similar to: zaphfc NT Mode. Extension not recognized...

Hi all I have a very strange problem here... I use a hfc-s card with mISDN in NT mode with an ISDN Phone connected. When I make a call, the phone rings two or three times and then misdn runs into a timeout... I don't know where to set that timeout, but it's way to short for the called to pick up the phone. If the destination phone is picked up, then everything is allright and the

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

I have a "Cologne Chip Designs GmbH ISDN network controller" in my asterisk box, and an ISDN line connected up to it. I downloaded the bri-stuff 0.1.0-RC4a package from junghanns.net and used that to compile asterisk using these instructions: http://www.voip-info.org/tiki-index.php?page=Asterisk%20zaphfc%20install When I try to call my asterisk box, my sip phone rings twice and then the

Hello all, if I try to call from one phone on the internal S0 to another on the same S0 using zaphfc, the bus is hung up. The called phone is ringing, but I can't talk from one phone to the other. The error I get is: -- Executing Dial("Zap/2-1", "ZAP/1/55|15|tr") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1/55 -- Channel 0/1,

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Hi all, I really hope that you guys can help, because I've been tearing my hair out for the past 5 hours on this one. I have a Zaphfc (BRI) card in TE mode connected to the S-Bus of a Nortel Meridian phone system. Phone calls from the Nortel to say MSN 510 are correctly being sent to the right SIP phone. When asterisk dials say Zap/g2/224 (a Nortel internal extension) the call goes

bri-stuff.0.1.0-RC4a on debian sid with 2.6.7 kernel isdn sk: Bus 0, device 18, function 0: Network controller: Digi International Datafire Micro V (Europe) (rev 2). IRQ 17. Master Capable. Latency=16. Max Lat=16. I/O at 0xe400 [0xe407]. Non-prefetchable 32 bit memory at 0xd8021000 [0xd80210ff]. i still receive error messages continuosly (every few seconds) i

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

What happens if you change to: signalling=bri_cpe_ptp -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Alex Sent: 01 October 2010 11:37 To: asterisk-users at lists.digium.com Subject: [asterisk-users] debian/dahdi/zaphfc - Unable to receive TEI fromnetwork! Hello, <snip> # cat

Hi all I don't manage to get asterisk 1.2.5 or 1.2.6 running with the zaphfc driver.... The scripts from junghanns.net do download a very old libpri and asterisk version which is too buggy for me to use. Isn't there an acutal patch to get zaphfc support in *? -Benoit-

Hi, I've been learning asterisk for a couple of weeks now - and it worked for me as faar as standard configurations where concerned (sip/iax outbound/isdn4linux & capi with AVM Fritz!, Digium X100P FXO). Now I recently I'evaluating to use asterisk as a replacemnt for our companies (15 employees) legacy pbx system and I'm experiencing multiple problems with the hfc isdn cards:

I've got some weird behavior on my HFC-s cards. asterisk CVS-06/26/04-21:28:35, bristuff 0.02, libpri 20040510, zaptel 20040623 When i pick up my ISDN phone on Zap5-1 ("3987") and call the external number "1901" it will do so, connect me and everything is fine. In the second, where it tries to attempt the native bridge, the audio will disappear. Using another card

Hi, currently I got the following problem: The system contains a HFC-PCI card, it's running without problems under zaphfc. Now this system also should send/receive faxes. Receiving faxes works with rxfax (spandsp) but txfax is not comfortable enough and doesnt bring the demanded results. So an older external ISDN modem and mgetty-sendfax is used for sending faxes. I'd like to send the

Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :

I've a lot af this waring May 12 18:44:35 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: received TEI check request for TEI = 76 May 12 18:44:36 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 May 12 18:44:42 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: received TEI check request for TEI = 76 How i can resolve it? Thak's Tiziano

I've this error How i can find the problem? Apr 23 12:24:43 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:47 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:48 WARNING[131081]: PRI: !! Got a UA, but i'm in state 1 Apr 23 12:24:53 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:25:02 WARNING[131081]: PRI:

Hi. I'm running some asterisk boxes on different sites, some equipped with a couple of ZapHFC cards, others with Junghanns quadBRI cards. All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6) and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with kernel 2.6.17.3 The cards are connected to Telecom Italia's NT1/NT1+ S/T lines; some of them are point-to-point,

Hello, I am trying to use a HFC-PCI (CCD/Billion/Asuscom 2BD0) card in TE mode to dial-in and out with ISDN. The problem is I can not get the card to dial out with a Zap channel. Dial-in is working. I am using bri-stuff 0.1.0-RC4 (but tried also RC3 and RC2k). I tried all combination of "immediate", "overlapdial", "pridialplan". I earlier also managed to dial out

Hi i've an hfc-s card with last bristuff installed at cli> i'm receiving: Sep 8 12:35:20 WARNING[1109552048]: chan_zap.c:6902 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 received TEI check request for TEI = 77 what is causing them? 10x Maurizio

I have installed two HFC PCI A-cards running zaphfc from bristuff-0.0.2, which seems to work quite fine, but I continously receive the messages "D-Channel on span 1 up" followed by "D-Channel on span 1 down" with a few seconds interval. Why is that? Bri intense debug log and configuration files below. I don't need ztdummy or zaprtc, do I? I get some frame slips as well,