similar to: Using E1 without power off simence pbx

hello list, i need to setup an asterisk system with 5 ISDN trunks. i found C4 cards but they are very expensive. i found that if i use 5 AVM Fritz! cards it would be very cheap. i want to use 2 boxes. 3 in boxA +2 in boxB =5 isdn. and i want, this two boxs to work as a single box so that one box can share ISDN hardware from other box. this system will be serving a call center. currenly we are

Hey folks, I have a Digium TE205P working as a man in the middle: PRI line -------- Asterisk/TE205P -------- PBX The PBX is a Panasonic KX - TVP 100. Everything is working great except for one little issue. Asterisk isn't hanging up the PRI B channel when the PBX channel is hung up. I don't want to overload you with information but please ask if more is needed. I suspect I'm

Hi all, I have an existing panasonic analog pbx in use and a asterisk server with digium tdm400p(2 fxs and 2 fxo). channel 1 -> fxs -> telephone channel 2 -> fxs -> telephone channel 3 -> fxo -> extension 15 at panasonic pbx channel 4 -> fxo -> phone line from telco We call in to fxo (channel 4) and enter the ivr which prompt us to enter the extension number. After

Hello, I just setup the Asterisk to integrate with Panasonic legacy PBX. Config as followings, PSTN <-- PanasonicPBX--TDM400P(FXO)--AsteriskPC --> Internet * is for AA / Voicemail and VOIP in/out Currently the AA / Voicemail function for incoming PSTN calls are working well. My problem is for the incoming VOIP call. It can ring my internal extensions and talk without problem. But

> Date: Thu, 23 Jun 2005 08:50:50 +0200 > From: "Robert Rozman" <rozman@fri.uni-lj.si> > Subject: [Asterisk-Users] Loosing hair on connecting Panasonic PBX- * > - Euroisdn Italy > > I'm pulling my hair down and getting bold :-) ..... I have Asterisk between > Panasonic KXTD816 and Euroisdn in Italy (beronet octobri and bristuff > Asterisk).... Plenty of

I'd like to have my Asterisk system pick up a certain extension on an existing Panasonic PBX when it rings. (It's connected to some proprietary Panasonic doorphones that I haven't replaced yet.) I connected that extension to an FXO port on a Digium AEX410 card, and set that channel to have the context "doorphone". The problem is that the extension is never executed. With

Hello - Warning: newbie questions at 12 o'clock! I am looking at transitioning my house from a Panasonic KXT1232 to an asterisk-based PBX (*PBX). We currently have 5 CO lines and 16 extensions plus ADSL with a static IP. I have looked at the various docs, but find I still have some questions. 1. Interface cards a. Should I buy a T100P + channel bank? (BTW: Why isn't this

Dear Harry, Thx for the explanation. My team manage building's PBX that use Asterisk 13.x. We use Asterisk PBX for this buildings that have apartment and office customer. >From my Asterisk PBX, we connect to IPPhone (yealink) or ATA Converter (cisco SPA112). Others are using PBX like panasonic analog, audiocodes SBC, etc, and we use ATA Converter to convert from SIP to Analog (CO Line)

Hi, Is there anyone here who has experience connecting Asterisk (ver 13.8) with PBX Panasonic KX-TDA600 ? The architecture more less like this : Telco Sip Trunk ---> Asterisk 13 ---> Panasonic KX-TDA600 ---> Phone / Fax Thanks in advance, Regards, Ikka - Jakarta, Indonesia -------------- next part -------------- An HTML attachment was scrubbed... URL:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello everyone, I've got an old AVM all-in-one ISDN box lying around. Currently, it's attached to my server via USB and CAPI4Linux and additionally has an analog DECT phone attached to one of its TAE ports. As I'm planning to switch to VOIP via cable internet, I'm now thinking about the following setup: [Internet] -> Cablemodem

Hi, I'm pulling my hair down and getting bold :-) ..... I have Asterisk between Panasonic KXTD816 and Euroisdn in Italy (beronet octobri and bristuff Asterisk).... I'm trying to do just plain transfer of call from pbx to ISDN through Asterisk... It seems like PBX hangsup, when call is progressing with no apparent reason. I'd kindly ask for any advice or some working example for

Hi. I've searched the archives and found nothing regarding collaborating Asterisk with a Panasonic PBX (TD1232 to be exact) Here's my question: Can I use a Wildcard X100P to connect an outgoing line jack (on the Panasonic) to Asterisk, so I can route calls from the PBX to Asterisk, and calls from Asterisk to the PBX? On the hardware page for the X100P card is says it's great for

Hi all, There is someone with some experience interconnecting a Panasonic digital PBX (KX-TD1232) with Asterisk? Thank you and best regards, Dan

Hi, at the university department we have quite old Panasonic 2+6 PBX (1BRI + 6 POTS for outputs) and 25 local analog extensions. We would like to add Asterisk with 1 fresh BRI line and possibly integrate with existing equipment (we would like to crossover between both pbxses). What would be most efficient way to do this ? Thanks in advance, regards, Rob.

Hello list. I'm going te explain my trouble. I have my asterisk with a TDM400P with 4 FXS channels. Two ports are connected to a Panasonic PBX (it's working fine), and others two ports are connected to an Alcatel 4200 PBX (but it doesn't anwer). I connected to a CO port (where i had a pstn line). When I call to the Alcatel PBX, the asterisk show me in it console that es ringing but

Panasonic PBX KX-TDA600 it doesn't support SIP protocol for VoIP technology it only support H323 Trunk through 4 or 16 channels gateway card and TDM technology with ISDN BRI and PRI card. Mc GRATH Ricardo

Hi All, I got a doubt about something I want to do with asterisk. I have this office (site a) with only a Panasonic analog PBX and another office (site b) with an Asterisk Box with an ADIT 600 . I want to interconnect both via IAX. Is it possible to put a new asterisk box in site a without the channel bank and put a card (FXS or FXO???) and connect it to the pbx as a CO line ? What

Good day, anyone out there running an ISDN pbx behind an Asterisk server with an AVM active card? At this moment Asterisk is connected to the internal ISDN bus of the PBX, but I want to control the calls coming in from the outside, before sending them of to the PBX. Any BTDT is greatly appreciated. rgds pos

The place I currently work at has a Panasonic Key system with 9 extensions, and no voicemail. It services 2 PSTN lines. I am hoping to use Asterisk to host voicemail (I would like to use the IVR also, but I don't even know if or how it would work). Do I need to use a PRI between the two, or is there a simple solution? I would like people to be able to answer the phone and

Hi guys, How's things going ? Got a bit of a weird one here that I've been unable to solve. I have a Panasonic PBX linked to a Sirrix Quad BRI card that is running in TE (ptp) mode in a Asterisk box - this then links through Internet to another Asterisk box via IAX2. When a user on the Panasonic PBX system dials the extension of my Sirrix Asterisk box, Asterisk answers and says