similar to: Loop back cable pinout 15 Pin Serial

Say I had a crossover cable that connected a Mitel SX200 to a TE110P and the pinout was done as such: 1 - 4 2 - 5 5 - 1 4 - 2 (the 5 and 4 are transposed on the left side) Instead of the proper way of: 1 - 4 2 - 5 4 - 1 5 - 2 What would the results be? We have had the former as our cabling for a few months and the connection has been fine. Slip errors here and there. But we have had major

Hi there! I just recently got a nice new UPS to power most of my computer equipment, and having it working perfectly under NUT. However, I had a perfectly good Powercom Black Night 600AP UPS, which I'm now trying to get to power my internet gateway. Unfortuantly, due to not thinking on my part, I threw away the original serial cable. I have tried a straight - through cable, and the one

Hi, I have a Cisco 7960G phone for which I know the pinout of the headset socket. I have a couple of standard telephone headsets which I do not know the pinout of. I'd like to connect the two. If I have the pinout of a normal/standard headset I can rewire the ones I have to match the cisco. Thanks Mike

> Many thanks Julian. Are you looking for the pinout for a single plug 2.5mm (cellphone) headset or a dual plug 3.5mm (computer) headset? -- Nabeel Jafferali Tel: +1 (416) 628-9342 Toronto +1 (646) 225-7426 New York FWD: 46990 Email/MSN: nabeel<at>jafferali.net

I have a Cisco 7960 phone. I cannot seem to use the settings button to get into the phone to change the TFTP server. I've set up a DHCP Server, TFTP Server with the same address, and the phone requests the address of 0.0.0.0, the server offers the address of 192.168.2.2, but the phone seems not to take it. I have no action on the TFTP side. So, since I can't seem to server the phone

Hi, Ok, I put the new TE410 into our system last night - This is the second TE410P card. There is also TDM400P in Slot 5 with IRQ 9 which is shared with aic7xxx (SCSI) According to "cat /proc/interrupts", the new card is in the second slot using IRQ 11 (the first card is in slot 1 on IRQ 10 - but always has been). With only the original card install, there has been no issues with

Hello all, I have obtained a Compaq T700 H UPS sans-cable. My research indicates it would've come with a HP #201092-001 cable, and from previous posts on this list, it speaks upscode2, possibly being a rebadged Eaton unit. Any suggestions for cable pinouts I can try? Regards, Mathew McBride

Hi Asterisk Community, I have a development with a TDM11B in it. I am trying to connect this to a exchange line as well as a UK telephone and are looking for some pinout information for the FXS port. Is it the centre 2 pins that at the tip and ring. I have been digging around the Digium site but cannot seem to pick up this info. Any help appreciated. Thanks -- Gary

We have recently started routing about 3 PRI's worth of traffic thru our asterisk box. The text on the console now flys by so damn fast, I can't really see what the heck is going on. Even with verbosity 0 and debug 0 it is still so fast. Is there some way I can attach to the console in a way that will allow me to grep or otherwise filter the text so I can focus on something in

brett@websmyths.com wrote: > Also - an outside chance - make sure Tip and Ring > are correct. You could be getting ground loops - depends on the noise. > I am having noise and slip errors between my TE110P and a legacy PBX T1 card. Could this be the same symptom? The connection is made using a 15 pin serial on the T1 Card side to RJ48 on the TE110P side. I can't determine what the

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi, Digium's E400P has RJ45 conector and my E1 link has BNC concetor. Could someone tell me the cable pinouts to make this conection? thanks Eduardo

Hi I'm looking for a pinout for the above. Note this has what i'd call RJ45 sockets (or someone smart can correct me). I need to plug into BT (rj13?). And, yes I've googled (glad I'm not chinese) and have tried the suggested, just plug in a 6 connector rj11 and i didnt work atall. On a side note, I cannot beleive that Digium dont have this information on there site, it

Hi, I just got a T1 interface for a AT&T (became Lucent) System75 (uses same cards as Definity). I would take a crack at making a cable but can't determine the pinout for a cable and it is not apparent from the board. Asking you guys makes sense as one of you may have one of these systems. The cable has a amphenol male D50 connector on one end and probably a rj45 on the other. I also

I've just acquired a Unitek ALPHA 1200 Sx UPS to replace an older serial UPS that's been working well with NUT for years. Could anyone with a Unitek tell me what the pinout on the 10P10C plug is so I can make up a cable? Thanks.

First, a little history; nut has been working on this system for about two years. It was a Fedora Core 2 (3?) system that I wiped and installed SUSE 10.1 on so I'm fairly confident of the hardware. I thought I'd saved the nut configuration details before I did the reinstall, but can't find them. (D'oh!) The UPS is an APC BackUPS Pro 420. The cable is a clone of the APC

Hi guys, just to let u known the pinout for the adapter : Adapter for connect the E1 telco lines on my digium card DB9 RJ45 3 1 8 2 2 4 6 5 Adapter used for connect the Hicom150 traditional PBX on my digium card (cross connection) DB9 RJ45 3 4 8 5 2 1

I for one think it is a great idea to buy a book with hard earned money and wait a few days to a week just to get an answer to a question that is freely available on the internet immediately. Hard pressed to think of anything in the "book" that is not on with wiki with more up to date and useful information. -----Original Message----- From: Alexander Lopez

hello I have an asterisk server with a te110p E1 digium card. the server is a hp ML370 3,2 Ghz 64bits, 1Mo L2 , 1Go Ram, 3 SCSI 73Go in raid5. I want to use in the same machine the kannel SMSC. i have no big trafic in the two gateway but I want to know if it generate a performence problem for asterisk I use fedora core4 with latest asterisk version . thanks Regards issam -------------- next part

I have trouble in getting communication work with MGE Ellipse 500. I bought it second hand and I don't have the cable for it. How do I know if it's the Serial or USB model? The serial number of the unit is: 769B16015. I suspect it is the serial version as the label next to the RJ11 stands "com port", but I can't be 100% sure. MGE Ellipse serial cable pinout can be found