similar to: Tape drive problems

I have an IDE based PC running Linux/CentOS4 to which I wish to attach a scsi dlt. The host controller is an Adaptec AHA3940 something that lspci reports as: SCSI storage controller: Initio Corporation 360P (rev 02). I would like to have the system load the driver for this adapter at boot but I have two problems: 1. I am not sure which driver to use; and 2. I do not know how to force

I need to install an HP Surestore dlt on a Centos 4 machine and I am at a loss as to how to proceed. Can someone either provide or point me to an online reference on how to proceed to add and configure a SCSI adapter and tape drive. I have read, but not really understood, the man page entry for st. Does kudzu handle this? Regards, Jim I am a digest subscriber so the favour of an

I ran some iperf tests today and it looks like the etherbridge is the limiting factor on throughput. In the beforetime, I saw great throughput to the VMs; over 800 Mbps. With the bridge, the numbers are in the 400s somewhere. Is this the speed I can expect from the bridge? Is there some tuning I should try, or another way to get more bandwidth into the VMs? This is with xen-2.0, 2.4.27-xen0

Hi, after installing centos 4.2 I've noticed that my internal Seagate scsi DAT 72GB tape drive hasn't been recognised in /media or doesn't show up in gnome when putting in a tape. Do I need to edit fstab first or load additional modules in the kernel during startup? regards, Geert -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I am having issues making my box boot with Xen. I am working with linux-2.6.16.28-xen on a gentoo box. The server is Dell PowerEdge 1850 with Perc 4e/Si, FW 521X. When dom0 reaches the point of scanning the SCSI controllers, it hangs in a loop aic7xxx_dev_reset_returns 0x2002. My regular (non-xen) kernels come up fine with detecting my adaptec scsi controller. Had anyone had the same

Hello, does CentOs 5 supports an Adaptec AHA-2940W/2940UW scsi controller (pci)? Is this controller maybe supported by the aic7xxx driver? I want to install CentOS 5 on my desktop pc but the currently installed pci scsi controller for my scanners (drivers: 2x tmscsim, 1x advansys) are not supported by CentOS. So I am searching for something else. Thanks in advanced. regards Olaf

Hello! Has anyone gotten 4.9R to recognize the "ServerWorks CSB6" ATA controller on a Dell 600SC? How about installing 5.2R on a 600SC? 5.2R recognizes the said controller, but it corrupts data. -- eof

hi all, i want to use a compaq sdlt 320 under centos. the tape drive was already installed and after rebooting i was not able to see it(dmesg | grep tape or dmesg | grep scsi). i add the correct module (modprobe st) but i'm not able to use with mt. the st0 file is missing, can someone help to resolve this issue. thanks ?

Hello, Using Samba 3.014 on SLES9 on a proliant Xeon server. All clients (XP) fixed IP addresses, Ip <> hostname in hosts table. During the boot of a XP client I receive these messages in the log file's Can anybody explain why or what is causing this. Most of the XP clients reporting none of these messages. Jul 6 12:50:24 server4 smbd[27787]: [2005/07/06 12:50:24, 0]

Hi, Is it possible do have fsck to run automatically [without operator intervention], if it was not a clean shutdown. Right now, somebody has to bring a monitor & keyboard and say Y, if not it will not run and verify the drive. This is for remote headless servers. -- Thanks http://www.911networks.com

Hi All, I have a Quantum scalar i40 tape library. I need to configure it to TWO tape partition libraries, e.g., library_a and library_b, so that each library has its own tape drive. Then connect this physical tape library to two different CentOS servers so that each server can see its own media changer and tape drive. I once had a successful configuration on one host but NOT on the other. One

Hi, I simplified the config in my first email, but I actually have 2x4 servers in replicate-distribute with each 4 bricks for 6 of them and 2 bricks for the remaining 2. Full healing will just take ages... for a just single brick to resync ! > gluster v status home volume status home Status of volume: home Gluster process TCP Port RDMA Port Online Pid

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

Hi Friends !!! I have one xen server (debian etch) already in production; there are samba, squid, 2 ldap servers , apache2, postgresql and others, 8 virtual machines at total in a hardware raid5. Now I need a backup system, and i will use bacula with a dell ultrium3 LTO. I would like to know if there are problems with i/o? How can I connect a DomU directly to /dev/st0 of Dom0

Hi all.. I have found some problems on smbfs module in 2.4.18 kernel. I compiled it by myself (not the very first kernel compilation in my life ;-)) and then I have got it. Looks like it touch smbfs module as when I recompile 2.4.18 modules with smbfs sources changed to sources of smbfs from 2.4.17 problem disappears!! My mainboard is Abit BE6 with Pentium III 450 MHz. I am using SuSE 7.3 with

----- Original Message ----- From: Karl Heyes <karl@pts.tele2.co.uk> To: <icecast@xiph.org> Sent: Friday, January 31, 2003 5:29 PM Subject: Re: [icecast] Re: Compiling ices <p>> On Fri, 2003-01-31 at 06:39, Marc Remijn wrote: > ... > > > Kernel output: > > > > invalid operand: 0000 > > CPU: 0 > > EIP: 0010:[<d08e25b1>]

Hi, I have been using Centos since 3.0. I have been upgrading regularly without any major problem. 4.1 to 4.2 has been a total disaster. I ran yum update, it went through and a couple of hours later I rebooted and X froze with the screen just being just fuzz [regular rectangles, orange, green...] and the keyboard froze. Could not do a alt-ctrl-backspace, nor a Alt-F1-6 nor Alt-Ctrl-Del. I

Hi all, I got a USB-HDD, but it doesn't looked like connect and cannot mount it just after PC boot. But insert and remove a usb cable from PC, it connect (with hotplug?) Is there any good how-to's for getting a usb-HDD to auto connect when It is booted the computer? lsmod is following: [lsmod of just after boot] Module Size Used by Not tainted parport_pc

hi guys... im a new asterisk user. i dont understand why asterisk doesnt start. pls take a look at the output below. i could start it a couple of times .. #asterisk -gc Asterisk CVS-v1-0-01/21/05-14:58:31, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com> ========================================================================= [ Booting....................Jan

Hi, Can someone please help me with this? I have just upgraded from 4.7 to 4.8-STABLE and this is what I am getting when I try a tape backup. Please CC as I am not in the list. It was working well before the upgrade (dump -0ua -f - / | gzip -c -9 | dd of=/dev/nsa0). Thank you, Lefteris Tsintjelis Jul 3 22:55:18 ene /kernel: