similar to: Double Ringing for PRI Calls

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 This is slowly driving me nuts! I have several Cisco 7960s with SIP 8.2/7.5 fw connecting to Asterisk 1.2.5 driving a TE110P on a BT EuroISDN PRI line. On all outgoing calls I get a double ring tone (UK style + US style). I also have a DECT phone on a Sipura SPA-3000 configured with UK tones. This gives me a double ring of UK + UK, so this

Andrew, I don't think it's a Polycom issue. We took Asterisk out of the picture and had our Polycom phones communicate directly with an Audiocodes PSTN gateway. Unlike Asterisk, the audiocodes do not send 180 Ringing before sending 183 Session Progress, and the polycom's play the correct tones in this case. We WANT Asterisk to send progress tones in band. In our case it IS needed.

I have progressinband=yes in sip.conf, but Asterisk sends a 180-Ringing to my polycom phones and then it also sends 183-Session Progress. That doesn't seem to make sense. Shouldn't Asterisk NOT send 180-Ringing if progressinband=yes ? Doug.

Hello! I migrated asterisk 11 to 13 as user of FreePBX 12.0.76.2. As customer of German Telekom, I have three numbers and therefore three trunks - each number is bound to one trunk. After migration, some callers complained about missing ringback tone: they didn't hear any ring tone and where surprised that they suddenly got me anyway :-). The connection afterwards was as expected. Deeper

Hi all, using * 1.2.9.1 and this week all of the sudden calls keep ringing even after they've been picked up... Here's one users summary: When I pick up the phone, I hear a dial tone and I am able to dial out. But for some odd reason, the receiving line picks up while the outgoing line is still ringing. And the receiving line can hear everything while the phone is still ringing. I tested

I put a post on here about my issues with outbound calls not ringing but i haven't resolved it. so i am trying again. When i dial any outside number i dont get a ring tone at all. when the person picks up and starts to talk i can hear them fine. it sounds great. How do I start to troubleshot this? _________________________________________________________________ With Windows Live, you can

Hi, I have a Asterisk that connects to the PSTN via a PRI. After Asterisk sends the setup message it immediately sends a 183 Session Progress. Is there a way I can change it so that it sends a 100 Trying instead? Because I am having some issues with a equipment where it does not play a busy tone as a result of sending a 183 Session Progress then the 486 Busy. Thanks Remi

Any ideas on why callers who call into my customer's SIP trunk are not hearing a ringback tone? I had this on one other asterisk system, and wound up needing to set progressinband=yes in the SIP trunk config. I have set this on the current system & restarted asterisk, but to no avail. I am using: AsteriskNOW distro Asterisk build is 1.6 from AsteriskNOW repository:

I upgraded my Cisco7960 to SIP 8-2 from 7-4. Everything seems ok, works fine. Except that when I make an outbound call, I get a double-ring sound. I also found that if the target number is engaged, I get a ring sound and at the same time get a busy sound. If I revert back to 7-4, there is no problem. Anyone else had this, or any clues on how to fix it ? All of our other phones are still on

While I wait for the call to be answered I hear a "double ringing tone", like : expected tone : tuuu tuuu tuuu tuuu what I hear : tuuu tuuu tuuu tuuu tuuu tuuu tuuu tuuu the second "tuuu" I think is generated somewhere and not "true", since it sounds slightly different and the lambda between the first and the second is always

Whoops, email client auto-filled dev previously. Let's try this again. Michael Maier wrote: <snip> > Ok - but this doesn't seem to answer my main question: > > Why must > > progressinband=never > > be applied especially if asterisk uses it by default? The big difference > between w/ and w/o it is: The default in 13 is "no" which still

Hello, My target system is : PSTN <---> Sip Provider <---IP/ADSL---> Router with fw/NAT <--- SIP/IP/Eth --> Asterisk <--- SIP/IP/Eth --> SIP Phones Asterisk is configured to keep NAT connection with SIP provider open (with qualifyfreq) so I don't have any problem (yet) with either casual incoming or outgoing calls. To work around a possible No Audio when an incoming

Hello, We have an asterisk 1.2.13 box that use a Digium TE205P T1 PRI connect to the telco, users mainly use snom 320/300 SIP phones. When dialing to an external phone number with custom ringback music, users reported that they could not hear the music but can only hear the standard ring tone generated by the system. Is there any kind of settings need to allow the ringback music pass to the

When I make an outbound call I hear a half of a ring and than silence until the call opens up. It seems asterisk is sending a 183 after the 180 message. My CPE device does not support multiple 18x messages in the same call setup. When we receive the 180 we present ring back to the phone, but when we receive the 183 we get confused and stop the ring back tone, but do not open up the early media

I have a box (Genband) expecting the following: 100 trying 180 ringing with SDP Or 100 trying 183 with SDP And asterisk is sending: 100 trying 180 ringing 183 with SDP Any way to modify asterisk to send what he is expecting? Thanks, Dave -------------- next part -------------- An HTML attachment was scrubbed... URL:

I posted a problem earlier thinking it was due to a lack of sound card. Several members stated that you do not need a sound card to play audio to a PRI channel. I did some further testing and discovered that there is a problem with call progress tones or signaling on my PRI. I think that the reason I am not hearing audio from the MeetMe() or Playback() apps. is because the the calling side of

After reading a description of apparently the same problem by Juan J. Sierralta more detailed than mine "tuuu tuuu instead of tuuu" we've solved the problem changing the call progress tone of sip phones to something not udible.

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

Greetings folks. I seem to be having a problem where calls made from an IAX device (three single-line phones attached to IAXys) do not play the ring tone when calling out. There's a dial tone when I pick up the phone, and the call goes through just fine, it just doesn't ring. All my SIP phones ring normally, however. Is there an option I need to enable that I'm missing?

I have the following setup: AnalogPhone1--TDM400P-ASTERISK---via SIP---Softswitch--------POTS Phone2 When I call from AnalogPhone1 to Phone2 I hear a ringing tone and all is well. When making a call from Phone2, I get a dial tone but after dialing the number I hear nothing (no ringing tone). On Asterisk console it says that a call is coming in and that it is ringing Zap/2. I can also hear the