similar to: Codec order sent wrong from Asterisk

I'm new to asterisk and need some help with getting a SIP connection working. I am trying to establish a termination point/DID number in another country. I am currently running Asterisk CVS-HEAD. My foreign provider uses SIP and authenticates via IP address. I am not required to register my SIP connection in order to send or receive calls. Can someone help me with how to understand the

hi, let me explain in detail, what i have configured and what is happening now: 1st router w724v (Deutsche Telekom AG): - port forwarding, everything to destination port 51000-55999 to device with ip 192.168.2.50 (interface of 2nd router) 2nd router Bintec RS353j): - configured NAT, everything to port 51000-55999 to device 192.168.3.99 (same ports) other direction is totally open. I

Hello. I am in a strange situation. I have two asterisk. Asterisk "A" makes a call for asterisk "B" by IAX. Asterisk "B" recives the call and delivers it to Openser by SIP. The problem is openser printing this in the screen: ERROR: parse_to : unexpected char ["] in status 5: <<"David" <sip:>> . ERROR:parse_from_header: bad from header

Hello: I have this situation: I can make calls internally, I can make inbound calls but I can't make outbound calls. Thanks in advance. These are my devices: * asterisk 11.8.1 = 192.168.1.22 * sipphone grandstream gxp2160 = 192.168.1.5 * gateway audiocodes mp-114 2fxs-2fxo = 192.168.1.4 port 1 (FXS) connected to an analog phone port 3 (FXO) connected to the PSTN These are my

Hello, I am trying to setup a Grandstream GXP2160 IP-phone with secure calling (SRTP). Secure signaling SSIP for registration is working great ! I follow this guide : https://wiki.asterisk.org/wiki/display/AST/Secure+Calling+Tutorial But when I try to make a call with SRTP, I get stuck. There is an initial INVITE which is anwered with a 401. There should follow a new INVITE with a nonce,

Using AMP, the configuration I have used to work fine with Broadvoice. Now it gets a busy signal every time. I've checked "sip show registry" and it says it's registered just fine. I've tried "sip debug" and it shows calls coming in, but they always get a busy signal & I can't tell why. Here's a SIP Debug output: Sip read: INVITE

I have spent the morning on this project, still without success. Summary: Yesterday I inadvertently unplugged my Grandstream phone. I might add I did a rebuild of my s/w from CVS at the same time. Since then, the Budgetone seems to talk SIP just fine, but the RTP being sent to it by asterisk "doesn't make any sound." It was suggested I do a factory reset of the phone, which I

Le 09/09/2016 ? 18:32, Madushan Geethanga a ?crit : > Hi, If you're not using RTP encryption did you uncheck the option in your RTP TAB from identity ? > > This is the log. ex dialling 0 from snom phone > > > <--- Received SIP request (1230 bytes) from UDP:123.231.72.210:33878 > <http://123.231.72.210:33878> ---> > INVITE sip:0 at 54.206.59.252

Hi, I have a strange problem. At a site where there are 20+ phones, there is one phone that cannot make outbound (to PSTN) calls. Each call is dropped after 20s with "no response to our critical packet". Calls to voicemail and internal extensions work fine. I understand that everything points to a NAT problem, but I don't understand how it could be because: 1) It does not affect

Hello, a person trying to call me by my phone number is getting the error 488 Not acceptable here. I googled that error, seems like this error is normally caused by a failed codec negotation, though I have no clue how I could have read this out of the logs. Anyway, my setup is as follows: Asterisk 1.8.13.0 - NAT - Sipgate SIP Provider The user calling me is also using Sipgate and is calling my

Hi, I've one Sipura SPA2000 at home behind a linuxbox with two network adapters (eth0 for WAN and eth1 for LAN) doing NAT/DHCP: ___________ HOME _______________ ____OFFICE ____ SPA2000 <---> Linux Box <--> Asterisk Box 192.168.0.253 192.168.0.1 eth1 200.93.xxx.a 200.93.xxx.b eth0 My problem is when I try to call to any trunk or extention

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'm setting up an Asterisk system which is connected to an Alcatel 4400 PBX. On the * I permit g729 and gsm as codecs. If I try to transfer a call by hitting the # key, I get this messages and nothing happens on the phone: WARNING[30110]: codec_ilbc.c:175 ilbctolin_framein: Huh? An ilbc frame that isn't a multiple of 50 bytes long from

We have a basic application that runs a SIP channel to pick up a call and process it. We are using Broadvoice and it's been working great. We recently rebooted the machine and now when a call comes in Asterisk picks up the call but does not process it. Asterisk seems to send the call back to Broadvoice. Nothing at all has been changed in the configuration to warrant this. Below is the

OK, it stopped working. It turns out the transport and endpoints in PJSIP are ok. I can send an invite from my unregistered snom phone and I can see some activity in the CLI. However, when I dial from my snom to Kamailio and have it pass the message to asterisk, PJSIP seems to ignore the sip messages even though they are there. Is there something wrong in the invite that I'm missing? U

I am unable to get a my Draytek working with our Asterisk server. I can make/recieve calls but get no audio. I have tried the various codecs at the Vigor end but still getting nothing. I looked at sip debug (below) but am new to Asterisk and don't really know what I am looking for. Asterisk works fine with XLITE so I know my installation is ok. Sip read: INVITE

Surely there must be someone here who can help me with this problem. I have spent weeks trying to get this damned service to work with no luck. I have incoming calls working, but no outgoing. If get outgoing working then incoming don't work. I have sent this problem to this list a couple of times with little or no response, and I _really_ need some help to sort it out. I have an asterisk

I'm having a horrible experience getting a Cisco ATA-186 to work with *. I can make calls from the ATA with no problems. However, incoming calls make the ATA ring once, and then the call is disconnected. I have no problems with my Sipura 2000 or my Grandstream phones. I am running 2.16.1 sip code on the ATA 186. Neither * nor the ATA is behind a NAT. They are both on public IP addresses

I'm trying to set up pjsip to work with an obi202 and google voice. But I can't configure the endpoint. pjsip: [obi202-auth](!) type = auth auth_type = userpass password = <mypass> [obi202-aor](!) type = aor max_contacts = 2 ; ===== endpoints ======== [gv-voice](obi202-endpoint) auth = gv-voice aors = gv-voice identify_by=auth_username ;identify_by=username ; I also tried

I am debugging an intermittent issue of missing audio on calls that come from a SIP provider into our asterisk-11.10 installation. Sometimes, incoming calls from this provider work correctly, with audio streaming in both directions. Other times, with the same setup, the calling party is unable to hear the IVR recording from the asterisk installation, although in fact the streaming is supposed to

Hi, I'm trying to setup snom 710 phone with asterisk 13 with PJSIP. inbound is working fine but i cannot dial out. i don't hear anything on the phone and asterisk CLI also does not show anything. my config is. please advice. [2001] type=endpoint context=out-local disallow=all allow=ulaw allow=alaw transport=system-udp auth=2001