similar to: Gateways

Hi, We're installing an * box next week (pbxtra from fonality) and I'm trying to come up with a solution for remote users that want a phone in their home. I need VPN and QoS capability, wireless support would be a nice to have. Ethernet handoff is fine, i don't need integrated dsl or cable modem... I've been googling and cruising the list and can find bits and pieces

I am unable to get a my Draytek working with our Asterisk server. I can make/recieve calls but get no audio. I have tried the various codecs at the Vigor end but still getting nothing. I looked at sip debug (below) but am new to Asterisk and don't really know what I am looking for. Asterisk works fine with XLITE so I know my installation is ok. Sip read: INVITE

Hi all, I finally got my IPSec tunnel from my Fedora firewall system (running Shorewall 4.0.6) to a remote Draytek Router up-and-running, but I''m having difficulties directing traffic through the tunnel. From the output of "racoon -F -f racoon.conf" and the connection status page of the Draytek I can tell the tunnel is UP, but ping and traceroute requests to several hosts

Hi, Ok.. I know dual NAT is a problem for SIP.. ie. UA - NAT - Internet - NAT - Asterisk What about Multi-NAT where a dedicated public IP is mapped to the private IP of the asterisk box.. ie UA - NAT - Internet - Multi-NAT - Asterisk http://www.draytek.co.uk/support/kb_vigor_multinat.html Anyone tried it? Thanks..

One of our clients has a Draytek Vigor 2920- their natted Snom phones behind it are registered to an Asterisk 1.4 server on an external public IP. I've set QOS, bandwidth management and turned off the SIP ALG via telnet but I'm still having some problems with some of the phones losing registration if Asterisk is restarted. I can see the phones sending SIP REGISTER messages, but they

Hi, Does anybody else have problems like this. I'm in the UK with a 1mb ADSL service from Eclipse. I have a Draytek Vigour 2600 ADSL router. My * box is configured with a public IP address which is presented on one of the switch ports on the rear of the router. When there is some SIP activity, incoming mainly, towards my * box, the router will lockup after a short period?! I've tried

I'm in conversation with Draytek's pre-sales dept.............. Here's the most recent reply: <Hello, We really don't know of anyone who has run an Asterisk server on a Vigor2900. There are doubtless people around, but it's relatively rare. Most people don't run SIP servers. Regards,> All I want to know is, if I buy one of these routers, will it break my setup or

Hi, I have setup a IPSEC VPN using Openswan to connect a Draytek router to a CentOS 5.2/Shorewall 4.2.9 firewall. The VPN establishes OK but I''m getting a problem with packets from the left hand subnet getting masqueraded rather than routed down the IPSEC VPN as though they were going out onto the net. I''ve spent the last day searching Google and so far I''ve hit a

Hai Peter, Chipping in here. > > > Hi Rowland, > > You are right about firewall boxes. At least Cisco ASA is a terribly > (over) complicated device. People who are not Cisco pros should be > warned. Stay away, you will just waste your time, get frustrated, and > get sleepless nights. > > I don't blame the Cisco ASA here. In my case, I hadn't much

On 10 February 2015 at 12:55, jg <webaccounts173 at jgoettgens.de> wrote: > >> Some firewalls have a 'consistent NAT' option that needs to be enabled, >> otherwise you get the symptoms described. >> >> While reading about NAT, I came across this web site: > http://nattest.net.in.tum.de/ > The test tool looks at various NAT related properties and

Hi all! I have the following setup: Phone lines -> traditional PBX -> Welltech 3802 -> VPN -> Asterisk -> Linksys PAP2/Welltech ATA-151 -> phone There is 2 pieces of Welltech 3802 (2 port FXO) connected to 4 (2x2) PBX extensions. Asterisk is a proxy here. Each device successfully register itself. I tried the setup above with Linksys and Welltech devices as well. I setup

Hi, If your cluster's virtual IP is using ip aliasing (eg eth0:0), i think your problem come from UDP flows, they are, in opposition to TCP flows, unconnected, so the IP stack take the shortest route/interface to send them, wich is when this is the default route, the real interface and not the aliased. For exemple if you have eth0 the real, eth0:0 the virtual, you can try to add in your

Hi Centos linux 5.11 server with samba3.6.23-6.el5 with workgroup (not domain) This system has been running for four years with no real issues. There are 9 xp clients all within the workgroup, rather than connected to the domain. The server is used for windows shares and for openwebmail This week I had a problem with the draytek 2820 adsl router. I had to reset it and update to the latest 2014

Hi All, I'm trying to configure 2 GS BT100 connected to asterisk and Welltech 2 ports FXO gateway. I configure WellTech 2ports FXO and GS BT100, both GS BT100 can call each other without any problem but when I tried to call a local extensions connected to my Welltech FXO gateway, I couldn't hear any voice on both ends. I would like to ask if anyone has ever encountered this kind of

Hi, After a long way of problems (shipping, customs, etc) finally I got Welltech working. Here below my comments. - The documentation is poor and have errors - The web configuration is not complete. However is useful for the basic configuration parameters. The command line is necessary for modify all parameters. - The software upgrade is easy. Initially the gw came with H323, we upgrade to

Hi Volker, Jordan Coleman, Murray Taylor, David Kennel, Frederic Corne and Stephen Jones all wrote about the problem of a specified network intermittently reported "no longer available" when writing to a file. It's the same problem which I complained about on April 7. I then assumed it had to do with the presence of a w2k3 server in the domain. The problem disappeared after I

Hello, if you have a Draytek SIP phone, please check if the phone doesn't flood your server with SIP REGISTER messages. Draytek phones are broken and keep sending REGISTER messages after receiving 200 OK (even if expires value is long enough). Several such phones are flooding iptel.org public servers these days. If you have direct contact to Draytek developers, please send it to me.

Hi all I'm fairly new to Asterisk, so be nice :-) I was wondering if anyone has been able to get the Welltech K1000A USB phone working on Linux. I see audio and HID drivers loaded when it is plugged in to my Fedora Core 1 laptop, but that's about all that happens. I've searched all the usual places (FAQ, Google, etc) but not found anything helpful. Asterisk is working fine with

Hello all, We recently configure an asterisk server to use with an VoIP provider to make calls to a PSTN. We use (voipjet, nufone, diamond....) We feel that we haven't got the quality that we hope. Sometimes our calls gets mute, or we feel communication cuts on our phone calls. We have got an QOS router (Draytek) reserving 1/2 of our wideband to the SIP an IAX2 protocols, and an ADSL line

On Fri, Jun 29, 2018 at 3:40 AM Thiago Oliveira <cpv.thiago@gmail.com> wrote: > Hi Ales, > > I would like to prevent the guests from different subnets start a > communication. In other words I have the subnet 192.168.1.0/24 and > 192.168.2.0/24 and the guests from 192.168.1.0/24 cannot reach/talk with > guests on 192.168.2.0/24 at the same host. Is this possible using a