similar to: Voice Mail woe

Hello, I have setup a test server with asterisk/AMP and have several 7960's connected to it. The asterisk server has a public ip and all the 7960's are behind nat'd routers. When I try to call from extension to extension I get directed straight to voicemail. I do not have any cards installed and instead direct everything to an Ondo server. I have been told it's not an AMP

Skipped content of type multipart/alternative-------------- next part -------------- asterisk1*CLI> soft hangup Zap/1-1 Requested Hangup on channel 'Zap/1-1' == Spawn extension (macro-exten-vm, s-BUSY, 2) exited non-zero on 'Zap/1-1' in macro 'exten-vm' == Spawn extension (ext-local, 220, 1) exited non-zero on 'Zap/1-1' -- Hungup 'Zap/1-1' --

I have an analogue trunk to an AT&T Definity. It has a DISA context defined. From a Definity handset call the analogue port extension 1008 and wait for dial tone from asterisk. It takes between 3&4 rings. Likewise from Asterisk SIP handset <PBX Access No><PBX Extn> takes nearly 10 secs to ring. Is this configurable? Ian Cowley -----Original Message----- From:

Hi Folks, I'm have Asterisk version 1.2.1 with a A101 PRI card. I'm working with the CLEC to bring up the PRI and inbound calls are hanging up at his end after a few seconds. I ran PRI debug but it only gives me minimal insight. " Ext: 1 Cause: Unknown (16), class = Normal Event (1)" He ran a trace and the only difference he is seeing is a "ISDN interface explicitly

Have asterisk@home 1.2.1 The server is on an internal network eg 10.10.10.10 It is NAT'd 1:1 via Checkpoint firewall to external public IP eg 50.50.50.50 The remote IAX2 phone (ATCOM320) is configured to call 50.50.50.50 on extension 1055. Outbound calls to 1055 work perfectly. Inbound calls from 1055 get picked up as if it were an external call (see below) and goes straight to the ring

Hello, I have a TDM400 and currently have 2 of the ZAP Trunks configured on it. Zap/1-1 and Zap/2-1. I am Running Asterisk@home Version 2.4 with AMP version 1.10.010 In my Outbound Routing I have the Trunk Sequence set up so that 0 is Zap/1-1 and 1 is ZAP/2-1 What I see is that when Trunk Sequence 0 is full, it does not open Trunk Sequence 1. I have found that this is true even if I

Ok, I've been trying to figure out why my A@H won't answer the lines when I can call out and the panel shows the call coming in - well something bizarre has happened. I set up inbound routing to ring my extension if a call comes in - and my extension rings but when I pick it up I get a dial tone. The whole time after I answer I hear the phone I originated the call on just ring and ring

Ok, I've been trying to figure out why my A@H won't answer the lines when I can call out and the panel shows the call coming in - well something bizarre has happened. I set up inbound routing to ring my extension if a call comes in - and my extension rings but when I pick it up I get a dial tone. The whole time after I answer I hear the phone I originated the call on just ring and ring

I setup my aah box with a sip trunk at irisxa.iristel.net Incaming it is ok but when I try to dial 8 and the nr where I want to call I get all line is busy. In my log I have these: Feb 22 14:33:04 DEBUG[3156] manager.c: Manager received command 'Command' Feb 22 14:33:04 DEBUG[3156] manager.c: Manager received command 'Command' Feb 22 14:33:19 VERBOSE[2721] logger.c: --

Is there a protocol I'm supposed to use here? It seems that people are asking 100 questions a day and SOMEONE is helping them, and I've posted this three times and not even an "I Don't Know". My third repost: Ok, I've been trying to figure out why my A@H won't answer the lines when I can call out and the panel shows the call coming in - well something bizarre has

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:

I have Asterisk 1.2.29, Zaptel 1.2.24 and Freepbx Setup for a queue up to 15 agents through a PRI line, it was working fine for more than 1 year, suddenly, when there is a load on the queue, the asterisk service disconnects and the calls are dropped. And the service starts again after few seconds, and so on. I am not using fax. I checked PRI by zttool and there are no alarms. The cdr logs

Hi, i got Ubuntu 6.06 installed and theres a problem with asterisk. I've sucessfully installed it with the command: #apt-get install asterisk Then after installing FreePBX i get this error when restarting asterisk: root@hernandezz-laptop:/home/hernandezz# asterisk -rvvvvvvvvvv Unable to connect to remote asterisk (does /var/run/asterisk/asterisk.ctl exist?) After looking at the logs i

I'm using FreePBX 2.5.2.2 with Asterisk 1.6.1.4. If I make a call and then decide to blind transfer them using ## my side of the call is not hung up. Instead it sends me to voicemail. If somebody calls me and then I blind transfer them with ## I am hung up on as expected. I called from 8678 to 28688. I then transferred the call to 8532. Asterisk acts like it wants to hang up, but then

Hi, sorry for the long debug output below. I configured Asterisk with AMP to send the whole number including the extensions of the callers to the called party. Whatever I configure in AMP it looks like it is used, In my eyes it is ok, but doesn't seem to work. 033811234451 is the call id i configured, and it seems to use them, but the caller will only see a 0338189040 instead of my

I am using asterisk version 1.2.6 with Zaptel version 1.2.5. I have a POTs line coming into a Digium TDM01B. It appears to not be getting CID at all. If I hook up a POTS phone to the line CID comes through fine. Inbound and outbound calls work fine but there is just no CID on inbound for this channel.The incoming route for the channel is Zaptel Channel 0. No DID or CID settings applied. My IP

Hello List, I am having a strange issue with a trixbox system we installed for a client, and I would appreciate any help on this one. The issue is that occasionally when they go to answer an inbound call from the Sangoma A200 - there is no one there, and they are presented with dial tone. The calling party is hung up. A bit of background: The client actually has two systems install (one at

OK, i've got asterisk @ home 1.3 up and running with Broadvoice. BUT I have one nagging problem to sort out. When you call my BV # the calling party gets no ring indication, just silence until either I answer the phone, or the call bounces over to voicemail. below is the console output when a call is recieved. what am i missing here? thanks Bernie -- Executing

Hello, i've recently switched over from 1.0.9 to 1.2.3. I've experienced some (to me) weird behaviour. This is the config for an example queue.conf: [654] wrapuptime=30 timeout=20 strategy=ringall retry=5 queue-youarenext=queue-youarenext queue-thereare=queue-thereare queue-thankyou=queue-thankyou queue-callswaiting=queue-callswaiting music=default monitor-join=yes monitor-format=