similar to: Cisco AS5400 Configuration as a SIP Peer - URGENT

i want to use Cisco AS5400 media Gateway as my PSTN Gateway instead of using the E1 PCI cards in asterisk box ,is this practically possible? can i use SIP in the connection between Asterisk and Cisco AS 5400 Gateway? _________________________________________________________________ Express yourself instantly with MSN Messenger! Download today it's FREE!

Hi, Would just like to inquire if anyone here has a setup of asterisk to send traffic to AS5400 connected to an SS7-PRI.? this is more of a AS54 question, as i've been reading and i always stumble upon PGW2200 as a requirement to handle SS7 signaling on the AS54. Has anyone able to send calls from asterisk to an as 54 with SS7-PRI without PGW2200? TIA Regards, Nhadie --------------

I have the following setup: DS3 -> Cisco AS5400 -> H.323 (ooh323) -> Asterisk Inbound calls work great but outbound calls fail. So to check and make sure we have outbound calling ability on the DS3 we setup a Cisco Call Manager Express and it can make outbound calls both local and long distance with no problems. The failure code is Cause i = 0x8381 - Unallocated/unassigned number. We

Hi, this is the second time that i post this, may be a wasnt clear the first time. Im having problems with an incoming peer after i upgraded asterisk from 1.0 to 1.2.4, in 1.0 i used to configure the incoming peers like this: register => @prepago-in [prepago-in] type=friend host=192.168.10.102 ; this is the cisco's ip context = from-external dtmfmode=rfc2833 insecure=very ; required for

I see a lot of comments but no actual show runs. Can someone post a 7206 config. I am having a dickens of a time getting calls to pass. I currently have the following loaded. Cisco IOS Software, 7200 Software (C7200-IK9O3S-M), Version 12.3(8)T6, RELEASE SOFTWARE (fc2) Thanks !!! Jerry -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.344 /

We've got this configuration : Cisco as5400 --- asterisk main server ---- asterisk for cells ---- gsm gateway cisco and the gsm gateway are connected to asterisk via sip, the two asterisk servers are connected via iax. On a succesful call the cisco (not always, 60% of the times) will keep sending a ringtone to the connected phone, even if the call is answered, actually if the user behind

I am up to post 5 on my step-by-step but I hit a bit of a snag and so far my searches have failed me, I hope someone can help. (By the way, I added an asterisk index for quick navigation on the blog http://qvlweb.blogspot.com/2009/04/asterisk-pbx-install-index.html.) Here is the snag and I am hoping for a little help from the collective. Inbound I have 2 different numbers. I can call in on both

Hello, I heard that since asterisk 1.6.0.6, now you can send faxes with t.38 through asterisk to a PST gateway that supports t.38 too. Is that true ? If so, what elements you need to make it work beside asterisk and the PSTN trunk ? Thanks all.- -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm trying to get Asterisk to pass thru calls using the G729 codec. I've got a 7960 phone and my gateway is an AS5400. I got the following messages when debugging SIP (7778881000 is the 7960): WARNING[1872]: channel.c:2115 ast_channel_make_compatible: No path to translate from SIP/7778881000-2874(4) to SIP/as5400-35c1(256) WARNING[1872]: app_dial.c:1002 dial_exec: Had to drop call

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

We're having an issue with connecting a Cisco ITS installation to * such that DTMF tones are passed to *. DTMF tones aren't passed to voicemail or to any of the interfaces behind *. On the Cisco Side: dial-peer voice 8 voip destination-pattern 9999$ session protocol sipv2 session target ipv4:172.16.1.249 session transport udp dtmf-relay rtp-nte codec g711ulaw no vad We have also

I wouldn't expect you to be using RFC3389 if your using A-law, can you include your IOS version and IOS config file ... I have not specified any allow's or disallow's in my * config for the codecs with my 5300, I also use Cisco 79xx phones and I use the option within the phones config file to select the preffered codec and when I change this to G.729/A-law/U-law all works perfectly

Hello, We have a sip trunk end point with cisco media gateway. VoIP works fine. But when we try to send faxes thru this trunk, we simply can not. Is there anybody experienced such problem and solved? How should i set sip.conf and udptl.conf. I already have t38pt_udptl=yes in sip.conf Thank you.

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

I'm stuck running a old copy of asterisk because something strange is going on in later versions of the CVS.. When I call in from a PSTN into my cisco 2610XM gateway which then routes the call to my asterisk box via sip.. Asterisk can no longer process DTMF tones generated by the calling party. This affects DISA, prompts and menus.. Has anyone else had this problem?? and use.. I DO have

Ok here is a question that has gotten me stumped. I have an Asterisk system up and running. I need to connect it via the Internet to a Sip Cisco system. This is what they have. I have there IP address's and login. X-lite is able to connect to them and make a call! So I have the name right! CISCO router model: 2621 VoIP module: NM-HDA-4FXS I have done Google lookup and at the Wiki about

Topology: PSTN<-T1 PRI->NEAX2400<-T1 PRI->Cisco 3825<-Ethernet-> Asterisk VoIP server When I make a call to a VoIP user from the PSTN, the call gets routed through the PBX, and Cisco. Because of that the DTMF tones are passed inband, which I can hear on the VoIP end of the call. However, I have one extension on asterisk set up so that I can check voice mail when away from my

Hello all, When I generate an out-going call from *, the DTMF detection is not working ? ASTERISK --> GW AS5300 --> PSTN But the DTMF is working correctly when it's an incoming call. PSTN - -> GW AS5300 - -> ASTERISK Well, I tried with the 3 dtmfmode of asterisk inband, rfc2833 and info, no way !!! Is it normal that asterisk try to setup the outgoing-call using ULAW ? if I

I have gotten this sort of problem some weeks ago and have solved it with the mailing list archive. But now I have this problem again with the class library. What should I put in library/class/R/zzz.R? Everything I put in that file leads to the same error message. I'm running 0.61.3 on Linux. > knn1(train, test, cl) Error in .C("VR_knn1", as.integer(ntr), as.integer(nte),

Hi. If I use a Cisco as a PSTN termination GW and need to route all incoming isdn calls to my asterisk and all outgoing calls from asterisk via the cisco out to pstn, how do I do that ? in the cisco I have this: dial-peer voice 1 pots destination-pattern [0-9]T no digit-strip direct-inward-dial port 3/0:D ! dial-peer voice 50 voip destination-pattern [0-9] voice-class codec 1 session