similar to: PRI echo issues: solvable?

I am trying to obtain optimum gain settings for a bank of analog lines connected to a channel bank. My telco has provided a 'Type 102' test line to use for incoming level calibration. This is functionally equivalent to app Milliwatt(), but provides tone from the CO inwards. Question is, how should one use this a 0dbm test source with ztmonitor? Am I correct in understanding that a 0dbm

Hey Guys! We had echo issue before so we replaced old PRI card with Sangoma A102D HWEC. Now my question is i set rx/txgain level 0.0 default do i need to touch this value or default is best. I have read on google and people say it should around 14844 on ztmonitor for rx/tx level same. I just use milliwatt and test my default 0.0 rx/tx level and it come around 4600. Do you think i need to make

Being one the many people trying to track down echo 'ghosts' I ran across this page: http://lists.digium.com/pipermail/asterisk-users/2004-November/071301.html suggesting ways to adjust the gain. I have a TDM400P 2x2 config with Kewlstart lines configured. I've located a local telco milliwatt test line, and when I call it, the gain numbers are no where near 14844. Now, this

Using TDM400's here and I have tried everything to cure the echo. I have used the Milliwatt test from the telco and from asterisk to tune RX/TX gain via a patched ztmonitor. What happens is I experience midcall echo. I turned on aggressive_suppressor and it seems to do great. The problem happens with misc. noise around the office will cause it to mute the other end of a phone call while

Hello! I'm having an echo problem with a TDM card. The TDM card is being fed by a channel bank just 12 or so feet away. When you put an analog handset on the line, both the RX and TX volume seem to be just fine. However, when I use the TDM card, I have to have an rxgain of 13.5, and even then, the audio is relatively quiet. I'm also getting echo on these lines, so I have turned

I came into this with my eyes wide open. I have read ABSOLUTELY EVERYTHING there is to be found on the net about avoiding echo problems BEFORE I even attempted to create a production system. Since lots of people are apparently using this in production environments now I just assumed that echo IS avoidable. As others have recommended, I created a test system with the proposed production

> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com]On Behalf Of Andrew > Kohlsmith > Sent: Thursday, September 29, 2005 2:23 PM > To: asterisk-users@lists.digium.com > Subject: Re: [Asterisk-Users] Best echo canceller? > > > On Thursday 29 September 2005 17:04, Claudio Canseco wrote: >

asterisk-users-bounces@lists.digium.com wrote: > In the following setup: > call coming from a pstn line -> into FXO card -> asterisk -> SIP > phone > > i get an incredible loud echo in the SIP phone (about 0,5-1s) > (everything i speak into SIP phone microphone i hear in its > speaker). The person calling from PSTN is not getting any echo. Make sure you're not

Hi, I've seen some reports about ruuning Intel modem with 537 or MD3200 chipset running with Zaptel drivers as a FXO port. Did anybody managed to set up a PCI faxmodem based on Intel536ep chipset to work with * and Zaptel drivers? Modem seemd to work just fine with Linux, but the driver says no;) some more info: Linux 2.4.26 mazuchna:~# cat /proc/pci | grep 536 Communication

Hi, I am having some issues with a new server install in Singapore. Outbound calls work fine. Inbound calls are not picked up by Asterisk. Zaptel 1.2.25 and Asterisk 1.2.28 both built from source. libpri installed wctdm and zaptel load without error Jun 6 23:34:03 fs01 kernel: [211138.372933] Zapata Telephony Interface Registered on major 196 Jun 6 23:34:03 fs01 kernel: [211138.372937]

This may be commonly known but I haven't come across it so here goes, maybe it'll help someone: I have terrible echo with asterisk 1.2, zaptel 1.2.12, and a TDM400P with 1 FXS and two FXO modules. The Mark2 echo canceller with Aggressive turned on was the only setting that would make it acceptable. I found fxotune with this zaptel version to be broken. I pulled the latest fxotune.c

Hi all, We have just installed a * server (CVS head) with a TE110P card and a IDSN20 line, we are using the GXP-2000 handsets running the latest firmware (.9). Some of the calls we are receiving have echo at the our end (we can hear ourselves speak). We have a traditional ISDN telephone system here as well and when I make a call from one of the handsets asterisk answers, directs the call to

Evening all. I'm looking at building an Asterisk system for one of the projects of the Charity where I'm the SysAdmin. The project has two analogue phone lines - BT Featureline Compact, we're in the UK - that I'd like Asterisk to handle. My current quandary is which FXO interface to use. I've been looking at the Digium TDM400P and Sangoma A200, which are similar prices for

Hello, Getting this error on dahdi_cfg. Reverting to 2.8 the error goes away: *line 15: Unable to create 'dahdi_cfg' mutex.* Is this a problem? Thanks in advance. Full detail: [ebox]> dahdi_cfg -vvvvvvv DAHDI Tools Version - 2.9.0.1 DAHDI Version: 2.9.0 Echo Canceller(s): HWEC Configuration ====================== SPAN 1: CCS/ AMI Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2:

I am currently running Asterisk 1.2.8, on an AMD Sempron 3100+ (ASUS K8N Nforce based board). I am using a Digium wctdm24xxp to terminate 8 (2x quad) FXO lines. Using ztmonitor (From zapata) I cannot see that there is any registerable incoming volume from these lines. I've been running them at rxgain = 25 (zapata.conf) to make the audio audible, however this creates poor call quality issues

hi! In your experience what is the best choice for echo canceller ? Which one should work better: STEVE, STEVE2, MARK, MARK2, MARK3, KB1 ? Regards, Claudio -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050929/f556bf91/attachment.htm

I'm having issues with echo. My setup is Polycom IP501 phones connected to an Adit 600 via T100P. 13 Lines going to the Adit. All echo so far is on the local side (Employees hears own voice, but only on some calls). Watching the channel with ztmonitor, I notice that TXGAIN is pegged out most of the time. RXGAIN is anywhere between 45 and 60%. Is it safe to assume that playing around

I have searched for how to locate echo cancelation on SIP clients, but cant find anything and echocancel=y doesnt seem to have any effect. Configuration: CVS-HEAD from last month iPAQ h5500 with SJPhone (gsm/ulaw/alaw) Problem description: When I place or receive a call I hear a faint delayed echo of myself. The other party hears a really bad nonmuted echo that makes the call unusable. Aside

Hello! Given the current discusison regarding ztmonitor, line testing, etc., I've been looking into purchasing a used transmission test set. From my research, it seems that there are two items that might fit the bill: the HP 3551A and the HP 4935A. I know nothing about these specific devices. I *do* have a good background in electronics, and I understand the concept what they're

I've spent the last week or so troubleshooting echo problems at my Wife's business, and I've been able to clear up about 99% of the echo, but there is still a little residual echo that I can't seem to "tweak out". The users describe it as "buzzing or crackling", but what it sounds like to me is a slight echo, but just of one syllable of the word.