similar to: voicetronix and asterisk@home

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Hi there, I am trying to delay sending out DTMF from Voicetronix OpenLine4 to the CO line. The reason being is that Voicetronix sends out the DTMF too fast even before the line is fully established with the carrier. Usually when dialing an 8 digit number, only 7 digits are actually successfully heard by the carrier. Currently, my dial plan is: exten => _9.,1,Dial(vpb/1-1/${EXTEN:1}) Daniel

Hi all, I used to have an OpenLine4 card, but decided against using it due to some problems with hangup detect. Does anyone on the list actively use Voicetronix's OpenSwitch12? What are your opinions on the card? Cheers, Flynn

Hello, Hacker I install VoiceTronix OpenSwitch 12 port PCI Telephone Card, and setting vpb.conf, extensions.conf following My problem is: When i dial to fxo(channel 9-12), it is ok, but when i continue press exten 102, the channel crach with error messages following exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872 Do i ignore some setting for VoiceTronix OpenSwitch12

Hi, I am using a voicetronix OpenLine4. I downloaded a recent asterisk CVS from voicetronix webpage but have had no luck to reduce echo on outgoing calls and for it not to crach on incoming calls. I dont think both problems are related though. Here is an output of what happens when a new call comes in and my voicetronix tries to pick it up and crashes asterisk: > vpb/1-1: Event

Ron, VoiceTronix worked with me last week and backported the new chan_vpb that's in the current HEAD CVS tree to the 1.0 stable branch. So if you are using 0.7.2 or 0.9.0 you can go to the VoiceTronix website now (note that this is very new) and download an Asterisk package. When you download it there is an new chan_vpb.c that needs to be put in your asterisk source code tree. Also there

dear Hackers, i have a voicetronix Openswitch card, and i have been finding it very dificult to get it to work with asterisk. i intend to connect 8 ports to the PSTN and 4 as station ports. problem 1: On running asterisk all i get at first i get : event[9=>[11] station OFF hook] on vpb/1-12 even [12=>[11] loop drop on vpb/1-12 event [12=>[11] Tone detect:GRUNT event [2=>[11] Dial

Hi all, Can somebody help me get my OpenLine4 card running with asterisk@home? I've got my VPB drivers configured, but can't figure out how to map trunks and channels the typical way in the AMP config interface for Asterisk@home. Apparently I'm supposed to use /vpb/1 type commands, but I'm not sure how it should work. I'm relatively new to asterisk, I did a bunch of

Has anyone gotten the voicetronix boards to work with Asterisk, what would it take? Or does anyone know where I can get 4 ports or more fxs PCI cards that do work with asterisk? Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-798-9106 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

Hi all, Just thought I'd pass along some pointers when outdialing with Voicetronix's OpenLine4 card. I was having a tough time dialing out from *, it probably has something to do with chan_vpb.c not waiting to hear the dialtone before telling the card to dial. A quick fix was to insert a "," in the dialstring telling the card to pause before dialing. However when the

Good day all We have a voicetronix openline4 card If someone calls in from the outside the pstn and into the system and hangsup asterisk does not deteck the hangup any Idea why please Help Altus

Hey all, This is a little OT but ... I''m trying to use this the YM4R/mapstraction clusterer with RJS but having a hard time, I can create a working cluster when i initiate it in a controller, but not from RJS. For the proper flow in my app it would be very helpful to be able to do it from RJS. Thanks for the help, Chuck -- *Chuck Fletcher* Email: chuck at chuckfletcher.com

I'm looking for a hosting company who's willing to host a asterisk@home instance for under $100 a month. Experienced and professional asterisk hosting only. Thanks, Chuck

Good day all I'm using sip protocol and a openline4 card.If I dial out of the pstn and hangup a answered call it does not disconnect the connection.It shows there is still a call on the external phone I called but on my side its says i'm not connected.We are using x-ten soft phones Can someone please help me Thanks Altus

I have installed a 6VPCI card from voicetronix's but i can't get astersik to use it! Now looking at the loaded modules the chan_vpb is not loaded- so I assume that is why it is not working. Now I modified my vpb.conf file and extensions.conf, have I missed something Has anyone a installation guide as I am very new to this!! I have had asterisk working with SIP extensions. by dowloading

Before I start ... I know there's been a lot of talk over the last couple of days about the list being slow etc... I understand there were problems and that mail is starting to get through now. Just wondering - should I be surprised if something I sent 48 hours ago hasn't turned up at all? And something I sent about 6 hours ago still hasn't turned up (yet). I'm just curious