similar to: Sound warnings bringing asterisk down.

Displaying 20 results from an estimated 2000 matches similar to: "Sound warnings bringing asterisk down."

2004 Apr 21
1
Asterisk from scratch
Hi My motto is to connect two computers on the same network with Voip without using any special hardware,i have downloaded Asterisk, I was suggested to use LinPhone as a soft phone as it is very easy to install I have installed Asterisk on my computer and iam using it as a server. And whe i DAIL 1234 at CLI i get the following errors repeatedly Apr 21 17:29:13 WARNING[1167272128]:
2004 May 26
2
SPAM MESSAGE - [Asterisk-Dev] warning message (sound card) - when I run asterisk!!!
All, After installing asterisk on Linux, I run "asterisk -vvvc". But I got the following warning message: chan_oss.so] => (OSS Console Channel Driver) May 26 00:37:58 WARNING[-1084845952]: chan_oss.c:980 load_module: XXX I don't work right with non-full duplex sound cards XXX == Registered channel type 'Console' (OSS Console Channel Driver) == Parsing
2005 Feb 20
2
Soundcard problems?
Has anybody had any problems with their soundcards like this: Feb 20 01:05:22 WARNING[3420]: chan_oss.c:271 sound_thread: Read error on sound device: Resource temporarily unavailable This shows on the console and I have no clue what it is.. voice prompts sound good.... Any clues? __________________________________________________________________ Anton Krall
2003 Sep 07
1
Sound error during launch
Hello. Although I can hear the demo etc. now, I notice during asterisk launch I get :- [chan_oss.so] => (OSS Console Channel Driver) == Console is full duplex == Registered channel type 'Console' (OSS Console Channel Driver) == Parsing '/etc/asterisk/oss.conf': Found WARNING[98311]: File chan_oss.c, Line 232 (sound_thread): Read error on sound device: Resource
2004 May 28
1
* will not load, after latest CVS install
Greetings I was getting bad static crackle on a phone, so I reload from the latest CVS and did a make clean ; make install on zaptel, libpri and asterisk Now I get this error [chan_skinny.so] => (Skinny Client Control Protocol (Skinny)) May 28 13:59:42 WARNING[16384]: chan_skinny.c:2541 reload_config: Unable to get our IP address, Skinny disabled Urgent handler [chan_oss.so] => (OSS
2003 Aug 18
6
sound problem
hi list, when I run asterisk, appears the following: .... WARNING[1074459808]: File chan_oss.c, Line 346 (setformat): Requested 8000 Hz, got 8178 Hz -- sound may be choppy WARNING[1074459808]: File chan_oss.c, Line 974 (load_module): XXX I don't work right with non-full duplex sound cards XXX WARNING[1133735216]: File chan_oss.c, Line 232 (sound_thread): Read error on sound device: Resource
2003 Sep 13
1
Does * machine need a sound board for MOH?
Does anyone know whether the linux machine running * have to have a sound card on it in order for musiconhold to work for sip phones? I've tried about everything (including tons of google searching) to get it to work, and nothing. When a call is placed on hold between two C7960's, the CLI indicates: -- Executing Dial("SIP/3002-c418", "SIP/3000|20") in new stack
2005 May 16
1
Warning[3817] and REGISTER
Hi, I'm a student working on an implementation of asterisk en linux (red hat 9.0). I'm trying to register a sip softphone (XLite) en asterisk en local. I have 2 problems : - When I execute asterisk there is a warning and a noise in the headphones : May 16 22:12:22 WARNING[3817]: chan_oss.c:269 sound_thread: Read error on sound device: Resource temporarily unavailable Does it come from
2005 Jul 28
2
Asterisk fails to start
Hello, This is debug output I get: Jul 28 15:05:49 WARNING[8249]: chan_oss.c:239 sound_thread: Read error on sound device: Resource temporarily unavailable [chan_zap.so] => (Zapata Telephony w/PRI) Jul 28 15:05:49 WARNING[8249]: chan_zap.c:924 zt_open: Unable to specify channel 1: No such device or address Jul 28 15:05:49 ERROR[8249]: chan_zap.c:6460 mkintf: Unable to open
2003 Jul 20
3
Music on hold & Read error on sound device
I am having a problem getting music on hold working one of my servers. I have had this working on a PII 400 just fine but decided to upgrade my Asterisk server to a PIV 1.5ghz. I have installed mpg123 which seems to be working fine but when I start *, I get the following error message at the CLI prompt when I start *: WARNING[81931]: File chan_oss.c, Line 232 (sound_thread): Read error on
2003 Nov 22
1
g729 codec questions error running asterisk now
Hey all, Does anyone know what this means? I was running asterisk fine. Installed it on a new pc and I am using the g729b. codec that is optional. I ran the install for the codec it went ok but when I run askterisk via asterisk -vvvgc it gives me this error anyone know? I make sure I entered in the correct reg number. I followed the steps correctly. Too Registration error! Please try
2005 Sep 15
5
Asterisk don't start
Asterisk don't running, because show this message WARNING[6949]: chan_sip.c:8865 reload_config: Section 'authentication' lacks type WARNING[6949]: chan_iax2.c:7491 load_module: Unable to open IAX timing interface: No such file or directory WARNING[6949]: chan_skinny.c:2587 reload_config: Unable to get our IP address, Skinny disabled WARNING[6949]: chan_oss.c:239 sound_thread: Read
2003 Nov 19
1
FXO card still won't pick up...
I recently updated (fresh checkout) to the newest zaptel and Asterisk. The one I was using before was a couple of months old. After updating, my zap channels don't work. They won't pick up incoming calls or dial out. When I try to dial out I get: -- Executing Dial("SIP/3064-564c", "Zap/g1/ww954.......") in new stack NOTICE[245776]: File app_dial.c, Line 698
2003 Nov 29
1
asterisk server crashing
I've been running an asterisk server for several months on my RedHat 9 box. Today I decided to update some of the glibc packages on my box and upgrade it to the latest asterisk cvs as well. I can start the asterisk server without incident. I can place a call in from the outside and it takes the call fine; however as soon as I hangup, the server appears to just crash. I have no idea
2005 Jan 11
1
Dial Out Errors
Hey, I'm having some errors whenever I dial out and I can't dial in at all. I'm using NuFone as my provider just so you know. Jan 11 17:39:46 WARNING[1771]: chan_oss.c:413 soundcard_setinput: Unable to re-open DSP device: No such device Jan 11 17:39:46 WARNING[1771]: chan_oss.c:572 oss_write: Unable to set device to input mode Jan 11 17:39:46 WARNING[1771]: app_dial.c:359
2004 Aug 26
1
Newbie needs help - Dev_Kit_Lite installation problem
Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here
2003 Nov 25
1
About sound modules in Asterisk. And call gnophone-asterisk-h323
Hi, First at alll, I beg your pardon because maybe I explained bad my questions (because my low level english) I have asterisk 0.5.0, asterisk-oh323-0.5.6, openh323-1.12.2 and pwlib 1.5.2 compiled and installed. I have modules alsa 0.9.8 compiled and installed My PC has an audio card ac97 chipset intel i810 in its motherboard. I want to use asterisk in this way: |PC linux | --ethernet--
2003 Jun 13
5
Applications, dialplan not loading
I've built the latest CVS of asterisk -- not the zaptel or libpri directories, just the asterisk directory. asterisk installs successfully, but there are severe problems. I built this system in the past and ran it, but now building it again fails. This is the CVS as of this morning, 2003-06-13, but I had problems on 06-11/12 as well. After make; make install; make samples; make config, I
2005 Aug 08
0
Configuring TDM40B and X100P
Hi, I get the following message when I try to run Asterisk. This happened after I changed some of the configuration files: extensions.conf, zaptel.conf and zapata.conf. I have both TDM40B and X100P cards and am trying to use them together. Please let me know if there is something else I should do. Thnx, Gladys [chan_local.so] => (Local Proxy Channel) == Registered channel type
2003 May 22
0
Some warnings when starting Asterisk
Hi, When I start asterisk with asterisk -vvvvc it works preaty well, but I get the following warnings: Warning, flexibel rate not heavily tested! WARNING[1074494176]: File res_musiconhold.c, Line 462 (moh_register ): Unable to open pseudo channel for timing... Sound may be choppy. WARNING[1074494176]: File res_musiconhold.c, Line 462 (moh_register ): Unable to open pseudo channel for timing...