similar to: OT: Anyone having issues with sipphone?

Does anyone else have DTMF issues with SIPPhone? When calling into my DID, and entering, say, 1002. Sometimes it will recognize it properly (rarely), other times it will receive something different. Such as, 1102 or 1000, etc. Has anyone else been having these issues? I'm only accepting ulaw and alaw, and my relevant sip.conf information follows: [sipphone] type=peer

Hello, can anyone comment on how one could use SIPphone's $89 All-in-One adapter with Asterisk? Sounds to me like it should work as both a FXO and FXS. It would be a cheap way of getting started with Asterisk and PSTN. Any comments on the SIPphone FX200? Any comments on SIPphone in general? Thank you for your help

When attempting to call one of the example numbers, like 17474745000, I only get "488 Not Acceptable Here". It works fine when I configure the softphone (Xten X-Lite) to use sipphone's server directly. Am I missing something? Here's my relevant config sections: sip.conf: in [general]: register => 17472442457:mypassword@proxy01.sipphone.com [sipphone] type=friend

Hi, Does anyone know how to dial toll-free (800) numbers through FWD or Siphone? Using the configuration below, I can dial out to SIPphone.com users by simply dialing their number (1747XXXXXXX) and can dial out to FWD users by dialing 1383<FWD#> However, when I dial 18005551212 through SIPphone, or through FWD (depending upon which line is selected in "; 800 Toll Free Numbers"

Hello All. I started setting up my Asterisk system yesterday and everything was going well, i have registered with sipphone.com and set-up my Asterisk system to register with sipphone per the sip.conf file below. It was registered perfectly but I could not receive calls so I added in the line "insecure-very" and I then used the Washington DC access number to test and the phone

Hello when i dial a toll free no using sipphone i get this error message. How do i solve this? Any help will be appreciated. console message: Starting simple switch on 'Zap/2-1' -- Executing SetCallerID("Zap/2-1", "17473863282") in new stack -- Executing SetCIDName("Zap/2-1", "Deepak JV") in new stack -- Executing

for inbound calls, i can register context = from-sipphone register => 1747xxxxxxx:passwd@proxy01.sipphone.com but how do i configure to make outbound calls to them? exten => _1747XXXXXXX,1,GoTo(dial-sipphone,${EXTEN},1) .... [dial-sipphone] ; ; SIP to sipphone.com ; exten => _X.,1,Dial(SIP/${EXTEN}@??????) ^^^^^^

I have been successfully connected (incoming and outgoing) to FWD for a very long time. A few months ago, I changed from SIP-based FWD service to IAX2-based, and that went fine as well, both incoming and outgoing. At the time, I was running Asterisk 1.0.3 Stable. I rarely use the service, so other than noticing that I was always successfully registered to FWD, I didn't make or receive calls

I'll admit it. I'm a asterisk newbie (but no stranger to telephony). The setup is simple: two Grandstream BudgeTel 100 phones (SIPPhone specials) on a private segment calling to a Linux box acting as the segment's firewall with a leg on our public network. The phones are setup as SIP/phone1 (x1000) and SIP/phone2 (x1001), respectively (thanks to the Asterisk HOWTO). Getting IAX

I seem to be having a problem with transcoding and/or agreeing on a valid codec. I am running a new image pulled from CVS at 1:30 PM CST. The issue occurs when I try to make a call to a toll-free number over sipphone.com. Here's what I see in the console: NOTICE[1259545280]: File channel.c, Line 1478 (ast_set_read_format): Unable to find a path from G729A to ULAW NOTICE[1259545280]: File

Has anyone else had problems registering with Sipphone over the last few weeks? Previously, this had worked fine. I contacted Sipphone technical support, but they're not much help. register => 17471234567:password@northamerica.sipphone.com/123

Hi all. I found a connection error from sipphone.com. It seems 'realm based authentication' by sipphone.com. any ideas? Regards. mack

Should SipPhone support ISN routing for their 747 ITAD? Cast a vote: http://forums.gizmo5.com/viewtopic.php?t=10197 Meanwhile if you're interested, you can use the Nerd Vittles 'bandit' ITAD #1089 to call a SipPhone/Gizmo5 subscriber via ISN, which I think is clever (Karl tips his hat to Ward Mundy) and it's also really, really funny.

Hello all, I''m having a bit of an internal conflict here. I have a web application that I need to write (for myself). Fine, right? Well, this site is for a DNS service that has a client interface for client APIs to access. I''d like to have all application requests and data updates/retrieval to go through this interface instead of a database. Should I even use Rails for

Hi All, I know off topic, but I just cant get solutions and you all are always so helpful. I have a blackberry curve 8310 and I really need to keep track of clients, their e-mails, notes, pdfs, etc. basically everything about a customer. I want to deploy it here in my apartment (I have a static IP) and either have my BB connect or sync at the end of the day or something. I just cannot

Looking for a quality alternative... if there is one :-). John Kopanas http://www.kopanas.com ===================================================================== http://www.soen.info - source of the freshest software engineering information on the net http://cusec.soen.info - software engineering conference

Ok just curious how many hits the http://isoredirect.centos.org/centos/5/isos/ URL was getting? lol I think I check at least 4-5 times a day and all of a sudden instead of forbidden error I got in!!! ... only to find the tail end of some of the powers' humor: "5 hasnt been released" LOL I just about fell over -- L -- "To mess up a Linux box, you need to work at it; to mess

I'll ask more specific questions if so :-) Need to pull some usage data via a script and Oracle suppport says it can't be done. I have trouble believing that. -- ?Don't eat anything you've ever seen advertised on TV? ? ? ? ?? - Michael Pollan, author of "In Defense of Food"

Any sip softphone will work.? Linphone is free. I have tested many . All works well with audio.? -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20131102/21e533b0/attachment.html>

[Dec 31 10:39:45] WARNING[17884]: pbx.c:2518 __ast_pbx_run: Invalid extension '11', but no rule 'i' in context ...[snip]... When testing IVR and pressing "1" from my Grandstream SIP-phone, the above message is printed on the Asterisk CLI. How come Asterisk receives my "1" as "11" ?? Settings in my SIP-phone are : Send DTFM : via RTP(rfc2833) &