similar to: RE: Cisco 7960 upgrade to SIP

There is an option that you can add to your dhcp server option 150 IIRC. -----Original Message----- From: "Rich Adamson" <radamson@routers.com> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: 2/27/06 4:37 PM > Has anyone done any integration work with Covad's hosted solution ? I > am considering

Has anyone done any integration work with Covad's hosted solution ? I am considering Covad's hosted solution and want to be able to use Asterisk to develop some other apps. Anyone else tried this ? how did Covad react. I know they use MGCP. Another thing, the Cisco reseller rep tells me if I have a bunch of 7960's setup for MGCP (for use with Covad) I will need to get these

Hi, An Cisco 7960 ipphone has been set to SCCP firmware by one of our students. I want to set it to 7.5 SIP firmware and I've been unsuccessful yet. Firmware versions are SCCP 3.0 (Source: http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon/english/ipp7960/addprot/mgcp/frmwrup.htm#wp1045789) ie: Application Load P003F300 Boot Load ID PC030300 When I browse, phone settings, I see

OK. Now I show my ignorance. What's the difference between a T-1 and a channelised T-1? I see that Covad's voip service (formerly GoBeam) requires a channelised T-1. Then I read recently on the list that many T-1s being installed are actually HDSL....which would be not a T-1 at all...right? Michael -- Michael Graves mgraves@pixelpower.com Sr. Product Specialist

As the thread from the other mailing list he sent this to states, it is illegal to share the file(s) he is asking for. Below is the thread from the sccp users mailing list that he sent this to. <sccp mailing list> 2006/2/28, picciuX In fact: the one you mention is not a config file; it is part of the "Locale-Installer for Cisco Call Manager". You need a valid service contract

I've seen mention of it here and there... does anyone have mgcp working with a 7960? I've gotten the phone to work in "basic phone mode", is that all I'll get, or am I missing something? ___________________________________________________________ Steve Creel screel@turbs.com

Hi I looking a good IAX service for a *emerging * voip provider. Better with a test account to try. Thanks in advance. roberto -- Ing. Roberto Pereyra ContenidosOnline Servidores BSD, Solaris y Linux Soporte t?cnico ISPs Jabber ID: rpereyra@lugmen.org.ar For reliable and professional DNS, use DNS Made Easy! http://www.dnsmadeeasy.com/u/14989 -------------- next part

I am a newbie to asterisk and am trying to send a linux command using extensions in asterisk, for example when I dial 1111 I want to run the linux command "/usr/local/bin/br -c -n 1" (obviously without the quotes). If I SSH into my asterisk box and enter that command, it works, however I can't seem to get it to work from asterisk. I am running Asterisk@home2.2 (I know, I am a

I have set up a new SwissVoice phone and it can receive calls but I cannot make calls out from it. The setup is simple for now, 2 phones: SwissVoice is ext 7726 and Cisco 7960 (SIP) is ext 7999. I can call from the Cisco phone and it rings on the SwissVoice phone but when I dial from the SwissVoice phone I get a busy tone upon dialing the second digit. The log reads as follows: -- Endpoint

The documentation of how to use the 79xx series' phones and features with Asterisk is really hard to find and put together. The higher end phones like 7970 are more like converged PC+phone, a thin client to telephony and network apps. But it's really hard to target it as a development and deployment platform because the docs and techniques are so obscure. There seems to be a fair amount

Hi, in following of a recent discussion I got to work on MGCP with the Cisco ATA186 again, and got it to work very nicely. However, there is a little thing with transfers I would like to get comments on: Call comes in from PSTN and goes to an ATA186 (MGCP) Call is answered and then, using flash, transferred to another extension If the extension is available, there can be an announcement and

Can anyone tell me what MGCP error that I'm getting means? The hardware is a MRP200 in a Cisco 7750 PBX. (Its a FXO blade with 2 slots, first one has a 4 port FXO card and the second has 2 port FXO card. It recognises those correctly, at least to the point of this error.) MGCP Debugging Enabled MGCP read: NTFY 13 aaln/S0/SU0/0@MRP200-S1 MGCP 0.1 X: 1adace42 O: L/hd from

Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to

I'm trying to use a 4 port ATA that was designed for use with MGCP 1.0 / NCS 1.0 -- is the channel_mgcp compat with NCS -- anything I can do to make it compat?? This is what happens - below *CLI> mgcp reload Reloading MGCP == Parsing '/etc/asterisk/mgcp.conf': Found Use EXIT or QUIT to exit the asterisk console == MGCP Listening on 10.1.22.39:2427 == Using TOS bits 0 mgcp

Hi, I have some problems transfering call from phone to phone with my Asterisk. When I dial Flash I can hear for half a second the dial tone, but it stops suddenly. The other phone hear the on hold music and pressing flash key another time I get back to the previous channel. On the asterisk consolle seems to be all ok, this is whant I can read: asterisk1*CLI> -- Swapping 0 for 1 on

Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes

Hey guys, can you shead some light on this? I will copy my mgcp.conf and post below, but here is the problem. I can't get call waiting to work with my MGCP device. I already have one call going, and I can hear the second call come in, I flash over to it, but all I get is a dial tone, * puts the 1st call on mute/hold, but I never get the second, and it terminates. I flash back over and pick

Hello I have a problem with my MGCP voice gateway. I use D-Link DG104S Boot PROM Version 3.0B38-D Firmware Version 3.0T86-D I tried asterisk v 0.7.2 and I am using latest CVS version now. When I dial a number very fast, or when I use a redial function, my asterisk receives coupled digits. My co-worker called number 245005111, these are a few lines of my debug. The identifier of first digit

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a