similar to: Openline4 and asterisk@home

Hi fellows I'm trying to set up an OpenLine4 card to an A@H I made a "custom trunk" and putting a "dial string" like this "vpb/1-1/$OUTNUM$" I configured the outbound routing using "8|." as patern and "NXXXXXX" as dial rule..., but I'm getting an "all circuits are busy now" when I dial "8NXXXXXX" Here is my vpb.conf

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Hello, list, I am using Asterisk with an OpenLine4 card. It worked well with Asterisk 1.0. Then I upgraded the system, Asterisk 1.4 had some problem to compile chan_vpb, but I managed to compile it manually. Still Asterisk does not work because it refused to load chan_vpb module. I had to revert back to install Asterisk 1.2. Then I get a error: asterisk: hip.cpp:793:

Any guidance on how to get my openline4 to get recognized by asterisk@home? I've got my vpb drivers running, but not sure how to add it as a trunk, should it be via zap? or is there another way? Thanks, Chuck

I am a serious Asterisk newbie: just installed asterisk last week and it is now running with our Voicetronix OpenLine4 hardware. All is working as expected with one exception, in the following sequence (extracted from my extensions.conf file): [GetConfirmation] exten => s,n,SetVar(TimeOut=0) ; if timeout and TimeOut=1 then user already timed out once, so hangup exten =>

Hello all, We had an experimental system which works on OpenLine4 telephony card and Asterisk 1.0.9. Customer asked to upgrade Asterisk to 1.4, then we found our problem: At first Asterisk 1.4 does not compile chan_vpb.so. The problem is it tries to compile chan_vpb.cpp to chan_vpb.o and chan_vpb.oo, then try to link them together. I manually compiled it, then make went smoothly. But it

Hi, I am using a voicetronix OpenLine4. I downloaded a recent asterisk CVS from voicetronix webpage but have had no luck to reduce echo on outgoing calls and for it not to crach on incoming calls. I dont think both problems are related though. Here is an output of what happens when a new call comes in and my voicetronix tries to pick it up and crashes asterisk: > vpb/1-1: Event

Before I start ... I know there's been a lot of talk over the last couple of days about the list being slow etc... I understand there were problems and that mail is starting to get through now. Just wondering - should I be surprised if something I sent 48 hours ago hasn't turned up at all? And something I sent about 6 hours ago still hasn't turned up (yet). I'm just curious

Ron, VoiceTronix worked with me last week and backported the new chan_vpb that's in the current HEAD CVS tree to the 1.0 stable branch. So if you are using 0.7.2 or 0.9.0 you can go to the VoiceTronix website now (note that this is very new) and download an Asterisk package. When you download it there is an new chan_vpb.c that needs to be put in your asterisk source code tree. Also there

Hi there, I am trying to delay sending out DTMF from Voicetronix OpenLine4 to the CO line. The reason being is that Voicetronix sends out the DTMF too fast even before the line is fully established with the carrier. Usually when dialing an 8 digit number, only 7 digits are actually successfully heard by the carrier. Currently, my dial plan is: exten => _9.,1,Dial(vpb/1-1/${EXTEN:1}) Daniel

Is anyone using the VoiceTronic Openline4 PCI (fxo) card? I am trying to setup Asterisk using a Digium 40B (4 port fxs) and an OpenLine4 (4 port fxo), however I can't find any examples or post that utilize this card. I have my stations (Sayson 390) ringing each other, but haven't had any success ringing out. I have the OpenLine4 loaded and all of the new drivers working good, just

Good people, Please find attached a first shot at a driver for the Voicetronix OpenSwitch hardware. It does work (ish). After paying $900-odd for it I figured I might try to make it work with Asterisk (could never get enough documentation on Bayonne!) I have problems with the audio quality, and since am new to Asterisk, I could really do with some input. First is that because the

Hi all, Just thought I'd pass along some pointers when outdialing with Voicetronix's OpenLine4 card. I was having a tough time dialing out from *, it probably has something to do with chan_vpb.c not waiting to hear the dialtone before telling the card to dial. A quick fix was to insert a "," in the dialstring telling the card to pause before dialing. However when the

Hi I would like your comments on the openline4 card from voicetronix. I am trying to get one working and find it difficult. I was able to get asterisk working yesterday but now it doesn't work anymore While it worked I was able to make some calls and I heard a lot of jitter Any comments appreciated. Patrick

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Thank you (for spamming) - it was the clue I needed to push this through. Sorry it took me a while (and a google :-) ) to realize you'd addressed my initial query - basically, my loss. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Jason Becker Sent: Wednesday, August 24, 2005 00:36 To: Asterisk Users

Hello, Hacker I install VoiceTronix OpenSwitch 12 port PCI Telephone Card, and setting vpb.conf, extensions.conf following My problem is: When i dial to fxo(channel 9-12), it is ok, but when i continue press exten 102, the channel crach with error messages following exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872 Do i ignore some setting for VoiceTronix OpenSwitch12