similar to: ANI and DNIS Seperation on a PRI (TelephonyNumbering Plan (E.164/E.163) (1) '*4105556654*8005550215*' ])

OK I am going to do it again. Global Crossing is now sending ANI but it is not in the format I expected. Any one know of a way to get this data into two seperate variables? The first number is ANI and the second is DNIS so it is "*tendigits*tendigits* on one line like below. < Called Number (len=26) [ Ext: 1 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan

Alexander, Thanks a million, you really saved me some time on this one. -----Original Message----- From: Alexander Lopez [mailto:Alex.Lopez@OpSys.com] Sent: Mon 4/10/2006 1:11 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Subject: RE: [Asterisk-Users] ANI and DNIS Seperation on a PRI(TelephonyNumbering Plan (E.164/E.163) (1)'*4105556654*8005550215*' ]) from the

Is there a setting somewhere in * to define whether I am receiving callerID or true ANI? Global Crossing claims they are sending ANI but I dont think so. My understanding of ANI is that it is always sent, regardless if callerID is blocked. If I dial *67 and my DID, I get "Presentation: Presentation prohibited of network provided number" and no number. Before I call GC on Monday

Hi all, I have to asterisk-1.0.9BRIstuffed-0.2.0n boxes each equipped with a TE410P. Box A is connected with pri1 to the PSTN. Box B is connected with pri1 (cpe) to the Box A at pri2 (net). Now I want Box B to dial out to the PSTN tunneled thru Box A and have it get all ISDN indications in case of call failure, eg. unallocated destination number etc. But currently Box B always gets only

I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (just one!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR some time

handled. So....what do I do? Thanks, MD =1=================================================== !! Invalid Protocol Profile field 0x11 -- Accepting call from '2004000' to '111' on channel 0/23, span 1 -- Executing NoOp("Zap/23-1", "Incoming call from Meridian1") in new stack -- Executing NoOp("Zap/23-1", " From number: 2004000|

I've a call center using IAX softphones provided by a third party. We've observed problems where the IAX phones seem unable to use our PRI trunks. A sample anonymized call is provided below with the PRI debug calls embedded. Any thoughts, comments or suggestions would be welcome. In anonymizing it, I preseved the format and number of digits sent. -- Accepting AUTHENTICATED

picture. I know the firmware on the Nortel is old, so I'm guessing that libpri is sending something that the Nortel does not know how to handle. Is there a way to dumb down what libpri sends? From everything I've read PRI is an evolving standard - and older devices may struggle with newer extensions/developments. (This might be very handy for users trying to talk to old pbx's.) Is

Salve, I'm somewhat stuck on how to get DTMF working with my setup and googling didn't yield anything similar. My setup consists of one CAPI-capable board (AVM Fritz!DSL) connected to a BRI (T-ISDN), one HFC-S board running in NT-mode connected to an internal S0 bus with some ISDN devices (DECT stations, TA) and, of course, some ethernet interfaces. ISDN standard used is Euro-ISDN.

Hi Folks, I've Asterisk Bristuffed up and running behind an Auerswald Commander Basic ISDN PBX on the internal ISDN Bus (BRI/PTMP). The HFC Card works marvelleous for outgoing calls (as the parallely installed avm fritzcard with chan_capi does), but when I'm trying to call in, I get a short ring signal and then the connection is terminated. This does not happen with chan_capi and

Hi all, I have some problem to send a FAX to a given number. I use asterisk 1.2.18, on a openSUSE 10.2, i586 host. The FAX is sent out via an ISDN PRI interface, I'm in Germany, and the destination FAX devices are in Germany too, but in different areas, so I have to use a city prefix. I did set the pri device in debug mode, below are two calls, to two different FAX numbers, the first is

Hello List I'm trying to figure out what is wrong between my asterisk and my NEC 2400 pbx We have been trying to link them with a spare PA-24DTG from the NEC, I'm able to call an extension on the Asterisk, however the extension rings, and then immediatly hangs up I traced it back to the debug of the PRI on the Asterisk... I would appreciate if anyone could pin point what is wrong The

Dear Gurus, i am facing some unknown problem here.. first, let me describe my case. my office is using a nortel merridian option 11c PBX. and it is connected to the provider thru a E1 card, which is working fine with no problem. my plan it to slot in a server with 2 TE11XP card to intercept the outgoing calls. Provider <--te11xp---> asterisk <---te11xp------> nortel merridian

Hi all, I'm debugging a PRI problem, i can see the calling number but i get a busy all the time. From the output below, I guess asterisk hangs up immediately. Can anyone point out what the problem is? Thanks in advance. *CLI> < Protocol Discriminator: Q.931 (8) len=32 < Call Ref: len= 2 (reference 4865/0x1301) (Originator) < Message type: SETUP (5) < [04 03 80 90 a3] <

Hi, Ive been playing on a asterisk to orion gsm box E1 pri setup. I have achieved incoming calls to be passed to my asterisk box successfully but outgoing calls will just I have tried playing with various pridialplan and overlapdial settings and with no success. If anyone can make more sense from the log, I'd certainly appreciate it. I am sending a 10 digit number to be dialed. I guessed

Hello, I have a problem, and I'm looking for you help. When I dial certain number my calls are getting dropped. I initiate the call, I hear IVR, then I am being transfered to operator, and then suddenly I get ISDN DISCONNECT message. I had this type of problem some time ago, and I thought it was a problem on the other end. But now this is a second time it occurred and I want an expert to

Can someone in Asterisk'land subscribing to 800 service explain to me how to setup extension.conf to route calls based on the incoming DNIS/ANI. For example I want to route 3 incoming 800# coming across a trunk group to all land in the same queue. So I guess I am asking how to perform DNIS/ANI based call routing? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Good Day list, Need assistance determining the best place to read up on whether Asterisk can help me out. I have a situation where I need to do the following <PRI from Telco> ------- <Analog Channel Bank>------------<Proprietary Box> | | | | | | <PRI Port 1 of Digium Quad T1> <PRI Port 2 of Digium Quad T1> | | | | | |

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

Hi all, I am using a Sangoma with two PRI's. As far as land phones, the calls are fine but it refuses all cellphone calls: My configuration in Zaptel is span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 span=2,0,0,ccs,hdb3,crc4 bchan=32-46 dchan=47 bchan=48-61 and on Zapata.conf: [channels] language=it context=default switchtype=national