similar to: Dialling Problem

Dear List, I am new in this world (Asterisk) and facing a problem . i want to make some group, base on extensions .so that certain extensions could call to certain predefine number only. let me give u all a short example extensions 1,2,3,4 will be group A , extensions 5,6 will be group B . so group A only allowed to call one or certain predefine number but group B could call anywhere.

Dear list i am using Asterisk 1.2.5 with A@H . here is my problem. if i dial a number (consider 79) i have to wait around 20 seconds before my Asteisk box response. now i want to decrease this waiting time . any idea how to do that ? thanks Salaque

Dear all, Anyone can point me how to soft hangup all channels using single command ? I am using Asterisk 1.4.15. thanks Salaque

Dear all, I am really new in this world, In my office i setup a Asterisk and all extensions are working fine . i also add some trunk to route my local calls. As some user needs to call overseas so we are looking for cheap gateway with SIP supported. Now . we found one gateway . they just give me there softwitch's ip and told to me to send my call there. i have no idea how to router my

Is there a way to terminate a ringing call before it is answered? I am speaking of prepaid card application in which you want to make another call, because the current number it is not being answered, and you don't want to hangup before dialling another number. /Obelix

Hello There, I *think* i've setuped the AreskiCC2 Calling Card system right , but i've yet to make any calls out of it , i added a rate card , trunk and defined some rates , generated some users , added 10 dollars in them , okay , now i call any number , it asks me to enter my pin , i do , it tells me i have ten $ , right after that it says sorry you dont have enough funds for this call

Is there a way to terminate a ringing call before it is answered? I am speaking of prepaid card application in which you want to make another call, because you current number it is not being answered, and you don't want to hangup before dialling again. /Obelix

Hi Folks, After going to the paifull steps of installing AreskiCC and finally being able to access the webinterface, connecting to *, importing rates and setting up accounts I am not being able to make a CALL: No matter what number i try to dial I get the same response: The number you have dialed is currently unavailabel. Please enter thenumber you want to dial starting with 1 for local and

Asterisk is an excellent PBX system, and makes a very good endpoint in the SIP chain for all sorts of things -- IVR systems, voicemail applications, automated messages, etc. It has an extremely well-written CDR engine, so many people mesh it with billing applications to produce accurate accounting information. It also is fully aware of the media stream, which means it's capable of cutting

Hi Hekuran I have installed asterisk-1.0-RC2.tar.gz, asterisk-prepaid-0.3.1 and postgresql. When I tried to call from any IAX client to another IAX client and also sip client to sip client it worked fine. And also the cdr table filled properly. Now I tried to configure asterisk-prepaid-0.3.1 with asterisk. I have compiled asterisk-prepaid-0.3.1 and also copy the configure file. I

I am trying to install the Modified Prepaid App. I have installed PostgeSQL, created the tables, etc. Make Install runs ok. The when I try to launch asterisk (asterisk -vvvvvgc), it fails to run. I get the following errors, 1st error: [app_prepaid.so] => (Prepaid Application) == Parsing '/etc/asterisk/prepaid.conf': Found Jun 16 14:27:27 ERROR[-1085267840]: app_prepaid.c:127

Hi, I successfully installed postgres and prepaid application in my asterisk box but after I digited the code I receive this error: ERROR: Function asterisk_authenticate("unknown", "unknown") does not exist Unable to identify a function that satisfies the given argument types You may need to add explicit typecasts -- Playing 'prepaid-no-aaa'

hi, for my multi-tenant pbx, i would like to approach prepaid like this: when a customer dials number, i have an AGI that will determine what country was dialed and retrieve the rate from the rate table, once the rate is retrieved, i will get the remaining balance of that customer nd compute how much time remaining based on the rte and the remaining balance. then i set that as an absolute

Hi All; I used A2Billing, basically it is nice and fine, but management possibilities is not that rich, so a lot of staff are need to be repeated that let the admin facing a problem of the needed time to do the task. Anyone advise for another open source prepaid billing that is rich by the management features? Also, I hope to find an open source Billing (prepaid and postpaid) that can work with

Good evening, Have you got any idea which prepaid application will be the best to do simple prepaid calls with a MySQL storage...? PS: I have a compiled by hand Asterisk 1.4.13 on a Debian Etch Thanks

Not sure if a2billing can be shared here, but ill give a shot If the credit < min_credit the IVR play: sorry you have 0 credit and hangup, I want it to FW me to the IVR to add voucher, please let me know: here is log: [18/10/2010 07:01:12]:[file:a2billing.php - line:75]:[CallerID:]:[CN:]:[IDCONFIG : 1] [18/10/2010 07:01:12]:[file:a2billing.php - line:76]:[CallerID:]:[CN:]:[MODE : standard]

Hi, I have compiled and installed app_prepaid module. But have problem when connect to postgres database. I guess so because after key in card number, it always play prepaid-no-aaa voice file. Anyone succeeded in configuring the app_prepaid for prepaid calling service for asterisk? Please help. Ps: where can I view the log file for this module. Thanks. Tom --------------

Hi: We just setup the Asterisk and it seems to start ok. We checked the log, and beside the timer warning, there isn't other error message. However, we tried both SIPURA and XLite, but their registration is not accepted (timed out and failed). Could someone tell me what's wrong? [message] Dec 10 01:33:22 WARNING[2649]: Unable to open IAX timing interface: Permission denied Dec 10

All; I am looking for a solution a motel that is switching to VoIP. They are especially interested in prepaid services. That is, a resident will come to the office and pre-pay for phone services for their room. When the money runs out, service is shut off, and they need to come down to the office again. Accurate reports are very important. A search on voip-info.org shows several solutions out

Is anyone successfully using asterisk-prepaid-0.3.1? I try to configure but doesn't work. It said that you need to do a few step, copy a few files and that is. Please, if someone has any tips about the configuration, answer me. Sebastian