similar to: H.323 ( HW PBX to *)

Hello, Thank you for the job well-done. I installed the chan_h323 of the asterisk-1.2.7.1 and with lib pwlib-v1_10_0-src-tar.gz and openh323-v1_18_0-src-tar.gz and I used licensed g729 from digium. However, I am having a very funny behavour. 1. If I send a call on its ringing at the called side but the caller didn't get the ringing tone. 2. if the called picks up the phone, I am

Hi, I am trying to communicate H323 and SIP users. I have configured h323.conf, sip.conf and ooh323.conf. If I am using gatekeeper (gnugk) then I am able to call successfully to h323 users using SJphone. And same for SIP users also. But when I disabled gatekeeper and trying to call using gateway with sjphone then every time whatever number I dial the call goes to asterisk and some computerized

I am running asterisk 1.0.1 with OH323 compiled in. We have a 323 trunk to CallManager with a mgcp controlled pri router. When using sip phones (directly registered with asterisk) to call out the 323 trunnk to PSTN, calls timeout after 3 rings. If I answer b4 3 rings - no problem, otherwise I get "no one is available to answer at this time" on the consoel and it redirects to an

I'm trying to connect an Asterisk 1.6 to an Avaya with gatekeeper (CLAN). When chan_ooh323 first loads it tries to establish a connection with the gk but I it fails. I have the following extract from the ooh323 log. Can anyone give some insight? Thanks! MD 23:02:59:045 Sent GRQ message 23:02:59:045 GkClient Received RAS Message 23:02:59:045 Received RAS Message = { 23:02:59:045

Has anyone had any luck getting Asterisk 1.6.2.13 to register to a Tandberg Gatekeeper? The logs on the Asterisk end seem to show that the registration request is sent, and the Tandberg Gatekeeper responds. However, the response doesn't seem to be what Asterisk was expecting. Here is my ooh323.conf, followed by the relevant portion of the h323_log: [general] port = 1720 bindaddr =

Greetings to All, I hope someone has already gotten this working. I spent all day today trying to get ooh323 and gnugk to run on the same box. After a lot of tweaking to get everything compiled, I got both up and running. I can make calls IAX to H323, but cannot make calls in the reverse direction. I have tried many different configs on the GK, but always come up with the same error. It appears

OOH323 Debugging Enabled -- Executing Answer("SIP/3513-090f7d40", "") in new stack -- Executing Wait("SIP/3513-090f7d40", "1") in new stack -- Executing DeadAGI("SIP/3513-090f7d40", "a2billing.php|1") in new stack -- Launched AGI Script /var/lib/asterisk/agi-bin/a2billing.php a2billing.php|1: line:58 - IDCONFIG : 1

Hi, I'm trying to configure Asterisk as SIP-H.323 Gateway via ooh323, but I have an error relatively to the GK Confirmation message. >From the log: "H323 RAS channel creation - succesful Sent GRQ message Gatekeeper Confirmed (GCF) message received ERROR:No Gatekeeper ID present in received GKconfirmed message Ignoring message and will retransmit GRQ after timeout Error: Failed to

Dear Mailinglist-User currently we`re working with an IP-PBX, based on Asterisk, with SIP, H.323 and ISDN-Capabilities. SIP and ISDN works fine, but H.323 not. In our first test, we started to connect Asterisk to an Cisco IOS-Gatekeeper with the "chan_oh323" (version 0.6.5). We successfully tested in/egress calls without any problems. But when we started to connect our Asterisk

Hello again. I'm stll struggling trying to terminate calls from SIP through Asterisk and throught my H323 gateways... Basically the call is accepted by GnuGK but then dropped with *reason = unreachableDestination <<null>>* I did a *debug trc 10* on GnuGK and looked at the sessions... one from X-Lite through Asterisk... and one from OpenPhone... The one from OpenPhone works

All, I'm haveing a bit of trouble getting my head around H.323 and call routing with Gatekeepers, Zones and intra-zone calls - hopefully someone who is more informed in things H.323 will be able to point me in the right direction...? I already have a mature network of Asterisk boxes dotted around the UK and overseas with hundreds of extensions and our own number-plan/dial-plan in the form

Hello, I'm trying to register with a gatekeeper using chan_h323, I have a Login, Password and a user (telephone) number, This is my h323.conf [general] port=1720 bindaddr=x.x.x.x (my fixed IP) gatekeeper=x.x.x.x (gk ip) allowgkrouted=yes allow=all [xx] (my login) type=h323 e164=111 (my assigned phone number) secret=1111 (my password) context=incoming I'm getting this error when trying

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

Hi all I'm trying to set up Asterisk on FreeBSD 4.9 to route calls to H.323 GK. I have installed asterisk using the ports. It seems to be running OK, but when i try to dial through h323, it segfaults I'm using X-Lite as SIP client, i have set up my h323.conf [general port = 1721 bindaddr = 0.0.0.0 tos = lowdelaydtmfmode = rfc2833 context = Out noFastStart = yes noH245Tunneling = no

I am having a slight issue. I am trying to register 2 asterisk boxes with GNUGK and when I try to add the 2nd it gets denied cause of it saying its a duplicate. How do I change the configs to allow more than one asterisk box register to the same GK? brian This email was scanned by: Mcafee GroupShield ---------------- CONFIDENTIAL DISCLAMER ---------------- All information provided in this

Hello, I installed Asterisk from CVS on Redhat Linux 9 and working with chan_h323 module and g729/g723 free codecs too. My network connection diagram: ---------------------------------------------- X-lite/X-Pro-->Asterisk--chan_h323-->GnuGK--->AS5300-->PSTN boldsoft*CLI> show version Asterisk CVS-v1-0-03/24/06-15:27:08 built by root@boldsoft on a i686 running Linux I can make

All, I've fixed my problem getting Asterisk ooh323 channel to stay registered with my Cisco IOPS gatekeeper, now I need to get dialling working. I have the following: [Asterisk with ooh323] ----h323---- [Cisco IOS GK] ----h323---- [Radio system OpenH323] 192.168.1.5 192.168.1.6 192.168.1.7 the Asterisk box has numbers

Hi there, I am trying to register asterisk to a Lucent's MVAM GK. It is not registering to the GK with both h323 channels(chan_h323 and oh323). The problem is that if I set the GK(in asterisk) through the GK's IP, the GK answers with GCF without it's GK ID, and after that it does not answer to the RRQ, because the RRQ message has no GK ID. And when I set the GK through

I am currently trying to transpose some large panel data set ie transposing multiple rows in into a single column. instead the transpose functionality transposes all rows into columns. my sample data set looks like below: ACCT_NUM ACCOUNT_NAME TRAN_AMT DATE EMPLOYER 101913 GK 7489 30-Apr-10 PENSION 101913 GK 7489 30-May-10 PENSION 101913

<P>Hi all!<BR><BR>I'm trying to set up Asterisk on FreeBSD 4.9 to route calls to H.323 GK.<BR><BR>I have installed asterisk using the ports.<BR><BR>It seems to be running OK, but when i try to dial through h323, it segfaults.<BR>I'm using X-Lite as SIP client, i have set up my h323.conf:<BR>[general]<BR>port =