similar to: integration with Toshiba PBX system

Deat all, I am in middle of integrate Asterisk with Toshiba astrata legacy pbx. Following is my setup *Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX* A =============================================> B C <============================================ D Asterisk PBX and strata PBX connected using back to back E1 cross cable. Physicall connectivity

I set up a TE405P to go T1---*---Toshiba. I have the channels configured, and can place calls from the Toshiba, through * to the t1. Incoming calls work great to *, but if they go to the Toshiba, I get a hangup. I think the * is sending the call to the wrong span. I have 2 spans, span 1 from the T1, span 2 to the Toshiba. The bchannels show as 0/1 through 0/23 on both spans in * when it starts.

Hi steve and All, I'm attaching cat proc/interrupts out put, lspci -bv out put, zapa.conf, zaptel.conf for your information Thanks so much for the feedback and I do accordingly. Hope to get rid off this isue any how. To day also reported 10 call drops within 2 hours of period. fook forward to have your support on this regard. Thanks & Regards, Vidura Senadeera, Network Engineer,

As these problems are very time sensitive and frustrating, I suggest you document each change you make and do them one at a time so you can actually know what the problem was and not introduce new problems in the process. Find someone who is on the phone quite a bit and will give you an honest evaluation of the call dropping situation (unless you yourself are experiencing this issue too).

Before studying your configs, what have you tried so far? Did you change this? Also, try changing your second span timing from span=2,2,0,ccs,hdb3,crc4 to span=2,0,0,ccs,hdb3,crc4. Here is the documentation on voip-info for why it may be the cause of your issues http://www.voip-info.org/wiki/view/Zaptel.conf+span+syntax span definition format:

I have googled, and wiki'ed until blue. Is it possible to put T1---*----Toshiba CTX ? I have a TE405P, with one interface programmed for the T1, I am not sure how to program the 2nd port to mimick the T1 to the Toshiba. The Zapata.conf [channels] switchtype=national context=from-pstn signalling=pri_cpe usecallerid=asreceived echocancel=yes echocancelwhenbridged=no echotraining=400

Hi all, I'm dealing with a Toshiba PBX - DK 40 I think it is...The problem is this: If someone dialing in from the PBX (on one of the two X100P cards) goes into a MeetMe conference...Everything is fine, until they hang up - especially if there's music on hold - the line is held open because Asterisk does not know the far end hung up. I have it set to fxo_ls right now for signalling.

I have a Toshiba DK424 connected via T1 E&M to a TE110P card. Intermittently when a user dials a number I am getting 'getdtmf' errors on the Ast server and the calls do not go through. If they dial the number once or twice more, it works fine and I receive no DTMF problems. On another note, end users are complaining about intermittent disconnects. T1 is ESF/B8ZS - 24 chan. Other

I have recently changed jobs and I now have to administer a Toshiba DK424. I would like to integrate Asterisk with this Toshiba PBX. I am quite familiar with Asterisk but I have absolutely no idea about this Toshiba. To make matters worse the manuals for this system are missing. What I would like to do is place Asterisk in such a way that we can extend the Voicemail boxes and possibly add a few

Hi All, I am new to both Asterisk and PBX stuff. I have 3 Tohiba PBXs in 3 separate offices as follows, Toshiba Strata dk28 Toshiba Strata dk280 Toshiba Strata dk8 I need to install 3 Asterisk servers in these 3 locations and integrate them with each of the Toshiba PBX s. This is to give IP Phones/soft phones to the users and to route these VOIP calls through the PBX to POTS. What are the

> > > Hi, > > > I checked by changing to from-zaptel, but no luck yet. Pls guide me on > this. > > Regards, > vudura senadeera > > > ------------------------------ > > > > Message: 9 > > Date: Fri, 19 Jan 2007 16:47:18 -0000 > > From: "Robert Jenkins" < raj@jrw.co.uk> > > Subject: RE: [asterisk-users]

I'm posting here in case anyone else runs into this and needs some help. I'll probably update the voip-info Wiki pages on Toshiba integration in a bit. Asterisk 1.6 makes things a bit easier than what is on that page. I'm integrating an Asterisk server with a Toshiba Strata system at my office. Right now, it is driving some VoIP phones (Cisco ATAs with analog phones plugged into

Hello, community. Several months ago Toshiba Inc. released a new communicator - "Toshiba Portege G900". All device's features are greate, but in practice things are going another way: communicator is really SLOW. Toshiba users have found that G900 is using nVidia GoForce 5500 Chip in it and it seems like it's working partially, because of an incomplete driver. We have written a

I found some postings from Google (notably from Mark Spencer) about successful integration of a legacy Toshiba Strata system and Asterisk. I am also facing that current dilemma. The general legacy solutions that I can come up with is very easy -- either making Asterisk a "proxy" (or frontdoor) to the Toshiba system, or have it operate behind the Toshiba via regular extensions. I'm

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: zapata.conf Type: application/octet-stream Size: 2410 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20070307/871ac980/zapata.obj

Hi All, Thanks for every one who helped me on this regard. I think i was able to rictify the problem. what i did is remove callprogress=yes usecallinpres=yes and restart asterisk. Today i didn't report any drop calls. Many thanks for Eric. :) I hope this situation will continue. Regards, Vidura. On 3/8/07, Vidura Senadeera <vidurased@gmail.com> wrote: > > Hi, > >

Hi all, I have a potential client interested in an Asterisk PBX, which will allow them to improve their virtual office services, among other things (it's a Business Centre). They currently have a Toshiba DK-40 and 19 DKT 2010-SD phones. The owner has told me that the phones are digital (not in the VoIP sense, obviously). Is anyone here familiar with this particular PBX? Any chance that it

I'm interested in setting up Asterisk as a voice mail system for our Toshiba Strata CTX100 PBX. Our current voice mail system connects to the PBX with four analog extensions. Does anyone have information on how to integrate this kind of system with Asterisk? I've looked at the legacy integration section of the Wiki, but it doesn't seem to have anything about Toshiba systems. ---

Hi all I have a pocketPC Toshiba e750 and I want to make SIP calls from it, but I didnt found any free softphones for my Toshiba. X lite's versions for pocketPC isnt free :( Did someone used before a free softphone for pocketPC? witch one? Thanks Joao Pereira www.fccn.pt

I am planning an * install at my business. It will be replacing an existing Toshiba system (I think it is a 424dk). I was wondering if anyone knows of a way for me to use my existing Toshiba phones to connect to *. I would rather not have to spend the $15,000 to replace all of my phones, but I can't find any other way to do it. Your help is greatly appreciated. Thanks, Robert Jackson