similar to: delaying "answer" for a number of rings or an amount of time

Well in my setup I have a few IP phones connected to Asterisk as well as POTS phones on my analog line. When a call for my daughter comes in on the analog line (determined from callerID) I send it to her own voicemail after 20 seconds of ringing. It all works quite well. Here's a step-by-step of what happens below: 1 - a call comes in and Asterisk rings SIP/Brian and SIP/joe for 30 seconds.

No, it will dial like a pass-through simultaneously to sip/iax extensions. If you were to dial out to an analog port though, that would be different. So in essence, you can have all the phones ringing at the same time. Greg -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Brian J. Murrell Sent: Thursday,

http://lists.digium.com/pipermail/asterisk-users/2005-September/125146.html -----Ursprungligt meddelande----- Fr?n: asterisk-users-bounces@lists.digium.com genom Brian J. Murrell Skickat: to 2006-02-02 20:14 Till: asterisk-users@lists.digium.com ?mne: [Asterisk-Users] delaying "answer" for a number of rings or anamount of time I want Asterisk to delay answering the POTS line via a

Hi all, I have the Asterisk set up and 2 softphone (Xlite) set up on two other PC. With the following configuration, I can use one softphone (2000) to call the other one (2001) and/or the voicemail at 2999. Here is my problem: 1. When I dial 9+nxxx-xxxx with one of the softphone to the PSTN via X100P card, I got busy tone. (i.e. I want to use the phone line which is connected to the

Hi all, Any one tried installing Asterisk on Linksys WRT54G? We have but facing problems with SIP to SIP calls. The phones ring and calls are established but we cannot hear any voice at all. I tried allow=all in the general section but did not work. So I forced ulaw. Can any one please check it out and let me know what is wrong? Here are the conf files: Asterisk Version: Asterisk

Hi, I configured asterisk on redhat linux 9 box. I installed two different ip softphones (SJPHONE and X-PRO) and got them registered with asterisk. The call from one phone to another does get routed via asterisk, but there is one problem coming up. As soon as call is accepted by the end user , it is automatically disconnected with the error "cannot align media streams". If I enable SIP

Hi; I have entries as below in DB, mysql> select * from sip_buddies; +----+------+----------+------------+---------+------------+--------+------- -----+------------+----------+------+ | id | name | context | defaultip | host | mailbox | type | regseconds | ipaddr | username | port | +----+------+----------+------------+---------+------------+--------+-------

Hi list, i've problems with my * server and the 4 phones which are linked to it. i've 2 grandstream bt100 with the firmware upgraded to 101, a wi-fi phone (i don't know its brand) and another ip phone i don't know its brand. with this sip.conf : [general] port = 5060 bindaddr = 192.168.100.229 context = default ;x changed from default to sip localnet = 192.168.100.0/24

I have a few SIP phones, Cisco 7960s, and was looking into implementing some compression, ala G.729. I'm looking into purchasing a g729 licenses just to get an idea of performance and voice quality, over lans, wireless and single channel isdn. Does anyone have positive/negative experience w/ getting licenses/support from Digium? Hows the sound quality compared w/ g.711? Is 729 better

When somebody call me on my pstn # cable connected to my fxo card it does not work when I check my computer the following error shows Connected to Asterisk CVS-v1-0-12/05/04-19:46:25 currently running on asterisk1 (pid = 2160) Verbosity is atleast 3 -- Remote UNIX connection -- Starting simple switch on 'Zap/1-1' == Starting Zap/1-1 at incoming,s,1 failed so falling

Hi Everyone, After a fair amount of faffing ive managed to get the 2000w working with asterisk for IP -> PSTN calls (i.e. get the phone to make and receive calls over our BT line). The final solution is to set up outgoing VoIP calls but I now know that without a SIP aware router I can think again! (damn you iptables!) In the mean time I'm trying to figure out why I can't get the

>From what I understand it means that the *hardware* in your computer *acknowledges* the call as soon as it is recieved and then sends it to asterisk dialplan for processing. You would essentially need to put the delay before the call ever reaches asterisk. So this problem isn't asterisk related... if I've understood your question and the answer I found correctly. Regards, Jan

Hi, I am very new to Asterisk. I wanted to know how to retrive the Voicemails. I could see some voicemails assosiated with some extensions. Any ideas?? --------------------------------- How much free photo storage do you get? Store your holiday snaps for FREE with Yahoo! Photos. Get Yahoo! Photos -------------- next part -------------- An HTML attachment was scrubbed... URL:

I've read several other emails and pages on the wiki but none give any deffinate answers. if you have 20 asterisk servers each with 4 pri's, all running RealTime Extensions and RealTime SIPBuddies from the same MySQL server, what prevents you from putting all 20 servers behind a single load balancer? That way all of your UA's can use the same IP to register to; vs maintaining which

I have 2 X100P card and configured everything based on configs here http://www.onlamp.com/onlamp/2004/01/22/examples/config_files.txt I changed the area codes to match mine. When I try to dial out I get app_dial.c:554 dial_exec: Unable to create channel of type 'Zap' A zap show channels gives me this Chan Extension Context Language MusicOnHold 1

hi do u have the sip phones extensions in the extension.conf and are they in the right context (sip-incoming)??? are the sip phone registering to asterisk?? try stop asterisk and reconnect as asterisk -vvvvvvvc to check see them registering... ________________________________ From: asterisk-users-bounces@lists.digium.com on behalf of Sistemista WebSolvingJaa Sent: Fri 7/1/2005 6:43 PM

Hi, I am a newbie in asterisk. trying to configure firefly third party edition to connect to aserisk 1.0.3 im able to authenticate but cannot dial extensions. I have been reading the documentation cant seem to find the correct configs. Attached the error message and configs. What am I missing? *CLI> Urgent handler Feb 12 15:52:05 NOTICE[16537]: chan_iax2.c:5718 socket_read: Rejected connect

Hi All We are unable to hear any voice where as in tcpdum it shows that RTP is flowing both ways ERROR CONDITION --------------- -- Executing Dial("SIP/2001-f6c4", "SIP/2000|20") in new stack -- Called 2000 -- SIP/2000-0ead is ringing -- SIP/2000-0ead answered SIP/2001-f6c4 -- Attempting native bridge of SIP/2001-f6c4 and SIP/2000-0ead Have searched web and

Hrm, All of a sudden for some reason Wait() and Playback() are returning non-zero and its causing calls on my inbound SIP leg not to complete. I'm not sure why -- Executing Answer("SIP/2181-4518", "") in new stack -- Executing Playback("SIP/2181-4518", "silence/1") in new stack -- Playing 'silence/1' (language 'en') == Spawn

Guys, Ok - nowhere near as complex as most of the discussions on here ( ex telco engr for 18 years here).. But thought I'd ask for some assistance. Have just set up my first * Pbx - having a play with it and a couple of Cisco 7960 (configured as SIP) phones. The phones are tftp'ing into the server ok, and picking up the configs all ok. Everything _seems_ to be working, but I