similar to: Asterisk/InterTel Axxess via MGCP? Anyone?

I have a handful of Linksys PAP2-NA's all talking nicely to Asterisk using standard telephones. I've been running them for the better part of this year. No complaints whatsoever. We chose the PAP2-NA's mainly due to cost and especially the ease of provisioning. In an effort to inexpensively bridge our office PBX (InterTel Axxess) to our VoIP network, we've opted to connect

Hi all, My office recently purchased an InterTel Axxess system with the IPRC card for VoIP. To our suprise, this card allows the InterTel endpoints and MGCP endpoints to work, but not SIP clients. I was really expecting to get a SIP softphone working with this setup, but that appears to require our vendor to sell us a SIP gateway and licenses at a not yet determined price. With this

Has anyone successfully integrated Asterisk with an Inter-tel Axxess phone system via a SIP trunk using the IPRC card? -- Marvin Horst -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20101006/5dbe435a/attachment.htm

Greetings all - I'm interested in using an asterisk box to supplement and add VoIP capabilities to our legacy InterTel Axxess PBX. After searching through the list archives and through google, it seems that the best way to go about this is to connect the two systems via a T1. Is this correct? The PBX currently doesn't have any VoIP capabilities, so that's not an option for

Hello - I have (finally) obtained a fair amount of success in connecting my Intertel Axxess PBX to an asterisk box via a T1 PRI. I can place calls from the Intertel side through the T1, out to an IAX2 softphone and the calls get routed correctly and all of the CID information stays intact. However, when I call from the IAX side to an extension which should route back through to the Intertel

Hi everybody, Well, I've finally got asterisk to to talk nicely with my Intertel pbx. Currently there is a outside T1 line (e&m wink start, esf, b8zs) connected to asterisk, and then asterisk connected similarly to my Intertel pbx. For right now all asterisk is doing is passing calls between the two. When I call out from the pbx, I can connect perfectly to the outside world. When I

I have asterisk FXO module on a TDM400P hooked to an Intertel Single Line Card. I can place Intertel intercom calls to Asterisk (both SIP and analog phones) and the reverse, but transfering calls doesn't work. Here what the transfer looks like: Intertel FXS > Transfer > Asterisk FXO > Asterisk FXS > any extension When the call is answered Asterisk hangs up. Intertel

On Wed, Aug 03, 2005 at 11:28:19AM -0500, asterisk-users-request@lists.digium.com wrote: > 10. Inter-Tel AXXESS failure: HDLC Bad FCS (8) on Primary > D-channel of span 1 (Gavin Hamill) > Date: Wed, 3 Aug 2005 15:32:48 +0100 > From: Gavin Hamill <gdh@laterooms.com> > Subject: [Asterisk-Users] Inter-Tel AXXESS failure: HDLC Bad FCS (8) > on Primary D-channel of span

Yep, another list posting on this topic :) All the messages I've read on this are from people experiencing these errors in quiet times - I get them as soon as I plug a port on our TE410P to an Inter-Tel AXXESS PBX.. and I get them continuously... I'm just sticking an * box in between ISDN30e (we're in the UK so euroisdn) and the PBX.. and whilst the telco ISDN30e side works like

Hullo :) Can someone help me untangle a bit of a mess? I'm trying to set up a demo * server to show off how useful it can be to our business (as an IVR system and VoIP backup if our ISDN30s fail). I've not been able to get NT mode working with our InterTel Axxess PBX, so I've resorted to using normal TE mode and working on the basis the people dial one of the ISDN BRI extension

I've been trying to figure out if it's possible to connect Asterisk to a parent Inter Tel Axxess system through the MGCP protocol. The archives for this list aren't searchable and I'm wondering if anyone has a simple answer... Dustin Moore

On Wednesday 03 August 2005 17:33, Jens von B?low wrote: > Gavin, > > >> Any ideas/advice would be warmly received right now! > > You are not going to like my response... Erk :) > The only way I could get this to work (luckily I had 2 identical sites and > was busy with the upgrade to the gen2 card) was to downgrade to zaptel > 1.0.7. Alas no - just moved down to

-----Original Message----- > -this is very true, however, the current version of the Axxess software > (9.0) supports SIP trunking natively on the IPRC. I just got my Axxess > upgraded and am salivating to get * connected to it. Hmm, so 9.0 is out and it supports SIP natively. How did you plan to integrate the 2? -The Axxess will see the * as it would see an IP service provider.

Is it possible to act as a middle man on a T1 line? My installation currently has an aging Inter-Tel Axxess box with a T1 coming in (16 in, 8 out). Rather than adding and replacing phones and cards as they die, I would like to slowly migrate to a asterisk SIP installation. I want to take the incoming T1 line, use any available outgoing lines for outgoing SIP, intercept any incoming lines and

I'm having trouble getting the manager interface to behave properly; specifically the Originate event. If I create an originate event as below, the calling phone will auto-answer (as it's supposed to) but the receiving phone never rings. It will timeout at 20 seconds. Action: Originate Channel: Local/201@from-sip2 Context: from-sip Extension: 154 Priority: 1 CallerID: John Doe

I am currently a new asterisk user I have worked with the old rolm systems in the past. I have been asked to look around and find out how to do a few things in asterisk, either in asterisk itself or with third party software. The features that I am looking for are: 1. A good management application for setup and edit the .conf files for both the exten & voicemail. 2. A receptionist software

Good Day list, Need assistance determining the best place to read up on whether Asterisk can help me out. I have a situation where I need to do the following <PRI from Telco> ------- <Analog Channel Bank>------------<Proprietary Box> | | | | | | <PRI Port 1 of Digium Quad T1> <PRI Port 2 of Digium Quad T1> | | | | | |

Anyone know of a business class sip hard phone that includes a quality display capable of supporting "push" data (maybe Polycom?). Something like... VM: 3 msgs OurStock (1:43pm): 59.5 somewhere on the display that can be updated (pushed) from a server? Rich

Hello All, Just looking some comments from gurus about this proprietary systems and phones: Inter-Tel Eclipse2 Model name: IP PhonePlus I did not find anything useful or reasonable about their products on their website or even in Internet.... except sales. -- Thanks and regards, Vasyl Rublyov

Hello, xen-4.6.3-14.el6.x86_64 is in testing since 5th of May. Isn't it production ready yet? It fixes 3 XSAs... Regards, -- Piotr Gackiewicz Intertele S.A. - operator system?w ITL.PL i DOMENY.ITL.PL al. T. Rejtana 10, 35-310 Rzesz?w TEL: +48 17 8507580, FAX: +48 17 8520275 http://www.itl.pl - niezawodne us?ugi hostingowe http://domeny.itl.pl - tanie domeny internetowe