similar to: Ideal Setup for T1/PRI and TE110P - second try

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

I'm ordering a PRI T1 for use with Asterisk and a Digium Wildcard TE405P. The provider is asking me a number of questions about how I want to configure the line. Here goes: 1. Dial Tone - No, Yes - Precise, Yes - SCC 2. Framing - SF, ESF 3. Line Coding - AMI, B8ZS 4. Signaling Type - Ground Start, E&M, Loop Start w/Ring, Loop Start w/o Ring 5. Pulse Mode - DTMF, MF 6. Outpulse Start -

Hi, I'm seeing rather odd behaviour on a new box with TE110P card. I'm running the TE110P span with ccs,hdb3,crc4 in pri_net, connected to a second machine with a TE410P in pri_cpe. The span is idle. I'm using pri intense debug span 1 and can see the RRs going back and forth. So - things are running along with the span showing "Provisioned, Up, Active" in pri show

Hey folks, I'm pulling my hair out on this situation and would welcome some advice: I'm using the AMI Manager to Originate calls onto 2 E&M wink T1 circuits via a T4XXP card from Digium. Everything works fine for about 600(+/- 50) calls then the Manager is suddenly unable to launch calls. Using ZapBarge to listen to the channels themselves you can hear the dtmf digits being dialed,

Hi all, Muppet from the UK asking for help We are just about to have a T1 line installed in our office in Dallas and "Advantex" the supplier has sent a questionnaire asking a number of questions. I have put the question area at the bottom of the email, we will be using Digium's hardware. could anybody help :-) In the UK when I asked for a E1, number of trunks required and the

Hello, Again one more question about hardware. What could you suggest me to buy. I need hardware to connect let's say 4 analog lines. (FXO). This hardware should "talk" to Asterisk of course.. Thanks very much for some advices :) Bartek -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I just got a T1 interface for a AT&T (became Lucent) System75 (uses same cards as Definity). I would take a crack at making a cable but can't determine the pinout for a cable and it is not apparent from the board. Asking you guys makes sense as one of you may have one of these systems. The cable has a amphenol male D50 connector on one end and probably a rj45 on the other. I also

I'm getting unstable behavior with my newly installed TE110P T1 card. It hangs up any incoming call anywhere from 20 seconds to 6 minutes. Frequently, when you call back on our incoming T1 there'll be an automated announcement (maybe from the telco?) stating "we are unable to complete your call at this time". I simultaeously get a yellow alarm on the system and shortly

I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start. ----------------------------------------------------Televantage T1 Requirements: Framing: D4 Superframe or Extended

Greetings, Our telco called last week, saying that a lot of channels on our PRIs are blocked. And with blocked they have the following description in the Siemens exchanges: BBAC BLOCKED BACKWARD This status is set when the partner exchange has a blocking set and the signaling of the trunk (non-CCS7) is able to report this blocking in the backward direction. This status can

Hi it's possible to use a Digium TE110P Single T1 / E1 PCI Interface for supply a E1 link to a old PABX ? Thanks

Hi, I have a problem with polarity reverse this my dahdi config [channels] context=default usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes relaxdtmf=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1

I can only conclude that Samba is an elaborate hoax and here's why. 1) Setup is more complex than Sendmail (it set the standard for complexity) 2) Even the simplest smb.conf causes trouble 3) You can pass ALL the tests in the DIAGNOSIS procedure, AND Samba will still not let you SHARE FILES or SHARE PRINTERS between Windows and Unix but you WILL be able to BROWSE YOUR SHARES (Just pretend

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

We have 2 T1's coming from our phone switch to a digium TE220B. We have managed to get CPN and the extension outpulsed from the switch, but call setups are really slow. Our T1's are set up as E&M Wink, and they send us the last 5 digits dialed followed by the 10 digit calling party number (we couldn't get the switch to be happy with *CPN*+5* to use featd). We are using asterisk

brett@websmyths.com wrote: > Also - an outside chance - make sure Tip and Ring > are correct. You could be getting ground loops - depends on the noise. > I am having noise and slip errors between my TE110P and a legacy PBX T1 card. Could this be the same symptom? The connection is made using a 15 pin serial on the T1 Card side to RJ48 on the TE110P side. I can't determine what the

Hi All, I have installed a Digium TE110P card on an Asterisk 1.2.1 system. Its connected directly to the PSTN. But I am unable to make outbound calls on the zap channels. The light on the card is green. Asterisk CLI shows all 24 channels when I give the command 'zap show channels'. I also noticed that Asterisk CLI shows an incoming call every few seconds on the 24th channel. This must be