similar to: No incoming calls from chan_capi 0.6

Hi, I tried to use the version 0.6 of chan_capi-cm for outgoing calls it works perfectly but for incoming calls it will not work: --- snip --- *CLI> capi debug CAPI Debugging Enabled -- CONNECT_IND (PLCI=0x101,DID=97,CID=0179903xxxx,CIP=0x1,CONTROLLER=0x1) == reventix: Incoming call '0179903xxxx' -> '97' -- reventix: info element CALLED PARTY NUMBER --

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

Hello, I am trying to configure asterisk 1.0.7pre to get incoming calls from an ISDN line using an AVM fritz PCI 2.0 with Chan_capi 0.3.5. My problem is that the context is not recognised in the /etc/asterisk/capi.conf I have in /etc/asterisk/capi.conf 's section "[interfaces]" the following directive context=isdn and the following directive in /etc/asterisk/extensions.conf in

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hi, I installed Asterisk with CAPI support. Everything works fine while starting Asterisk, but when a call comes in Asterisk hangsup the call after two times of ringing. The output is like: Jun 24 22:19:49 NOTICE[1082178480]: chan_capi.c:1931 capi_handle_msg: CONNECT_IND ID=002 #0x011d LEN=0048 Controller/PLCI/NCCI = 0x101 CIPValue = 0x10

Hi, I've a Fritz card which was working fine, recently I changed hardware and my nightmare started. Now when I call someone through the chan_capi (0.3.5 or 0.4.0) it works fine but when I receive calls I always get hungup. Can someone please give some help? Here are the logs: *CLI> -- CONNECT_IND ID=001 #0x0000 LEN=0049 Controller/PLCI/NCCI = 0x101 CIPValue

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

Hello List, because this is my first post to this list, i'd like to introduce myself. My name is Thorsten M?ller, 26 years old and live near Frankfurt/Main in germany. Okay, now to the reason for this posting: I just installed my first asterisk server (Debian 2.2 Kernel 2.4.18-686) with AVM ISDN Fritz PCI card (passive). I followed the configuration on http://voip-info.org and the

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hi, after I fixed my problem with the playback() application, I now have the next strange one. When I dial the number of our client, located in another town, I get a connection to the asterisk server, I can talk to my client or listen to his mailbox. If some in the town of this client calls him, he gets the ISDN error "service not available". Out office is connected to he office

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

Hi all, i have asterisk 1.0.9 with an Eicon Diva 4bri and chan_capi-cm-0.6. I have 2 NTBAs (one with did and one without). When using the one without did, i am able to place outgoing and incoming calls. When i use the NTBAs with did i have a layer 2 error. Anyone an idea? -- Executing Dial("SIP/2004-9634", "CAPI/g1/43XXXXXX") in new stack > data = g1/43XXXXXX

Hi! I'm here again with echo canceller problem... :-( I think I've done everything to enable echo canceller feature, but it still doesn't work... Can anybody tell me if there is some error or something missing in this configuration please? I'm using Eicon Diva Server 4Bri. http://www.eicon.com/worldwide/products/MediaGateways/disv4bri.htm?techspec=1&regID=4999 Card

Dear asterisk users! I want to control a hardware pbx with asterisk. What I need to do this is being able to press "hold" which can be done with capicommand(hold) and then send digits on a bri card which connects to my asterisk computer. So far I use Dial(CAPI/ISDN1/27:<<digits>>/bo,15) to do this. Are there better ways? Note that these are not dtmf, I'm afraid. I use

Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and

Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over ISDN/Capi but I don't succeed. My `capi.conf' is like show in many tutorial on the web. In `extensions.conf' I just added the following lines: [capi-in] exten =>

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

hi, I've been running a pure sip asterisk box for a while now with no problems, and i've recently added an isdn2e line from bt in the uk. everything is hooked up and i've got it ringing my sip extensions, but the logs don't quite look perfect and i can't see any description of what i should consider to be normal behaviour. would someone be able to look this over and tell me

Hi, i use chan_capi 0.3.1 with asterisk (stable branch cvs) and 3 x c4 active ISDN card. From Controller 1 - 7 there are no problems making calls between asterisk and the pstn. But when i make calls from controller 8 - 12 i get on every controller (8 - 12) a segmentation fault in asterisk :( I tried different linux distributions (gentoo 2004.1, redhat 9.0 , suse 9.1) but same error.

Hi, I'm using * with SIP in our LAN and CAPI for external phone calls. Everything works fine (SIP to SIP calls are ok and external incomming calls are ok too (CAPI to SIP)) exept the CAPI to SIP communication. When I try to make an external call from a SIP client, the (ext) phone rings (while the SIP client display "trying...") but when I hangup I don't get any communication and