similar to: G729 Commercial Licenses.

Thanks but this is for a test, I didn't buy the first one as it's a non commercial installation. I'm trying to test bandwidth etc so I need to try out how 4 of them handle the link simultaneously, I just don't know how to add a second test license. Dean ________________________________ From: asterisk-users-bounces@lists.digium.com

Hi, all!!! What will Asterisk do in the following case: For example, we have 4 licenses, and have 4 simultaneous calls, using G729. Will asterisk allow incoming calls from peer, that can talk G729 and ulaw, and will it force it somehow to use ulaw in this case? All phones there in LAN behind Asterisk prefer GSM codec, so it does transcoding. So, what I mean is will Asterisk fall back to use

I got my G729 licenses installed. I can make calls out and receive calls and the system shows the licenses are in use, however, if I try to call voicemail.. the CLI shows the files are playing, however I don't hear anything.

I've an Asterisk 1.2.4 installation, where I've also installed the G729 codec license. I'd like to upgrade that installation to 1.2.5, but I'm not sure if I'll lost the license in the process (and if I'll be able to recover it later!!!). Is there any special consideration I've to keep in mind in this case, or should I just run the typical "make + make

Yep I did the same. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Francesco Peeters (Asterisk) Sent: Saturday, 21 January 2006 5:34 PM To: fbraeuer@gmail.com; Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users]

Hello, How many licenses to buy?? : From what we understood from digium website, we must buy as many licenses as the number of maximum simultaneous calls using G729 Codec we wish to make. For example, If we want to be able to make a maximum of 10 simultaneous calls using G729 Codec, we must buy 10 licenses. Is it right? Thanks you

I hope this isn't considered cross posting, i sent the following email to Digium support but figured someone on the list may also have better insight into my questions. I have purchased 2 g729 licenses from Digium for testing and have the following questions; ** My configuration is a single asterisk box configured with 2 g729 licenses and 2 x Cisco 7960 Phones, I have confirmed the

I need a refresher course on how many licenses I need to buy. I have an Asterisk server that receives calls by SIP (G729) and then sends them to the PSTN via 32 Zap interfaces on an Astribank. I cannot remember if the license is per channel or per call so I do not know if I need 32 or 64 licenses for this application. Could anyone please remind me? -- Telecomunicaciones Abiertas de M?xico

I am wondering how the g729 licenses are done during calls. If I have N licenses for g729, and N are in use and an additional call comes in that requests N+1 to be in use, how does asterisk handle that call? Does it dump it? Does it negotiate another codec automagically? Basically what happens to that call, obviously it wont (shouldnt) let you use more licenses than you have available, but

List, I purchased 2 g729 licenses but I can't get it to answer a g729 call from a cisco router with a vwic card. In the debug output below you will see that asterisk thinks it only supports: (gsm|ulaw|alaw|h263) when it should support g729 according to the config also listed below. The real odd thing is I can place g729 calls to the router, just not from the router to *. Anyone have any

Hello Everyone, We are looking to transition our 23 channels from testing/lab into production. During testing we used the free open source g729 license using the instructions found here: http://blog.manhag.org/2010/05/installing-the-free-g729-codec-for-asterisk/ A little more about our setup. All recordings have been converted to G729, all voicemail messages are also in G729, finally

Hello, I am trying to see what I need to do SIP to H323 using G.729. I have Oh323 and SIP working with G711 fine. If I have a SIP client configured to use G729 and H323 client also to G729, how many license should I need to buy from Digium. Many thanks SW

Hi, all I am a pabx vendor from Singapore. Recently we are going to implement a failover solution for our customers using heartbeat, the asterisk server can failover perfectly, however the g729 codec canot work, because it is binded the mac address, we have bought two set of licenses, can you provide us some workaround for this scenario? Regards, Liangliang

hello all, i have problem in using g729 codec. my asterisk version is 1.8.22. when i run "core show codecs" in asterisk, there is a g729 codec in the list so i assume that i can use it for my channels. but connection can not be set when i use it for my h323 channel. i read somewhere that codec g729 is a commercial codec and i should buy its license in order to use it. is it true? if

I have been impressed with the quality and meagre bandwidth of the G729 codec from Digium. I am in a testing phase of our roll out, we are using 5 Asterisk PBXs in various countries to provide connectivity for our employees, owners and family. As we are testing, and our setup is somewhat complex due to the peculiarities of our connectivity, there has had to be a lot of changes to servers, cards to

Hello Everybody, Since I upgraded to 1.4 I always get the difficulties as below, which I have never had in 1.2: [Dec 28 21:05:59] VERBOSE[1734] logger.c: -- Call accepted by 202.153.128.34 (format g729) [Dec 28 21:05:59] VERBOSE[1734] logger.c: -- Format for call is g729 [Dec 28 21:06:00] VERBOSE[1756] logger.c: -- IAX2/VoIPRakyat-2 is ringing [Dec 28 21:06:00] DEBUG[1756]

Hi guys, I got 2 licenses of g.729 and while running the asterisk with Monitor (for recording a channel) and using one channel for the call... I receive this error: WARNING[23826]: codec_g729.c:180 g729tolin_framein: Out of G.729 Decoder Licenses! many times.... it starts only when the call through the Zap channel takes place. while this error is being running on my screen I ran the cli command:

I am trying to figure out the best way to deal with this. I want all of the calls in the network to be G729 and this is working. I do have hardware that provides me 30 g729 licenses. I am setting each extensions to disallow=all and allow=g729. However when I have this setup, I get no voice mail prompts. I tried setting to disallow=all and allow=g729,alaw and I still have no audio when calling

Is anyone selling G729 License elsewhere other than Digium? Anyone allowed to sell a similar License as a reseller? -Kannaiyan

I have noticed that when I try to connect multiple G729 VoIP devices into a MeetMe conference that I can only add up to the number of G729 licenses I have. Now I would think that because all the devices are G729, this wouldn't be the case and the only license that would ever be used would be if a non G729 device or Zap channel was a part of the Meetme conference. This is apparently note the