similar to: patton smartnode 2400 with ic-t1v

Hello Does anyone have any experience with configuring BT (British Telecom) ISDN2e lines to work with Patton SmartNodes? I have a Patton SmartNode 4638, which is now connected to 3 x ISDN2e lines - and in turn connected to our internal LAN. I'm having huge issues configuring the SmartNode to successfully "see" the ISDN channels - and to be honest, I'm lost as to how to then

Hello Does anyone have any experience with configuring BT (British Telecom) ISDN2e lines to work with Patton SmartNodes - and then Asterisk? I have a Patton SmartNode 4638, which is now connected to 3 x ISDN2e lines - and in turn connected to our internal LAN. I'm having huge issues configuring the SmartNode to successfully "see" the ISDN channels - and to be honest, I'm

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

I have been given a Patton SmartNode 4114 and asked to get it working as POPS gateway for our asterisk box. The 4114 has 4 FXO ports. It's got firmware 3.21 on it. I currently have a single POPS line plugged into port 0. I can not seem to get the two to talk together. I am running asterisk 1.2.21.1. I am seeing the following repeatedly in * Jan 24 16:23:40 NOTICE[17063]: chan_sip.c:11291

Any have any success using a patton smartnode 4118/js/eiu fxs gateway with asterisk? We we're able to get the unit to register with asterisk, but when trying to place a call, no codec was compatible, even though I had all of the following enabled on the patton ... # G.711 A-Law/?-Law (64kbps) # G.726 (ADPCM 40, 32, 24, 16 kpbs) # G.723.1 (5.3 or 6.3 kbps) # G.729ab (8kbps) the link to this

Does anybody have any experience using a Patton SmartNode as a SIP/Telco gateway with Asterisk? They seem really inexpensive and appear to support all of the necessary features, but I don't have any experience with their products, so I don't know if they are any good. We are currently using a Cisco 2600 w/ PRI card and it works fine, but I was looking for someone else as a possible

Hi all We use pci/pci-e BRI cards in our installations. Due to echo problems (that was before Oslec and others), we quickly switched to cards with hardware-based EC. So we use exclusively Digium B410p cards that provide 64ms tail EC. For several reasons we'd like to switch to external BRI gateways like the Patton smartnodes (the price is getting really close to a B410p). I'm

Hi, we have and Asterisk server connected to a Patton Smartnode 4638 with 4 BRI. We configured 4 SIP account on Patton (1001, 1002, 1003, 1004). The system is fully functional, but we have a problem to recognize incoming calls from Asterisk: when a call come from SIP/1001 (BRI 1 on Patton) or SIP/1002 (BRI 2) or SIP/1003 (BRI 3) Asterisk record a call coming from SIP/1004. I have contacted Patton

Hi, How do you configure a Patton smartnode to register with an Asterisk server ? I could do it with 4.2 web server but I'm lots with 5.3 web interface ? Alternatively, has anyone a correct running-config for that ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I'm benchmarking the performance of a Patton Smartnode 411X gateway. My setup is : GSM phone <--PSTN--> SN411X <--SIP--> Asterisk <--SIP--> SIP phone My reference setup is: GSM phone <--PSTN--> analog phone In the first case, it takes roughly 10s from the moment GSM user hits Send button to the moment Asterisk gets the incoming call (or the SIP phone rings). In

Hi Can someone recommend a PRI to SIP Box that work well with asterisk We are presently testing with a Patton Smartnode 2400 but we are unable to fax through it. We don't want to use digium card in a linux box for the PRI connection. Which Cisco box would work. Thanks Patrick

We are testing the new T38 passthrough code (SVN-oej-t38passthrough-r13347): - we are using a Sipura SPA-2100 as the T.38 user device - we are using a Patton SmartNode 2400 as the T.38/PRI gateway - we are using Asterisk in the middle We have the following in the [general] section of our sip.conf: t38pt_udptl = yes t38pt_rtp = yes When a fax call comes in from the SmartNode to Asterisk

Hi! I have exactly the same problem on asterisk 1.8.22.0 and also on separate 11.2.1 when sending fax to PSTN. Tryed with spa-3102, spa-2102, Patton Smartnode 4634, and Zoiper softphone. SpanDsp also works without any problem on my box. As I remember it was a bug in 1.8.1.x that the a=T38MaxBitRate paramater was sent as "maxBitRate". Without capital "M". Are you closer to

Hi, I'm trying to configure a 4638 to pass inbound and outbound to and from ISDN and SIP interfaces. I'm using web interface at the moment. Setup is: ISDN -- <BRI> -- Patton 4638 -- <SIP> Asterisk -- <SIP> -- <IP Phone> I can call from IP phone but can't receive any incoming call : I can't see any SIP message coming in when a call comes in. Previously,

Hi, Changing the line bellow helped to get incoming calls but I add to remove secret= option in sip.conf (otherwise, Patton wouldn't respond to 407 Auth required challenges). If someone could enable secret and still get incoming calls (in any SmartWare 5.X), please, do not hesitate to share here ... interface sip IF-ASTERISK bind context sip-gateway ASTERISK route call dest-table

Hi all, I've been using telephone cards for 4-5 years and now I'm considering the Patton gateways. What are the pro and cons of Patton stuff compared to internal cards in a production system? Someone say external gateway are better because has no echo but have a longer delay when placing calls. Any suggestion appreciated. Thank you! Giorgio

I have a patton 1400 setup to handle the bri interface. As a trixbox user, I wanted a sip trunk rather than having to re-compile bri support into trixbix. Anyway, I have it working now so that asterisk can make calls and they are passed properly to the telephone network. Incoming calls however are another matter. I have (after turning on cli debug in the 1400) determined that its getting stuck

Hi, I succesfully install spandsp chan_misdn and digium card. the rxfax works fine and I get the fax result by email. I would like to do the same using a Patton gw + zaptel but I can't receive fax anymore, the call comes in from ISDN in the Patton gw, patton sends it to asterisk, asterisk run a macro to make a tif file using rxfax, the tif file is correctly created but with a 0 size the call

Hey Everyone, i am using Asterisk 1.4.21.1 with a old Patton SN1400 and some SNOM 300,320,360 Devices. In the combination with asterisk and the patton, there are occuring some strange behaviour, due to the calling and answering everything works good, clear voice, great availability. All the devices have to use ulaw, alaw and slinear is available but never the first choice since i use my

Hello all, i have a problem on incoming call's from SIP Provider that ist going through the Asterisk to a Grandstream HT502. The first ring is executed on the HT502 propperly, but no more ring will follow. But the call can nevertheless be answered by a phone on the gateway. If i call the same Gateway through a connected second Asterisk the ringing is done well. If a call is coming