similar to: Ring more than two isdn phones simultaneously

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

Hi, I would like to implement a inexpensive home PBX with Asterisk. I have an internal ISDN bus with 6 ISDN phones. I now thought, I connect a Fritz card to my Mehrgerateanschluss (Point-to-Multipoint) supplied by my provider and a second Fritz card to the internal bus. Will this work? Thanks for the help, Arik

Hi, is anybody running asterisk on a xen domU and can give an opinion on the following: I have delegated a FritzCard and a HFC card to my domU and installed an asterisk setup that was running on the same isdn hardware but on a dedicated machine flawlessly. I experienced what I believed to be timing problems: sometimes calls on the Fritzcard did not seem to "reach" asterisk, when

Hi, I have following problems compiling bristuff-0.2.0RC8m. Has anybody seen them before and can point me in the right direction? zaphfc/make all: ---------------------- /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c: In function 'hfc_findCards': /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c:1000: error: invalid lvalue in assignment make[2]: *** [

Hi, I am looking for inexpensive isdn card that supports nt mode with asterisk. Does it mean that if mISDN has nt mode support for a specific card that asterisk has too? If yes, I presume I could buy any of the cards listed on the PBX4Linux page: http://isdn.jolly.de/cards.html Or will asterisk work ONLY with cards with hfc chipsets? Cheers, Arik

Hi, I have a Fedora 7 xen system with a domU to which I have delegated via pciback two isdn pci cards. One is a HFC-S card, the other a AVM Fritz!Card Pci 2.0. In the domU I load mISDN drivers for the cards. The two cards are recognized and function well UNTIL I either decide to unload one or both of the card driver modules (hfcpci and avmfritz) or I decide to shut down the domU. At this

Hi all, I'm new to the forum. Oh no....newbie question coming, I hear you all cry! I'm playing around with Asterisk@home and have installed software and fiddled around with sip and extensions files. I have manage to make out going calls through Sipgate using X-Lite but cannot for some reason receive incoming calls. Incoming calls do not even show up on the switchboard panel. I've

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello together, I am setting up a communication server which should also act a very-low-load PSTN gateway. I am usiing a AMD K6 200 running from a 500 MB usb memory stick. What is the ABSOLUTE minimum space requirements for ~ running asterisk to work as gateway between isdn and lan? 50MB or 1 GB?(I would compile, configure, etc. on a separate machine

Hi, can anybody comment on the cost of matching with IPP2P vs. Layer7. Also, does a iptables rule with more complicated matching mechanism also slow down processing if all the packets are matched before they reach the rule. I.e. is the mere existence of a potentially costly rule already slowing down processing or only if packets are actually processed by it? Thanks very much in advance.

Hi, I was successfully using VoIP Buster via IAX2 for several weeks now. Yesterday/today it spontaneously stopped working. Using the "real" client the connection works well though. Anybody else experiencing this problem? Or asked differently: Is there anybody for whom it is still working? Can anybody tell me what the problem could be from this: -- Executing

Hello, can anybody interpret what the following means: [root@funke ipp2p-0.8.0]# iptables -t mangle -A MarkList0x666-ipp2p -p tcp -m ipp2p --edk -j MarkSet0x666 iptables: Unknown error 4294967295 ----- I have installed ipp2p-0.8.0 via: make copied ipt_ipp2p.ko to my kernel lib dir copied libipt_ipp2p.so to my iptables lib dir insmod ipt_ipp2p gives the following in dmesg: IPP2P v0.8.0

Hi, it seems that there is a bug in asterisk's dtmf mode autodetection. Assume following sip.conf: [sipprovider] disallow=all allow=g726 dtmfmode=auto DTMF does not work. It seems rfc2833 mode is chosen despite it being obvious that this cannot work! The following configuration is necessary to get DTMF to work: dtmfmode=info In my opinion, this behaviour is counter-intuitive. I am using

Hi, following I would like to implement: 1. I receive a call. 2. I hang up the call. 3. I execute a macro I thought about using call files first... but they don't support macros, or? Then I figured I could use php agi after I receive the call, hang up the call with php agi and execute the macro with "exec ...". Unfortunately, the php agi seems to die with the hangup. Does

Hey, how can I implement a dial plan like the following: incoming call: 1. ring phones 1,2,3 monday to friday between 9:00 and 20:00; if no answer after 15 sec also ring phones 4 and 5 2. ring phone 1 monday to friday between 0:00-9:00 and 20:00-24:00; if no answer after 20 sec also ring phones 2 and 3 3. ring phone 1 saturday and sunday all day I do not need a in detail answer for each of the

Hi, I defined several xen domains with libvirt. Can anybody tell me where libvirt stores these definitions? E.g. what files would one need to back up? Is it correct, that the xen domain definitions in /var/lib/xend/domains are overwritten regularly by libvirt? Many thanks, Arik

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hi, I'm trying to set up an Asterisk pbx based on a Fedora Core 1 Linux box (customized kernel version 2.4.24). I want calls from my SIP soft-phones to simply be dumped onto the PSTN line via a BRI (EuroISDN). I have a cheap HFC-S based PCI ISDN card connected to the NT1+ interface, so I need zaphfc. I've read everything I've found at www.voip-info.org, then I've downloaded the

Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

Hi, I am having problems establishing an adsl connection in dom0 (but ONLY in dom0, without xen everything is ok). Following is my setup/situation: 1. Installed clean Fedora 7 (with virtualization option selected) 2. Booted with the non-xen kernel & setup adsl. Adsl connection works without any problems. 3. Rebooted with xen kernel into dom0. 4. adsl connection can no longer be activated