similar to: Sipura 3000 DMTF

Arrggghh. Tearing my hair out here. I'm trying to set up the spa3000 in the UK for my home, and want * to control the dial plan I've googled to no avail. I've read the manual to no avail. Can someone, please let me know what the parameters is the spa and * are to a) receive a call from the pstn b) make a call to the pstn from the phone attached I can make sip to sip calls (i.e. I

My SIP phones can dial out through Sipura SPA3k to POTS for local and 911 calls _but_ incoming POTS calls are being swallowup somehow. Am I on the right track with the code snippit below? sip.conf: --------- In sip.conf the following code is _supposed_ to ring the SIP phones when a POTS line call comes in through Sipuara to Asterisk. [spa3k-pstn-in] ; Pots-line-in from Sipura ; If

My apologies for the off-topic post ... No matter what settings I try, when I dial in to the SPA-3000 on the PSTN line, it picks up the call and immediately gives me a fast busy tone then hangs up. The info tab says under PSTN Line status: Last PSTN Disconnect Reason: PSTN Disconnect Tone which seems to indicate that the SPA thinks the caller has hung up. Since I am in Japan, it is possible

Can anybody show me a working Sipura 3000 setup please? I need to setup one to my * box, ... What are the variants you can setup? Advantage - disadvantage. bye Ronald Wiplinger

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Guenther Boelter <gboelter at gmail.com> schrieb: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA256 > > On 05/31/2015 02:31 PM, Luca Bertoncello wrote: > > Hi list! > > > > Now all works as expected, at least in the simulation I did with > > AsteriskNOW. Hopefully it will work later, when Deutsche Telekom

Folks! I discovered some serious problem with several Sipuras 3000 but I don't know if the problem is with them or Asterisk. Basically, if I call a Sipura PSTN line, when there is a call already in progress, generally I get a 503 Sevice Unavailable, but if I try hard enough, I am able to get through and connect to dialed number. The other call gets disconnected but the originator of the

Darryl Moore <darryl at moores.ca> schrieb: > Ahh. Seen that before! That suggests to me that you don't have your > sip.conf records setup right. > > What's your sip.conf look like? Well, here what I wrote in my sip.conf: register => 00493511111111:MYSECRET at pbxluca/00493511111111 register => 00493512222222:MYSECRET at pbxfax/00493512222222 register =>

Hi, How to accept DMTF tone during ringing mode? Its possible. Regards -Hadi.Salem

Hey, guys I've been working on whether libvirt supports encrypted snapshots,Here are my versions of libvirt and qemu [root@xx ~]# libvirtd -V libvirtd (libvirt) 4.5.0 [root@xx ~]# qemu-img -V qemu-img version 2.12.0 (qemu-kvm-ev-2.12.0-33.1.el7_7.4) Copyright (c) 2003-2017 Fabrice Bellard and the QEMU Project developers 1. assign $MYSECRET to libvirt secret using the secret-define and

Hi, Which DTMF mode do people mostly use? I've tried SIP INFO and RFC2833 but although Asterisk recognises the tones (for feature usage), the tones arent repeated to the end user. So if I call a company that has a menu system, I can't use the menu. Thanks Dan -------------- next part -------------- An HTML attachment was scrubbed... URL:

Bear with me this is a bit long winded. I am having some issues making automated outbound calls over Broadvoice from my Asterisk 1.4.2 server. For reference, none of the below issues happen when I make the calls to VoIP phones attached to the Asterisk server. What I am trying to do is call, using a .call file, out via the SIP trunk we have setup, and when the party picks up use AMD to

Hi, I'm trying to configure 2 parallel sip trunks between 2 boxes. However I seem to have the problem that when making a call from Box 2 to Box 1, it sometimes says authentication failed because it is using the username of the other trunk. Here's my configuration: Box 1: [dp-dp2] type=peer username=dp-dp2 secret=mysecret qualify=yes host=box.2.ip.address context=from-internal [e911-dp2]

Does anyone have a Sipura 3k running, and using the FXO? I've got things working right, but if I try to toss a *67 in the dialplan, it seems the sipura is throwing a 403 forbidden back. For example: exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/${EXTEN:1} works fine exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/*67${EXTEN:1} does not (even if I toss a couple Ws in) I can't

I'm having problems with a new asterisk PBX install. the phones/ATAs are all linksys/cisco. They all worked before with a commercial softswitch. Most of the linksys devices offer auto, inband, INFO and AVT. I'm looking for suggestions. Thanks in advance -- One day at a time, one second if that's what it takes

How can I dial *67 on a Sipura 3000 if I dial from a SIP phone connected on an asterisk server. I always get a message saying that authentication failed for INVITE for sip221@192.168.1.6. If I dial a number without doing *67 it's working fine... sip 221 being the extension of my Cisco phone and 192.168.1.6 being the IP of my asterisk server... I have my outgoing context configure

Anyone know what I need to do to get the FXO port on the SPA 3000 to forward calls to Asterisk? My Asterisk is running on port 5061 and I set the dial plan on the device to forward to s@asteriskip:5061 but Asterisk is not picking it up. I can see on tcpdump traces that the Invite packets do go to through to the asterisk machine on port 5061, but it's not picking them up. sip debug does not

Yes this scenario works on my 2 systems which are at LAN. I made one system as server (192.168.0.20) and registered from other system... it is fine but now there is a different scene. actually there is a registered user named abc at system1 (192.168.0.20) having context [payasyougo] which is used to do outbound calls. we want to use this user's context and account so that when we register

Hi, I am new to this list and this is first time i m posting here. please help me out currently I am working on dialing a sip peer on an asterisk server from 2nd asterisk server. scenario is like this. on my system i am using this peer in sip.conf. [abc] type=peer username=abc secret=mysecret host=192.168.0.20 context=default dtmfmode=rfc2833 ;restrictcid=no canreinvite=yes

We have issues with all of the SPA-2000 ATAs we have where incoming calls from only one of our Asterisk servers do not complete. Details: 1- On the CLI we see that when the call is pushed to the ATA it shows Busy/Congested 2- We can make calls to this same server just fine 3- We can receive calls from other Asterisk servers running older CVS versions of Asterisk with the same exact ATA