similar to: How to IGNORE distinctive ring

Hi All, I was wondering what the status of distinctive ring support in Asterisk is? I had a google search & read and Mark Spencer wrote some support for it. Is distinctive ring different in every country or is it pretty standard? And for my final question, does the Wildcard FXO card support distinctive ring? Essentially what I'm trying to do is route incoming calls with ring #1 to,

I'm looking to give the SPA-3000 a whirl as I'm having too much difficulty with the irq sharing thing inside the box. I'm reading the book but without having one in-hand to play with it appears a little obtuse at this time. Before I drop down my money can someone with some hands-on with one of these confirm if the SPA-3000 can: a) detect inbound distinctive ring (this looks to me like

Hello - I have a TDM400P with 2 FXO and 2 FXS modules. Feeding the FXS modules are two VOIP lines which are terminated by VOIP adapters and have regular RJ11 wires connecting to the FXS ports. Since the two different VOIP lines have different phone numbers, and I know and can tell asterisk which VOIP line is connected to which FXS port, can I cause a distinctive ring on the extensions if a call

Hi All, I've recently got a "second" number installed on my PSTN line, trusting the Asterisk distinctive ring detection would work as expected. It appeared to work fine at the start, as the second number generated a different ring pattern to 0,0,0 (in the console) only to realise that almost every phone call to this "second" number generated a different ring pattern.

I have a line from BT (UK) connected to my asterisk system, on a TDM400P. I am able to see either distinctive ring cadences or caller ID but not both. If I try to enable both, all drings show up as 0,0,0. This is a pain because, if I make a call out over that line and the number I call is busy, I can elect to camp on it (ringback), which results in a different cadence of ring when the called

I am somewhat unsure as to the definition of "Distinctive Ring". What I am trying to achieve is to have Zap connected phones (TDM400P) ring with different cadences depending on whether the call is incoming on the PSTN context or an IAX2 context. Googling, I find this from Mark: I've added distinctive ring support to Asterisk now (also I've added answer confirmation which is

I am trying to get distinctive ring to work on my PSTN with no luck. I can get 2 different ring codes but it skips the context assigned... here is my complete zapata.conf: [channels] signalling=fxs_ks usecallerid=yes rxgain=1.0 txgain=1.0 language=en context=default usedistinctiveringdetection=yes dring1=134,0,0 dring2=137,0,0 dring1context=internal2 dring2context=default

I have been looking into how to setup distinctive ringing on a SPA-2100. So far the only thing i have been able to find is how to define a distinctive ring in the spa config. What i cannot figure out is what SIP message i need to be sending to it in order for it use the ring. I did find out how to add the sip message for distinctive ring i just dont know what variable needs to be passed in order

Does anyone know how to set the distinctive ring on the Linksys SPA941? I want to be able to dial one extension and have the phone ring with a certain tone and then dial another and have the phone ring with a different tone. I have tried the following ------------------------------------------------------------------- exten => 802,1,SIPAddHeader(call_info=Classic-4) exten =>

Hi Can anyone with distinctive ring on their 7960's possibly post how they've got it to work? I understand that the ALERT_INFO variable is involved but using the examples for the variable value from the WiKi I'm just getting an error message from the Asterisk concole. Thanks in advance. P

Hi Everyone, Using Elastix (FreePBX + Asterisk 1.4.2x combination) with Aastra phones, how can one receive distinctive ring tones for INTERNAL calls ONLY? Even though FreePBX Inbound has an option for Alert_INFO but that doesn't work when the call comes into an IVR or Queue. The calls has to go directly to extension for external ringtone to be different. So, I am looking for internal calls

I am looking for clues on how to configure distinctive ring for a PolyCom SoundPoint 300. Does ALERT_INFO apply? If so, how? Thanks, David Koski david.nospham@kosmosisland.com

Hello all! We have a PSTN line with four numbers calling into it. There is distinctive ring on these lines. They are are follows: 1. standard ring 2. short ring 3. long ring 4. short ring, long ring, short ring Based on the information I have been able to find, I have created the following entries in my zapata.conf file, to try and weed out some of the timings: dring1=95,0,0

I'm using Asterisk 1.4.5 (will try 1.4.6 on Thursday, but I don't see anything in the changelog after the 1.4.5 release dealing with distinctive ring), zaptel 1.4.3, and wanpipe 2.3.4-10 with a Sangoma A200 card. I enabled usedistinctiveringdetection in zapata.conf. However, on the Asterisk console, the output I get is: -- Detected ring pattern: 0,0,0 It would appear that Asterisk is

Hi All... Is it possible to cause asterisk to answer some distinctive ring patterns but not others? I have a POTS line plugged into an X100P and I would like * to ignore one ring cadence that is answered by a fax machine. How would I do that? Thanks...

Hello List I have searched the lists, the wiki and the handbook and see how to use distinctive ring inside however I can't find incoming. I have 1 x100p and 2 phone numbers, My Voice calls are normal ring, my Fax are short short long. How do I tell * to route the call to an extension based on the ring candance? Is it possible? Right now it seems when the x100p sees the short short long it

Does anyone know of a way to setup distinctive ring in * for a Grandstream BT 101? I'm attempting to setup a way for users to distinguish between external and internal calls. I've tried ALERT_INFO with no success. Thanks, Mason Herring Director of Engineering Delta Signal, LLC -------------- next part -------------- An HTML attachment was scrubbed... URL:

I've done the unspeakable. I took a working setup of 1.0.5 and upgraded with the latest cvs. with 1.0.5 distinctive ring worked great. with the latest cvs, it doesn't seem to work with my sipura 2000 (the only thing i have to test it with). I can see in console that its sending the info, but its not working? i realize the likely hood is I messed something up somehow during checkout or

Is it possible to allow distinctive rings work for FXS ports as well? I need a certain FXS extension to ring a distinctive double ring. I modified zapata.conf appropriately for dring1,dring2 and it just Seems to ignore my updates. Do distinctive rings only work for FXO ports? Paul Seniuk -------------- next part -------------- A non-text attachment was scrubbed... Name: Paul Seniuk.vcf

Greetings, I am trying to implement distinctive ringing on a Cisco 7960. I have tried setting alert_info to chirp1 or chirp2 before dialing the phone, but it has no affect. If you have successfully implemented distinctive ringing on a 7960, I would really appreciate seeing the snipit of code that works. Thanks in advance Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775)