similar to: [Asterisk-Dev] SIP channels not cleared

Hello all I've discovered that SIP channels sometimes get stuck in *. I've read some posts from Fri 29 Aug 2003 which mentions this issue, but there doesn't seem to be any final answers I don't know if this is related to the 0001604 bug? Below is a list from one of the incidents: I know the (d) means that it is scheduled for destruction but the 10.1.1.45 channel hasn't

I am using Asterisk 1.4.18 with 70 various Polycoms, 12 analog, and 18 Spectralink wireless IP phones. Most of the Spectralink phones have entries in 'sip show channels' that do not go away. None of the other phones do this. Is there anyway to remove these entries without restarting Asterisk? Any ideas on what could be done to prevent this? Example output: xxx.xxx.xxx.xxx 541

'morning everybody, Here is the setup: 5126800422 called 3035 (3035 is a Cisco 7960). The call is g729. 3035 presses 'Conference' on her phone and calls 8327549222. This call is ulaw. (65.72.107.2 is our Cisco 7206 SIP->PRI gateway.) asterisk*CLI> sip show channels Peer User/ANR Call ID Seq (Tx/Rx) Format 65.72.107.2 8327549222 1758081f67e

Hello, In a couple of Asterisks, after type "sip show channels" we have a lot of these: IP_PEER dst_number something 00102/00103 unkn No (d) Rx: BYE IP_PEER dst_number2 something2 00102/00103 unkn No (d) Rx: BYE We are using ASterisk 1.2.x When I say "a lot" I mean more than 180, more than 230, etc. Is it normal? How we can remove it? Thank you very much, --

Hi all! Quite a mystery. The following happened when I was on holiday, and no one else has changed any configs of either Asterisk or the Cisco's in the building... The situation: Incoming works fine on all phones. Outgoing only works from non-Cisco phones. When calling from a Cisco phone to an external phone, all the Cisco-user hears is a ticking crackle and after about a minute the phone

Through my Asterisk server, I am trying to use IAXTel to dial 800-type numbers (yes, I know I can do the same thing with FWD and others via SIP, but I wanted to play with IAX a little). It appears I'm running into some sort of a codec mismatch or something because it's not working right. The SIP client is a SPA-3000. In iax.conf, I have something like the following: [General]

I've the following situation: Phone A: Codec GSM supported Phone B: Codec iLBC supported in sip.conf: [general] ... disallow=all allow=gsm allow=ilbc allow=alaw allow=ulaw canreinvite=yes ... (There's a lot of other SIP users, that's why I made the default codec list bigger than just GSM and/or ALAW) If phone A calls to phone B the conversation is established at SIP level, but

Hi All. This is on Asterisk 1.2.13 I place a call between 2 SIP phones (with canreinvite=yes, qualify=yes). I reset the phones (so they don't have time to say BYE). Asterisk seems to think that the call is still ongoing. This persists until I do a 'restart now'. asterisk1*CLI> show channels Channel Location State Application(Data) SIP/5301-089fc890

I am having a problem when a SIP registration fails. I get the following messages in the log: Sep 25 18:51:02 NOTICE[1125329600]: File chan_sip.c, Line 2874 (sip_reg_timeout): Registration for '<user>@fwd.pulver.com@65.39.205.114' timed out, trying again Sep 25 18:51:02 NOTICE[1125329600]: File chan_sip.c, Line 5119 (handle_request): Registration from

Hi Jerry et al, I recently installed the 3.0.1 release, since then I can not install any drivers as admin user :-( I'm running on Solaris 9 with ads (mybe I missed anything): [2003/12/18 13:56:58, 0] smbd/service.c:set_admin_user(321) lp logged in as admin user (root privileges) [2003/12/18 13:57:27, 0] smbd/connection.c:register_message_flags(220) register_message_flags: tdb_fetch

I have a high volume asterisk 1.40 installation and I ran a SIP SHOW CHANNELS. (see partial output below). My questions are: 1. "wc-l" of the output shows 4000 lines. Does this mean 2000 active calls? (2 channels per call) 2. The latter part of the output shows "unkn" for Form column. Why does it not know the codec? Could it be UDPTL? Or are these calls messed up? 3.

I am using a2billing as calling card platform with asterisk 1.2.17. After running for several days, if I issue 'sip show channels' command, I got a lot of dead sip channels although 'show channels' command only show 5 channels. What cause these dead channels? How can I clean out these dead channels? Will they pose any problem to my * server if left alone? What does this (d) mean?

Hi, I am using Trxibox 2.6 latest ISO install. Following is the output of : "sip show channels" [trixbox ~]# /usr/sbin/asterisk -rx "sip show channels" Peer User/ANR Call ID Seq (Tx/Rx) Format Hold Last Message 212.53.40.40 0218245 6cfb845d050 09011/00000 0x0 (nothing) No 192.168.1.116 (None) YTc4ZmM3NjV 00101/00006 0x0

Hi, I'm trying to view a list of the active calls to see if I can restart Asterisk. When I do 'sip show channels', I get a huge list like this (just a sample pasted):- 92.110.7.210 (None) 198827f2469 00102/00000 0x0 (nothing) No Init: OPTIONS 92.110.7.210 (None) 6b211bb04ac 00102/00000 0x0 (nothing) No Init: OPTIONS 92.108.34.153

Hello everyone, I'm getting DIALSTATUS=CHANUNAVAIL when a call is trying to get one of my queue interfaces, despite the fact it is free at that time, can you give help? 1. I see many sip channels from that extension: [root at mysweetpbx]# asterisk -rx "*sip show channels*" |grep 648 Peer User/ANR Call ID Seq (Tx/Rx) Format Hold

Hi all, I have been asked to look into using asterisk as part of our setup. The eventual goal is to replace as many parts of the existing setup as possible, but in the interim, I just have to make it bolt on and work with all existing parts. My current setup is as follows: Cisco 7940 (ext 2000) | v Asterisk -> Snom SIP proxy(v2.22) -> Vega100 PSTN gw -> Index PBX |

My sip show channels shows some channels active that I can not make sense out of, and they have been that way for days, so I am pretty sure they are orphans. Is there a way to show active CALLS (instead of channels) to try and determine the source? Does the output below provide any clues as to why these channels might show active? Anyone aware of related bugs? The #'s indicate original

We are using G711 for phones to talk to Asterisk and G729 licenses at asterisk to talk to ITSP Could you please suggest transcoder to use from G711 and G729 and which is comptible with Asterisk. We will like to avoid using TDM if possible Also i remember that initially we didn't have G729 and were using only 711 for with vicidial but then also we had same problems. at that time it was only 2

Hello my friends... Currently we are using the following firmware versions on ours aastra 55i: Firmware Information Attribute Value Firmware Version 2.1.0.2145 Firmware Release Code SIP Boot Version 2.0.1.1055 Date/Time Jun 20 2007 06:20:29 Can we make a firmware upgrade to the latest one: 6755i (55i) SIP, V2.5.3.18, January 2010 , English , ZIP , 2,849 KB on the site:

on sip show channels I do get a lot of entrys like 192.168.1.47 11 07ba5a490b3 00102/00000 unkn No Init: INVITE 192.168.1.47 11 19090f115b8 00102/00000 unkn No Init: INVITE 192.168.1.47 11 7d8b8fde46f 00102/00000 unkn No Init: INVITE How do they appear? How can they be removed? "core show channels" does not list them. Elmar