similar to: Problems with TE205P

Hi all, I've setup a PBX in production environment last week but we have immediatly find out drop conversations and lot of errors (in asterisk logs) like: Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 My configuration is: Motherboard: SuperMicro P8SCT (Intel E7221 chipset) Hypertrading and APIC enabled CPU: P4 3GHz Digium TE205P

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs

Hi there, Running patlooptest following instructions on Digium KB, using dahdi 2.5.1 with a TE205P. I'm getting this kind of output (not full output). Note, I'm using a standard cat5 ethernet cable (30cm), with a Digium T10i crossover. Error 4985 (loop 19898, offset 425, error 214): Unexpected result, Read: 0xff, Expected 0x00. Offset 422 { ff ff ff ff ff ff ff } Error 4986 (loop

I am having a problem with asterisk not being stable enough for production use. I have two cards, the digium TE406P, and the TE410P. The TE410P is the primary card that I am using but I would like to move to the TE406P for the echo cancellation and more flexibility of PCI slots available. General config info: 3 PRIs, configured as such: span=1,2,0,esf,b8zs span=2,0,0,esf,b8zs

Trying to find my feet here. If I wanted to connect Asterisk to a PRI and throw in a T1 Adtran channel bank into the mix for fax machines would the following work? Connect PRI line from telco to Port 1 on the Digium Wildcard TE205P. Connect Adtran TA-624-T1 to Post 2 on the Digium Wildcard TE205P also, would I need a crossover to the channelbank or is it a patch lead like the connection to the

Hi, I am having problems with an Asterisk with a Digium TE205P card. The issue is that the Ring Back Tone is noisy. I am making modem's calls and this noise influences on the initial negotiation protocol, so modems have to recall. My configuration is: Asterisk version: Asterisk 1.4.21.2 Linux version: CentOS release 5.2 (Final) Card: Digium TE205P

Hi ..., I've a TE205P card installed in my asterisk box.Port 1 of my card is connected to service provider.From port 2 I want to connect Avay Partner system. what type of cable I require to connect the partner system (straight/cross over). How the call routing from outside will be done to epbx. Thanks inadvance regards rudra -------------- next part -------------- An HTML attachment

Hi guys, Currently I just purchased the TE205P for the installation of my ISDN30 setup. I compiled, setup the card correctly I think. When I do the ztcfg -vvv it shows all 31 channels clear, with 30 bchannels using for voice ranging from 1-15, 17-31, and 16 is the dchannel. However, when I do a cat /proc/zaptel/1 I see only 24 channels configured, and then, when I do a cat /proc/zaptel/2 I see

I have a TE205P, jumpered for E1, added the missing wct4xxp-line to /etc/modprobe.d/zaptel, zaptel.conf is just span=1,1,0,ccs,hdb3,crc4,yellow span=2,2,0,ccs,hdb3,crc4,yellow bchan=1-15 dchan=16 bchan=17-31 bchan=32-46 dchan=47 bchan=48-62 Which, according to my reading of the documentation I could find, should be correct. ztcfg doesn't complain about anything, yet all I ever get is RED

Hello, I am working on a project and have a few questions. I want to connect one port of the TE205p to the PSTN, and another port to the PRI port of a PBX. Basically Asterisk will sit between the PSTN and the existing PBX. Are there any gotcha's I need to be aware of? Will the existing PBX be able to dial through asterisk as if it was a PSTN connection? -- Isaac McDonald Got VoIP? imcdona

Hi there, We've got a problem connecting Asterisk with a TE205P to a TeleWest E1 ISDN line in the UK. We get a lot of "HDLC Bad FCS (8) on Primary D-channel" errors, and every so often the Primary D-channel goes down and all the calls got dropped. We've fully tested the card and made sure it's got its own IRQ. I was just wondering if anyone out there has

Hi i have a PRI connected to a TE205P. Actually, can i send and receive FAX through Asterisk using stable solutions? Or shall i connect an ATA to Asterisk and then a modem with Hylafax? -- /*************/ nik600 https://sourceforge.net/projects/ccmanager https://sourceforge.net/projects/nikstresser

I have had a tough time finding a good stable combination of motherboard with either a TE410P or TE406P and would like to solicit input for suggestions. Currently, we are utilizing the Supermicro P8SCT. I have disabled the onboard NIC cards and I am currently using a separate 3COM PCI card. I have tried both cards in this board with mixed results. This is the third motherboard we have used and

hi after some testing with A@H, i've decided to install my asterisk server on a slackware (because it's my favourite distro and it is still suggested here http://www.voip-info.org/wiki-Asterisk+Linux+Slackware) , so, i've installed the last 10.2 release, and i've recompiled the 2.6.15.4 kernel. then i've downloaded asterisk1.2.4 and zaptel1.2.4 i load module zaptel and

Hey folks, I have a Digium TE205P working as a man in the middle: PRI line -------- Asterisk/TE205P -------- PBX The PBX is a Panasonic KX - TVP 100. Everything is working great except for one little issue. Asterisk isn't hanging up the PRI B channel when the PBX channel is hung up. I don't want to overload you with information but please ask if more is needed. I suspect I'm

hi i'm trying to configure a TE205P on asterisk@home i've edited /etc/sysconfig/zaptel adding this line: MODULES="$MODULES wct2xxp" now, when the system is loading, i can see that the wct2xxp module is loaded correctly but if i try the command: /usr/local/sbin/genzaptelconf i get: STOPPING ASTERISK STOPPING FOP SERVER Generating '/etc/zaptel.conf' Generating

Does anyone know if patlooptest either doesn't work for fxo/fxs signaled channels or if you have to do it a different way? If I run ./patlooptest /dev/zap/25 60 with a config like: fxsks=25-32 fxoks=33-48 it gives me a bunch of output along the lines of: (Error 4071): Unexpected result, 254 != 255, 11 bytes since last error. (Error 4072): Unexpected result, 0 != 255, 1 bytes since last

Hi List. I'm running the patlooptest program I've found in dahdi_tools 2.1.0.2. The target is a TE121P board with a loopback cable inserted on the socket. I suppose that the loopback is working fine because I'm able to see the green led on and dahdi_tool reports no errors. When I run the patlooptest I've a lot of errors (the received values are completely different than the

I am having trouble with zttest on a Tyan board, dual AMD Opteron's on FC3. Tried different kernels, no IRQ sharing, everything looks in order. My zaptel modules load fine, but if I run zttest, it just hangs. Below is the strace output and you can see where it stops. Anyone have any ideas? [root@asterisktest zaptel]# strace ./zttest execve("./zttest", ["./zttest"],