maybe with the GXP2000. I am testing with 2 GXP2000 phones (firmware 1.0.1.9) at the moment trying to get the LED's to light up. On ext 690, button 1 is setup for ext 691, I did this using both methods 691, and <sip:691@192.168.69.1> On ext 691, button 1 is setup for ext 690, I did this using both methods 690, and

I am trying to set up the BLF on a GXP2000. Currently what I have is extensions.conf: [globals] polycom430=SIP/101 [internal] exten => 101,1,Macro(voicemail,${polycom430}) [macro-voicemail] exten => s,1,Dial(${ARG1},10,tT) exten => s,2,VoiceMail(u${MACRO_EXTEN}@default ) exten => s,102,VoiceMail(b${MACRO_EXTEN}@default) [ext-local-custom] exten => 101,hint,${polycom430}

I have 20-30 GXP2000's connected to * over a T1 line. Neither end is NAT'd and there is plenty of bandwidth available over the line. The GXP's are 1.1.5.15, which is the latest. I have a problem where the phones keep dropping off of * and I get a "failed to register" message in the log of *. Sometimes they eventually connect and sometimes, I have to reboot them to

Hi All, I have tried searching everywhere but I cannot find a definitive answer as to if and how the conference button works on the BT100. Could anyone be kind enough to fill me in on some info on how to use the conferencing feature, as well as any configuration in asterisk thats needed, on this phone? Thank you, James -------------- next part -------------- An HTML attachment was scrubbed...

Can anyone who has used both comment on the pros and cons ? Need to buy about 30 of these, for a small company with limited IT support. Julian ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please visit http://www.messagelabs.com/email

hi all, I known taht this ML is about *, but lot of you are using BT telepnones. I'm using FW 1.0.6.7 for all phone. This firmware support VLAN tagging for QoS on the Layer2. I use it to separe the PHONE network form the PC network, which are in PC connector in the BT. And I also use the TFTP server for provisioning (software, configuration). The problem is, if you set the VLAN for QOS.

Is there an official list anywhere specifying the Prerequisites for installing asterisk(Specifally 1.4) on Fedora Core 4? I have been struggling with a "configure: error: termcap support not found" error when compiling 1.4 on my brand new install of FC4 fully updated, Fedora was installed as a base install to try and keep the overheads down of running a full GUI and all the other junk,

To all: (newbie) I have setup a BT 100 phone and mostly everthing is working pretty good except for the message button. I have place value in the appropiate field in the web configuration but nothing seems to work. When I press the button the speakerphone led goes on but the phone does nothing else (no dialtone, no sip request to *). Does anyone have this buttton working? I would like to

I have 5 GXP 2000's with firmware 1.1.4.25 running with Asterisk 1.4.13. Is anyone else getting the following error in the asterisk console: [Oct 22 11:39:01] WARNING[7100]: rtp.c:1142 ast_rtp_read: RTP Read too short every couple of seconds when a handset is in a call? I didn't notice this happening when I was using an older GXP2000 with the same firmware (doesn't mean that it

Hello, We have several clients with GXP2000 in their network and behind NAT. We have one particular client that has several GXP2000 behind a Linksys RV082 VPN Firewall/Router which is doing NAT services. According to SIP packet inspection, it detects it's a symmetric NAT. The problem we have is that even though we have configured Asterisk AND the GXP2000 to register every 60 minutes, they

I've tried to use a Cisco power injector to supply power over Ethernet to a GXP2000 phone without success. Although when I plugged these phone to a PoE capable Cisco Switch it worked without a problem! Knowing that all these three equipments implement IEEE 802.3af protocol, why doesn't it work with the Cisco power injector? Anyone also had this problem before? Thanks, Ricardo Carvalho.

1. We just dial the extension directly and have speed dials setup for the first 6 parked positions. We don't use *8 at all. 2. Change the config on the phones under Account to "Send DTMF via RTP (RFC2833)" -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Noc Phibee Sent: Thursday, February 08,

Hi i use a lot of Grandstream GXP2000 with BLF How to set up on the same key BLF blinking call interception? So that someone is able to take a call that is destinated to another user phone Thanks bye

Hi i have two problems with my Grandstream GXP2000 : 1- When i wan pickup a call, that's don't work's (*8EXTEN) and when i test whit Softphone, i have a error too, he say me *8201@MyContext not found .. in features.conf, i have: [general] parkext => 700 parkpos => 701-720 context => parkedcalls

Hi all gusy, i have a big problem with gxp2000 and asterisk 1.0.9 The phones after a few go in "busy" state, if you call it get the busy tone but the phone can male any type of call. This is my sip.conf [502] language = it username = 502 secret = <password> host = dynamic type = friend context = local canreinvite = yes dtmfmode = info callgroup = 1 pickupgroup = 1 callerid = 502

Hi, what's thereal use of cfg.txt file during Grandstream GXP2000 provisioning? Thanks -- Domenico Viggiani